• Journal of Advanced Marine Engineering and Technology
• /
• 제41권2호
• /
• pp.140-145
• /
• 2017

Newly designed vapor-injection heat pumps have been proposed and analyzed in the present study. An economizer-type vapor-injection (V-I) system has been employed as the standard system because of its reliability and simple control method. The V-I system has a re-cooler and re-heater for cooling and heating, respectively. Solar panels have been installed in the V-I heat pump as well as in the re-heater in order to enhance heating capacity and performance. R410A has been employed as a working fluid and performance analysis has been conducted under various conditions. Results are summarized as follows: (1) The V-I system with the re-cooler yielded a marginally higher coefficient of performance (COP) than the conventional V-I refrigeration system. (2) By increasing the re-cooler cooling capacity, enhanced system performance as compared to the conventional V-I system was observed. (3) The re-heater negatively affected the system performance; hence, the V-I heat pump with the re-heater yielded a lower COP than that of the conventional V-I heat pump used for heating. (4) Although the solar panels increased the system performance, this increase could not offset performance degradation by the re-heater.

• 한국해양공학회지
• /
• 제32권5호
• /
• pp.372-379
• /
• 2018

High-pressure gas injection engines (HPGI) took center stage in LNG carrier propulsion systems after their advent. The HPGI engine system can be easily modified to include a re-liquefaction system by adding several devices, which can significantly increase the economic feasibility of the total system. This paper suggests the optimal operating conditions and capacity for a re-liquefaction system for an LNG carrier, which can minimize increases in the total annualized cost. The installation of a re-liquefaction system can save 0.23 million USD per year when the cost of LNG is 5 USD/Mscf. A sensitivity analysis with different LNG costs showed that the re-liquefaction system is profitable when the LNG cost is higher than 3.5 USD/Mscf.

• 시스템엔지니어링학술지
• /
• 제14권2호
• /
• pp.49-57
• /
• 2018

The main objective of this paper is come up with methodology approach for FPGA-based system in verification and validation lifecycle regarding software reliability using system engineering approach. The steps of both reverse engineering and re-engineering are carried out to implement an FPGA-based of safety critical system in Nuclear Power Plant. The reverse engineering methodology is applied to elicit the requirements of the system as well as gain understanding of the current life cycle and V&V activities of FPGA based-system. The re-engineering method is carried out to get a new methodology approach of software reliability, particularly Software Reliability Growth Model. For measure the software reliability of a given FPGA-based system, the following steps are executed as; requirements definition and measurement, evaluation of candidate reliability model, and the validation of the selected system. As conclusion, a new methodology approach for software reliability measurement using software reliability growth model is developed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.361-364
• /
• 1997

The re-enty guidance design involves trajectory optimization, generation of a reference drag acceleration profile with the satisfaction of trajectory constraints. This reference drag acceleration profile can be considered as the reference trajectory. This paper proposes the atmospheric re-entry system which is composed of longitudinal, later and range control. This paper shows the a performance of a re-entry guidance and control system using feedback linearization control and predictive control.

• 한국정보과학회논문지:소프트웨어및응용
• /
• 제29권9호
• /
• pp.619-630
• /
• 2002

1980년대 이후, 소프트웨어 위기에 대응하기 위한 다양한 소프트웨어 공학적 기법들이 출현하기 시작 하였고, 현재 소프트웨어의 질적 향상 및 생산성 향상을 꾀하기 위한 개발 지침으로 소프트웨어 컴포넌트 개발 프로세스를 구축하는데 관심이 집중되어지고 있다. 그러나 대부분의 방법론들이 앞으로 구축할 새로운 시스템의 재사용성 확보에 치중할 뿐, 실질적으로 기존 레거시 시스템의 자원을 재사용하여 새로운 시스템을 구축하는 방법은 효율적으로 지원하지 못하고 있는 실정이다. 본 논문에서는 레거시 시스템의 효율적 재사용을 위한 재공학 프로세스(Reengineering Process)로 RUP를 확장, 커스터마이징하여 구성한 RUP+re을 제시한다. RUP+re은 크게 역공학 워크플로우(Reverse Engineering Workflow), 재공학 워크플로우(Re-Engineering Workflow), 순공학 프로세스(Forward Engineering Process)로 구성되어진다. RUP+re의 각 워크플로우와 세부스텝을 제공하고 실사례 연구를 통하여 실질적으로 프로세스를 검증함으로서 레거시 시스템 자원의 재사용을 위한 소프트웨어 재공학 프로세스 구축에 효율적인 지침을 제공한다.

• 산업경영시스템학회지
• /
• 제21권47호
• /
• pp.125-138
• /
• 1998

In this paper, we investigate the effect of re-entrance to the same work station in a job shop with multiple identical machines. System A is defined as the system in which re-entrance is not permitted, and system B is defined as the system in which re-entrance is permitted. By the analytical result of the queueing network, we find that the two systems have the same queue length distributions and utilizations under FIFO dispatching rule when all parameters are same. Simulation models are developed for various comparisons between the two systems, and simulation experiments are conducted for the combinations of five dispatching rules, two average workloads and two due date allowances. Five performance measures are selected for the comparison. The simulation results show that permitting re-entrance affects for some combinations of system environments.

• 동력기계공학회지
• /
• 제19권4호
• /
• pp.69-75
• /
• 2015

In this study, the characteristics of heating performance of a high-performance air-cooled heat pump with vapor-injection(VI) cycle using re-heater was investigated experimentally. Devices used in the experiment is consist of a VI compressor, condenser, oil separator, refrigerant (economizer outlet refrigerant) re-heater, economizer, evaporator. And R410A was used as a working fluid. The experiment was conducted with two cycles(cycles A and B) for investigating heating performance. In case of cycle B, heat exchange was conducted by re-heater between outlet refrigerant of compressor and suction refrigerant of the VI system(Fig.1, re-heater). But the re-heater was not used in case of cycle A. As a result of this experiment, discharge temperature of refrigerator in compressor was shown higher value, when the cycle B was conducted, because of the heat exchange between suction refrigerant of VI cycle and outlet refrigerant of compressor in the re-heater than cycle A that was not use re-heater. it means that liquid hammer and the decrement of heating performance can be decreased by using re-heater. Also, Heating coefficient of performance(COPh) was shown about 2.98 in Cycle B which was 4% higher than Cycle A and from these results, It was confirmed that the improvement of the heating performance of heat pump with VI cycle can be achieved by applying re-heater.

• Nuclear Engineering and Technology
• /
• 제55권9호
• /
• pp.3320-3325
• /
• 2023

The scaled water-cooled Reactor Cavity Cooling System (RCCS) experimental facility reproduces a passive safety feature to be implemented in Generation IV nuclear reactors. It keeps the reactor cavity and other internal structures in operational conditions by removing heat leakage from the reactor pressure vessel. The present work uses Flownex one-dimensional thermal-fluid code to model the facility and predict the experimental thermal-hydraulic behavior. Two representative steady-state cases defined by the bulk volumetric flow rate are simulated (Re = 2,409 and Re = 11,524). Results of the cavity outlet temperature, risers' temperature profile, and volumetric flow split in the cooling panel are also compared with the experimental data and RELAP system code simulations. The comparisons are in reasonable agreement with the previous studies, demonstrating the ability of Flownex to simulate the RCCS behavior. It is found that the low Re case of 2,409, temperature and flow split are evenly distributed across the risers. On the contrary, there's an asymmetry trend in both temperature and flow split distributions for the high Re case of 11,524.

• 한국IT서비스학회지
• /
• 제2권1호
• /
• pp.111-121
• /
• 2003

This paper intents to suggest the re-engineering methodology to transform and integrate the legacy systems to new system in modern environment. While existing reverse engineering and re-engineering approaches have focused on analyzing and maintaining the source code of program. our methodology can provide the procedures and techniques for evolving into new system by recovering the reverse engineering informations and transforming them into component informations. Our methodology for componentization of legacy system is consisted of plan step, reverse engineering step, componentization step, and delivery step, and we describes activities and detail procedures about each step.

• 정보처리학회논문지D
• /
• 제10D권5호
• /
• pp.845-858
• /
• 2003

1980년대 이후, 소프트웨어 위기에 대응하기 위한 다양한 소프트웨어 공학적 기법들이 출현하기 시작 하였고, 현재 소프트웨어의 질적 항상 및 생산성 향상을 꾀하기 위한 개발 지침으로 소프트웨어 개발 프로세스를 적용하는데 관심이 집중되어지고 있다. 그러나 대부분의 방법론들이 앞으로 구축한 새로운 시스템의 재사용성 확보에 치중할 뿐, 기존의 레거시 시스템 자원을 재사용하여 새로운 시스템을 구축하는 재공학 방법은 지원하지 못하고 있는 실정이다. 본 논문에서는 레거시 시스템의 효율적 진화를 위한 재공학 프로세스(Reengineering Process)로 RUP를 확장, 커스터마이징하여 구성한 RUP+re을 제시한다. RUP+re는 Small-h 모델을 바탕으로 크게 역공학 워크플로우(Reverse Engineering Workflow), 변환 워크플로우(Transformation Workflow), 진화 워크플로우(Evolution Workflow)로 구성되어진다. RUP+re의 각 워크플로우와 세부스텝을 제공하고 재공학 사례 연구론 통하여 실질적으로 프로세스를 검증함으로서 레거시 시스템 자원의 진화론 위한 소프트웨어 재공학 프로세스 구축에 효율적인 지침을 제공한다.