• Journal of the Korean Chemical Society
• /
• v.56 no.5
• /
• pp.609-616
• /
• 2012

Ba-ferrite ($BaFe_{12}O_{19}$) nanoparticles were synthesized by chemical coprecipitation method in an aqueous solution. The particle size and the crystallization temperature of the Ba-ferrite nanoparticles were controlled varying the precipitation temperature. The precipitate that was prepared at $0^{\circ}C$ showed the crystal structure of Ba-ferrite in X-ray diffraction when it was calcined at the temperature above $580^{\circ}C$, whereas what was prepared at $50^{\circ}C$ showed the crystallinity when it was calcined at the temperature higher than about $700^{\circ}C$. The particle sizes of the synthesized Ba-ferrite were in a range of about 20-30 nm when it was prepared by being precipitated at $0^{\circ}C$ and calcined at $650^{\circ}C$. When the precipitation temperature increased, the particle size also increased even at the same calcination temperature. The magnetic properties of the Ba-ferrite nanoparticles were also controlled by the synthetic condition of precipitation and calcination temperature. The coercive force could be appreciably lowered without a loss of saturation magnetization when the Ba-ferrite nanoparticles were prepared by precipitation and calcination both at low temperatures.

• Journal of Advanced Marine Engineering and Technology
• /
• v.6 no.2
• /
• pp.21-41
• /
• 1982

Viscosity, especially characteristic among various properties of visco-elastic fluids such as high polymer solutions, is affected mainly by temperature and concentration. Hence, it is important for fluid engineering to express, by some equations, how the fluid characteristics vary with the change of temperature and concentration and to analyze them to obtain consistent viscous characteristics. High polymer solutions, synthetic products of modern chemical industry, suggest many interesting investigations because they are typical visco-elastic materials. Experimentation was made to derive some useful fluid characteristic equations of SEPARAN-NP10 (polyacylamide) expressed by n (flow behavior index) and K' (consistency index) when it is given temperature and concentration variation. To measure viscosity, capillary viscometer was adopted and the range of experimentation is 0-2,000 P.P.M. in concentration and 15-55 .deg.C in temperature. The experimental results are summarized as follows: The flow behavior index n 1) has nearly constant results irrespective of temperature variation at same conentration and the results are shown in (Table. 4-4-3) 2) has following equation, regardless of temperature, for the variation of concentration. n=-1.0765*10$^{-4}$ P+0.9915 (P:P.P.M.) The consistency index K' 1) has different results for the variation of temperature at same concentration and the results are given in (Table.4-7-2) 2) has following equation for the variation of concentration at same temperature. log 10$^{4}$K' =6.4785*10$^{-4}$ P-1.0529 (P:P.P.M)

• Journal of Korean Society on Water Environment
• /
• v.27 no.6
• /
• pp.769-775
• /
• 2011

An experimental study of biofilm nitritation system for high-strength ammonium wastewater has been carried out to examine the temperature effect on different organic and solid concentration. Operating temperature varied from $35^{\circ}C$ to $15^{\circ}C$. The influent N concentration of identical three reactors was adjusted to about $300mg\;NH_4-N/L$. A control unit fed with a synthetic wastewater, while the others were fed with reject water which is consisted of the supernatant of both digester and thickener. The results indicated that nitrite accumulation was stable in temperature range of $35^{\circ}C$ to $25^{\circ}C$. However, nitritation was significantly reduced at below $20^{\circ}C$. Free ammonia (FA) and free nitrous acid (FNA) were major inhibitors to the nitrite oxidizer for nitrite accumulation in lower temperature. From the estimation of temperature coefficient (${\Theta}$) of biofilm and suspended nitritation system, biofilm nitritation system could absorb the negative temperature effect compared with suspended nitritation system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3761-3767
• /
• 2009

This study was investigated to determine the combustion characteristics, decomposition efficiency, and the flue gas concentrations after combustion in the high temperature reactor($1,250{\sim}1,400^{\circ}C$, 1 atm) for the liquid wastes(waste oil and waste solvent) generated from the industrial complex. The concentration of nitrogen oxide(NOx) is decreased and the synthetic gas is increased when the mass ratio of $O_2$/waste is about 1.53 because the reaction condition was changed to reduction state. And BTEXs(benzene, toluene, ethylbenzene, xylene) are decomposed more than 99.99%. If the highly concentrated liquid waste (waste oil and waste solvent) is treated under the operating conditions suggested by this study, our treatment method for the liquid waste was found to be proper because of the contaminants emission concentration is very low. In addition, the synthetic gas after combustion can be used as an alternative fuel.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1076-1086
• /
• 1994

This study covers synthetic effect of the various hydrothermal treatments on formation of artificially made kaolinite mineral. The hydrothermal treatment includes the temperature treatment with time duration, addition of seeds, particle size of the starting material used, pH variation and the different types of organic acids. A colloidal silica and alumina sol which are commercially available are used for this study. A colloidal silica and alumina sol are mixed by the atomic ratio of Al/Si = 1, based on the theoretical kaolinite composition and calcined at $600^{\circ}C$ for 8 hours duration. It was found that the kaolinitic clay mineral was well developed; thereby, the different patterns of crystalline mineral are appeared. Spherical type as a crystal form was distinctively formed at the temperature of 20$0^{\circ}C$ to 25$0^{\circ}C$ with short duration time, while platy type as a crystal was highly yielded at 300~35$0^{\circ}C$. Moreover, by adding more than 20 wt% of seed as the natural kaolinitic clay to the starting material is widely distributed and developed when 2 ${\mu}{\textrm}{m}$ or less particle size of the starting material is used; also, when they are heat-treated at the temperature of 25$0^{\circ}C$ with 5 hours duration. With respect of the effect of pH variation on formation of the synthetic kaolinite minerals, the crystalline minerals are highly yielded at less than pH 2 and gradually diminished at more than pH9. Regarding to the effect of different acids on development of the kaolinite mineral, the organic acids with high chelating capacity produces good formation of crystalline minerals; whereas, amine radical-(NH2) is not an effective agent to generate the crystalline minerals.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.18 no.5
• /
• pp.661-673
• /
• 1994

We have gathered a fatty acid to recycle the waste oil of food manufacturing process, and then made a soap from the waste oil by alkali saponification. Effects of the washing elements such as the concentration of the soap, temperature and time were evaluated to find out the optimum washing conditions, and results are as follows. 1. We could find soaps made from the soybean oil (A), corn oil (B), rape seed salad oil (C), cotton seed oil (D) and a soap consisting of the each oil 25% respectively (I) had the lowest surface tension at the concentration of 0.225% -0.25%. Compared with the single fatty-acid soap, the multi-component soap I showed the lower surface tension at the cmc. 2. All the samples of A-I showed the lowest contact angle for the solid material at the concentration of 0.25%. The multi-component soap of I showed higher contact angle than the single.component soaps of A, B, C and D. 3. The soap G, made from the waste oil, show lower surface tension than 5, made from the complex raw fats of the eatable fatty oil acid and H, commercial soap. 4. The washing efficiency depends on the washing time. Especially the 25-minute was found to be the optimum washing time. 5. The highest washing efficiency was found at the 0.25% cont. reagardless of the washing temperature. At 0.15% concentration level the washing efficiency reduces as washing tem- perature increases. At 0.3% concentration level the highest washing efficiency was found between $50^{\circ}$-$60^{\circ}$. 6. The soap made from the waste oil showed the highest washing efficiency in terms of concentration, temperature, and time. 7. The soap made from the waste oil showed the similiar concentration of hydrogen ion to the synthetic detergent. 8. The hand value of the fabric washed by the soap made from the waste oil was a little lower value than those washed by the synthetic detergent.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.2
• /
• pp.264-271
• /
• 2006

Two fibrinolytic enzymes were purified from the culture supernatant of Fomitella fraxinea mycelia by ion-exchange and gel filtration chromatographies, and were designated as F. fraxenia proteases 1 and 2 (FFP1 and FFP2). The apparent molecular masses of the enzymes were estimated to be 32 kDa and 42 kDa, respectively, by SDS-PAGE and gel filtration chromatography. Both enzymes had the same optimal temperature ($40^{\circ}C$), but different pH optima (10.0 and 5.0 for FFP1 and FFP2, respectively). FFP1 was relatively stable at pH 7.0-9.0 and temperature below $30^{\circ}C$, whereas FFP2 was very stable in the pH range of 4-11 and temperature below $40^{\circ}C$. FFPI activity was completely inhibited by phenylmethylsulfonyl fluoride (PMSF) and aprotinin, indicating that this enzyme is a serine protease. The activity of FFP2 was enhanced by the addition of $CO^{2+}$ and $Zn^{2+}$ and inhibited by $Cu^{2+},\;Ni^{2+}$, and $Hg^{2+}$. Furthermore, FFP2 activity was strongly inhibited by EDTA and 1,10-phenanthroline, implying that the enzyme is a metalloprotease. Both enzymes readily hydrolyzed fibrinogen, preferentially digesting the $A{\alpha}$- and $B{\beta}$-chains of fibrinogen over ${\gamma}$-chain. FFP1 showed broad substrate specificity for synthetic substrates, but FFP2 did not. $K_{m}$ and $V_{max}$ values of FFP1 for a synthetic substrate, N-succinyl-Ala-Ala-Pro-Phe-pNA, were 0.213 mM and 39.68 units/ml, respectively. The first 15 amino acids of the N-terminal sequences of both enzymes were APXXPXGPWGPQRIS and ARPP(G)VDGQ(R,I)SK(L)ETLPE, respectively.

• Fashion & Textile Research Journal
• /
• v.15 no.3
• /
• pp.461-466
• /
• 2013

Synthetic fiber materials were developed due the desire of consumers for high-quality, high-performance and comfort. A high functionality of synthetic fiber can be obtained through surface treatment that can improve hydrophilic properties, color depth after dyeing and adhesion properties. These advantages create added-value. Hydrophobic properties are an important feature to create added-value (such as hydrophilic properties). One side processing is a method of imparting to contrary function on the front and rear side. In this study, fluorine-coated Nylon/PU blended fabric was treated on only one side with a low-temperature plasma treatment; subsequently, the contact angles decreased by increasing the time and intensity of the plasma treatment. The contact angle of the untreated surface and the treated surface was different. It a showed a difference in the properties of both surfaces. Tensile strength and stiffness decreased by increasing the time and intensity of the plasma treatment. However, plasma treatment did not significantly change the tensile strength and stiffness on both surfaces of the fabric. SEM photographs showed the surface of fluorine-coated fabric and the etching surface by using plasma treatment on the fabric. Plasma treatment was confirmed not to affect the physical properties of the fabric.

• Journal of Magnetics
• /
• v.7 no.2
• /
• pp.29-39
• /
• 2002

The initial NiCuZn synthetic ferrite were acquired from thermally decomposing the metal nitrates $Fe(NO_3)_39H_2O, Zn(NO_3)_26H_2O, Ni(NO_3)_26H_2O, and Cu(NO_3)_23H_2O$ at $150^circ{C}$ for 24 hours, and then we calcined the synthetic powder at $500^circ{C}$, pulverized each of those for 3, 6, 9, 12, and 15 hours in a steel ball mill, sintered each at $700^circ{C}$ to $1,000^circ{C}$ for 1 hour, and thus studied their microstructures and electromagnetic properties. We could make the initial specimens chemically bonded in liquidity at a low-temperature $150^circ{C}$, by using the low melting points less than $200^circ{C}$ of the metal nitrates instead of the mechanical ball-mill pulverization, then narrow a distance between the particles into a molecular one, and thus lower the reaction point of sintering by at least $200^circ{C}$ to $300^circ{C}$. Their initial permeability was 50 to 400 and their maximum magnetic induction density and coercive force, 2,400 G and 0.3 Oe to 0.5 Oe respectively, which was similar to those of NiZnCu ferrite synthesized in the conventional process. In the graph of initial permeability by frequencies, a $180^circ{C}$ rotation of the magnetic domains which appears in a broad band of micro-wave before and after the resonance frequency, could be perceived.

• Tribology and Lubricants
• /
• v.34 no.5
• /
• pp.197-207
• /
• 2018

Thermal deterioration of fuel due to long-term storage influences engine performance and causes malfunctions. Fuel stability is usually evaluated via heat resistance and thermal stability during a brief heat shock at high temperature; storage stability in this scenario means that there is very little change in the quality of the fuel during long-term storage. In addition, rubber-based products such as oil seals, O-rings, and rubber hoses can influence the quality of the fuel. When these rubber products are in contact with fuel, they can swell, mechanically weaken, and occasionally crack, thus leaking low molar weight rubber and additives including plasticizer and antioxidant into the fuel to degrade its properties and shorten its useful lifetime. This study determines the thermal stabilities of three kinds of synthetic fuels by evaluating their low temperature kinematic viscosities, chemical composition changes via GC analyses, gross heat of combustion, and color changes. We evaluate the compression set of O-rings by immersing one NBR and two FKM rubber O-rings in the three synthetic fuel samples in airtight containers at variable storage temperatures for six months; from this, we estimate the lifetimes of the O-rings using the Power law model. There were very little changes in the chemical compositions and gross heat of combustion after six months of the experiment. The lifetimes are thus dependent on the materials of the rubber products, and in particular, the FKM O-ring was calculated to have a theoretical lifetime of 200 to 5,700 years. These results indicate that the synthetic fuels maintain their physical properties even after long-term storage at high temperatures, and the FKM O-ring is suitable for long-term sealing of these fuels.