• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.991-997
• /
• 2004

In this paper, we propose the architecture of modem receiver to fabricate HomePNA 2.0 chip. HomePNA suffers from inferior channel because of bridge tap, the effect of amateur HAM band and so on. To transfer data over such channel, HomePNA 2.0 uses training sequence to equalize channel and uses FD-QAM optionally as modulation method. So modem receiver demodulate QAM based signal and needs optimum architecture that fully uses these transmission feature. As a result of research, we define 2 mode function of modem receiver depending on TX/RX state. In this paper, particularly, we show the algorithm of equalizer, carrier phase recovery and frame synchromzationblock and propose architecture that improve the performance of channel equalization and is stable in operation. In the end, we estimate the performance of proposed HomePNA2.0 modem receiver over HomePNA TEST LOOP using SPW program.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.7
• /
• pp.30-38
• /
• 2012

This paper presents packet detection, frequency offset estimation architecture and performance analysis for OFDM-based wireless personal area network (WPAN) systems. Packet detection structure is used to find the start point of a packet exactly in WPAN system as the correlation value passes the constant threshold value. The applied autocorrelation structure of the algorithm can be implemented simply compared to conventional packet detection algorithms. The proposed frequency offset estimation architecture is designed for phase rotation process structure, internal bit reduction to reduce hardware size and the frequency offset adjustment block to reduce look-up table size unlike the conventional structure. If the received signal can be compensated by estimated frequency offset through the correction block, it can reduce the impact on the frequency offset. Through the performance result, the proposed structure has lower hardware complexity and gate count compared to the conventional structure. Thus, the proposed structure for OFDM-based WPAN systems can be applied to the initial synchronization process and high-speed low-power WPAN chips.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.9-17
• /
• 2000

In this paper we implement computer simulation system of 4FSK signal MODEM using Quadrature detector and analyze overall tranceiver system. We follow the FLEX wireless paging system standards and construct premodulation filter and data frame. We propose an efficient open loop symbol timing recovery algorithm which takes advantage of 128 bit length preamble pattern and also propose a 32 bit UW pattern which Is based on the optimal UW detection method, and excellent aperiodic autocorrelation characteristic. The BER simulation in the fading channel as well as AWGN is performed with BCH coding and Interleaving to the Quadrature detector system and it is shown that a high coding fain occurs in the fading channel rather than AWGN channel.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.217-222
• /
• 2006

To find a location, GPS has been wildly used. But, it is hard to use in indoor because of very weak signal level. To meet indoor requirements, there have been many studies applying wireless communication networks such as WLAN, UWB and ZigBee. Among these, ZigBee is widely adopted in many WSN applications because it has an advantage of low-power and low-cost. In ZigBee, the RSSI is used as range measurement for ad-hoc network. The RSSI are converted to ranges using the signal attenuation model and these ranges become inputs of positioning methods. The obtained position with RSSI has large error because of its poor accuracy. To overcome this problem, ultrasonic sensors are added in many researches. By measuring the arrival time difference of ZigBee and ultrasound as a range measurement, the precise position can be found. However, there are still many problems: scheduling of beacons to transmit signals in a correct order, addition and synchronization of beacons and low-rate positioning rate. At this paper, an efficient method to solve these problems is proposed. In the proposed method, a node transmits ZigBee and ultrasound signal simultaneously. And beacons find the range with the received signals and send it back to a node with ZigBee. The position is computed in a node with the received ranges. In addition, a new positioning algorithm to solve the risk of the divergence in the linearization method and the singularity problem in the Savarese method is presented. Both static and dynamic experimental results show 0.02m RMS errors with high output rate.

• The KIPS Transactions:PartC
• /
• v.15C no.1
• /
• pp.31-36
• /
• 2008

The clock frequency difference of sensor nodes is one of main parameters in TOF estimation and affect to degrade ranging algorithms to estimate positions of mobile nodes in wireless sensor networks. The specification of IEEE802.15.4a describes asynchronous TWR and SDS-TWR insensitive to frequency difference without any additional network synchronization. But the TWR and SDS-TWR can not eliminate sufficiently the effect of frequency difference of node pair, packet processing delay and its difference. Especially use of low cost oscillator with wide range offset, sensor node with different hardware and software can make the positioning errors worse. We propose an estimation method of frequency differences, and apply the measured frequency differences to TWR and SDS-TWR. We evaluate the performance of the proposed algorithm with simulation, and make certain that the proposed method enhances the performance of existing algorithms with positioning errors less than 25 cm.

• Journal of Advanced Navigation Technology
• /
• v.17 no.6
• /
• pp.609-615
• /
• 2013

As with any ships, adequate power provision is crucial, especially on the ocean navigating ships far from the land. In order to resolve the effective and economic power supply system of any ship in operation, in this paper, we propose a power management system that intelligently controls the power supply in ships. Power management systems in this design consist of a power load detection system, a generator configuration system, and a power monitoring system respectively. The CT / PT sensor is used to measure amount of current and power in the power detection system, and according to the collected information from various sensor, the generator configuration system will switch on and off the main / sub generator effectively. Finally, the power monitoring system will display all status information of this power management system at a glance for users. This power management systems implemented in this paper is evaluated via real-time experiments, which works well as designed, and certified by KSCIEC61892-1:2012 and KSCIEC60950-1:2008.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.10
• /
• pp.1537-1544
• /
• 2022

When designing chip, it considers design specification, timing problem, and clock synchronization on place & route (P&R) process. P&R process is complicated because of considering various factors. Chip uses clock tree synthesis (CTS) to reduce clock path delay. The purpose of this study is to examine shallow-CTS algorithm for checking clock tree synthesizable. Using open source Parser-Verilog, register transfer level (RTL) synthesizable Verilog file is parsed and it uses Pre-CTS and Post-CTS process that is included shallow-CTS. Based on longest clock path in the Pre-CTS and Post-CTS stages, the standard deviation before and after buffer insertion is compared and analyzed for the accuracy of CTS. In this paper, It is expected that the cost and time problem could be reduced by providing a pre-clock tree synthesis verification method at the RTL level without confirming the CTS result using the time-consuming licensed EDA tool.

• Journal of the Society of Disaster Information
• /
• v.19 no.2
• /
• pp.432-438
• /
• 2023

Purpose: The purpose of this study is to enable users to conveniently report risks by automatically classifying risk categories in real time using AI for images reported in the life safety prevention service app. Method: Through a system consisting of a life safety prevention service platform, life safety prevention service app, AI model serving server and sftp server interconnected through the Internet, the reported life safety images are automatically classified in real time, and the AI model used at this time An AI learning algorithm for generation was also developed. Result: Images can be automatically classified by AI processing in real time, making it easier for reporters to report matters related to life safety.Conclusion: The AI image automatic classification system presented in this paper automatically classifies reported images in real time with a classification accuracy of over 90%, enabling reporters to easily report images related to life safety. It is necessary to develop faster and more accurate AI models and improve system processing capacity.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.12 s.91
• /
• pp.1152-1160
• /
• 2004

OFDM technique was adopted as the standard of IEEE 802.1 la and it has been widely used for wireless LAN, European DVB/DAB system, Korean DMB system. In the standard of IEEE 802.11a the data packet is composed of two parts, preamble and data. Preamble is composed of short pilots and long pilots, which are used for synchronization and estimation of frequency offset and channel. We can also compensate phase noise effect in the transceiver by using above pilots. The phase noise is more complicate than frequency offset and seriously affects system performance. In this paper, we newly propose CPE and ICI simultaneous compensation method to compensate phase noise generated by transceiver oscillator and compare with previous studies. As results, phase noise effect can be significantly compensated by CPE cancellation method, PNS algorithm and our proposed CPE and ICI compensation method. Especially, the proposed CPE and ICI compensation method can achieve the best BER performance compared with original OFDM, CPE cancellation method and PNS algorithm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.5
• /
• pp.555-564
• /
• 2016

This paper proposes a time slot allocation scheme for military patrol environments. This proposal comes from analysis of traffic properties in a military patrol environment. In the near future, robots are expected to explore enemy grounds and measure threat, taking the place of human patrol. In order to control such robots, control messages must be extremely accurate. One mistake from the control center could cause a tragedy. Thus, high reliability must be guaranteed. Another goal is to maintain a continual flow of multimedia data sent from patrol robots. That is, QoS (Quality of Service) must be guaranteed. In order to transmit data while fulfilling both attributes, the per-path based centralized TDMA slot allocation scheme is recommended. The control center allocates slots to robots allowing synchronization among robots. Slot allocation collisions can also be avoided. The proposed scheme was verified through the ns-3 simulator. The scheme showed a higher packet delivery ratio than the algorithm in comparison. It also performed with shorter delay time in the downlink traffic transmission scenario than the algorithm in comparison.