• Elastomers and Composites
• /
• v.53 no.3
• /
• pp.124-130
• /
• 2018

Recently, microwaves have been used for desulfurization because they can selectively dissociate C-S and S-S bonds present in vulcanized rubber. In this study, we investigated the changes in structural and physical properties of EPDM (Ethylene propylene diene monomer) rubber by irradiating it with microwaves for different durations. The surface chemical composition of the irradiated EPDM rubber was analyzed by FT-IR, XPS, and EDS analyses. It was confirmed by XPS that C-S and S-S S2p peak heights greatly decreased when microwave irradiation was performed for more than 5 min. In the EPDM sample irradiated with microwaves for 10 min, the number of S-O bonds significantly increased owing to oxidation. As the microwave irradiation time was increased, SEM images showed cracks and voids on the EPDM surface. The 20% decomposition temperature of the EPDM rubber sample was investigated by TGA, and it was found to be about $435.23^{\circ}C$ for the EPDM rubber irradiated for 10 min. The crosslinking density of the EPDM rubber was determined by measuring the degree of swelling, and the highest value was observed for the E5 sample irradiated for 5 min. The degree of swelling of the E10 sample irradiated for 10 min was lower than that of the E5 sample. These results indicate that when irradiated with microwaves for more than a certain time, desulfurization occurs and the side chain of the EPDM rubber dissociates and forms additional crosslinking bonds.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.3
• /
• pp.274-283
• /
• 2014

Swelling of the heat-treated netting for gillnet was estimated through the netting height in square acrylic tank. Experimental Nylon netting and PBSAT netting were heat-treated by using the high-degree vacuum method in hot water after net making. Heat-treatment temperatures were conducted with Nylon netting $105^{\circ}C$ and PBSAT netting $62^{\circ}C$, $65^{\circ}C$, $66^{\circ}C$, $67^{\circ}C$. The swelling measurement method of a netting using the square tank was capable of the reduction measurement errors comparing with measurement methods of a mesh inner angle and the shortening rate of a mesh size. In addition, this method was available to comparison evaluation for each netting more easily. Wet type heat-treatment apparatus with high-degree vacuum was shown higher $7{\sim}8^{\circ}C$ inner side temperature than a setting temperature. The tensile strength and elongation of Nylon netting and PBSAT netting were shown higher wet condition than dry condition. The tensile strengths of PBSAT monofilaments in dry and wet condition were sharply decreased at heat-treatment temp. $75^{\circ}C$ than heat-treatment temp. $74^{\circ}C$.

• Journal of Korean Neurosurgical Society
• /
• v.56 no.5
• /
• pp.436-440
• /
• 2014

Sarcoidosis is a systemic disease of unknown etiology that may affect any organ in the body. The nervous system is involved in 5-16% of cases of sarcoidosis. Here, we report a case of intramedullary sarcoidosis presenting with delayed spinal cord swelling after laminoplasty for the treatment of compressive cervical myelopathy. A 56-year-old woman was admitted to our hospital complaining of upper extremity pain and gait disturbance. The patient had undergone laminoplasty for compressive cervical myelopathy 3 months previously. Follow-up magnetic resonance imaging revealed a large solitary intramedullary lesion with associated extensive cord swelling, signal changes, and heterogeneous enhancement of spinal cord from C2 to C7. Spinal cord biopsy revealed non-necrotizing granulomas with signs of chronic inflammation. The final diagnosis of sarcoidosis was based upon laboratory data, imaging findings, histological findings, and the exclusion of other diagnoses. Awareness of such presentations and a high degree of suspicion of sarcoidosis may help arrive at the correct diagnosis.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.07a
• /
• pp.61-64
• /
• 2003

Optical resolution of a-amino acid (tryptophan and tyrosine) optical isomers was achieved by a pressure driven membrane separation process, using self-supporting crosslinked membranes base on polysaccharide with different swelling indices that ranged from 100 to 70%. The membranes prepared by casting and drying the polymer solution containing 5wt% acetic acid on an acryl plate followed by crosslinking with glutaraldehyde were characterized using such analytical methods as FTIR and swelling index measurements. On the way of separating the optical isomers, several experimental factors such as the concentration of the feed solutions, operating pressure and temperature, and degree of crosslinking of the membranes have been studied. When the chitosan membranes with 70% of swelling index were used , almost complete optical resolution was obtained; 97.92% of enantiomeric excess (ee %) and 2.26 g/$m^2$ㆍh of flux. The operating pressure and the concentration of feed solutions were respectively 1.0 kgf/$\textrm{cm}^2$ and 0.49 mmol/L.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.518-522
• /
• 2012

Hyaluronic acid (HA) microbeads were synthesized by dropping 0.5 wt% of sodium hyaluronate dissolved in NaOH into 0.2 vol% of divinyl sulfone dissolved in 2-methyl-1propanol at a speed of 0.005 ml/min. HA microbeads were collected from a divinyl sulfone crosslinker solution stirred at 200 to 400 rpm for 5 h at temperatures from room temperature to $60^{\circ}C$ at intervals of $10^{\circ}C$. The crosslinked microbeads were then cleaned thoroughly using distilled water and ethanol. SEM results revealed that the microbeads were white-colored spheres. The 3-D porous network structure of the microbeads became dense with an increase in the crosslinking temperature; however, no dependence of the crosslinking temperature on the microbead size was detected. The extent of swelling decreased from 970% to 670% with an increase in the crosslinking temperature from room temperature to $60^{\circ}C$, most likely due to the increase in the degree of crosslinking.

• Textile Coloration and Finishing
• /
• v.31 no.3
• /
• pp.177-186
• /
• 2019

In this study, we investigated for synthetic hydrotalcite in chloroprene rubber foam. Experiments were carried out to find the optimum content ratio by controlling the contents of MgO and Hydrotalcite. Swelling test in toluene immersion was made to measure the crosslinking density of CR foams, and the cure properties were investigated with flat die rheometer and Mooney viscosity. The difference of hardness, tensile strength and elongation at break were observed after immersing in 7% NaCl or 21% NaCl solutions for a day and four days. In addition, the volume change and water content remaining in CR foam were measured after immersing NaCl solution. As content of MgO increased, the value of the cure torque tended to increase, but it was almost constant above 2phr of MgO. However, the Mooney viscosity decreased with increasing MgO content. The crosslinking density, determined by the swelling ratio, showed that the CR compound without MgO showed a higher degree of swelling. When the content of hydrotalcite/MgO was 3:2, it was the lowest volume change of CR form. Also, As the content of hydrotalcite decreased, the difference of mechanical properties before and after immersion NaCl solution increased.

• Textile Coloration and Finishing
• /
• v.14 no.3
• /
• pp.26-33
• /
• 2002

Dyeing properties and crosslinking effect of bifunctional reactive dyes on chitosan fiber were investigated to improve the stability of chitosan fiber against the mild acidic solution and the wet processing. Chitosan fibers were crosslinked with epichlorohydrin for comparing purpose, and dyed with C. I. Reactive Red 194, C. I. Reactive Blue 50, and the reactive dye having two $\alpha$-bromoacrylamide groups at various concentrations. The initial dyeing rates of reactive dyes are rapid and chitosan fibers absorb the relatively large amount of dyes. The chitosan fibers dyed with these dyes show the low degree of swelling and the low solubility in 1 % acetic acid solution and also represent the higher thermal stability The reactive dye with two $\alpha$-bromoacrylamide groups shows higher crosslinking effect than other dyes.

• Korean Journal of Food Science and Technology
• /
• v.17 no.1
• /
• pp.33-36
• /
• 1985

Some properties of starches from three naked barley cultivars(Songhak, Youngsan and Jinan 56) were compared. No significant differences in water-binding capacity, amylose content, relative crystallinity, swelling power and gelatinization degree at various pasting temperatures among cultivars were observed. However, starches showed characteristic viscograph indices and viscosity development patterns in aqueous sodium hydroxide solution. Songhak starch exhibited the lowest pasting temperature and was the most resist to alkali gelatinization.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.69-73
• /
• 2004

A series of $H_3PO_4$-doped composite membranes based on poly(vinyl alcohol)(PVA) and silica have been prepared by sol-gel process. The proton conductivity, as well as properties of swelling, methanol permeation, was measured in this study. The proton conductivity increased with the molar ratio of $H_3PO_4$ to silica. With the silica content increasing, swelling degree decreased and methanol permeability showed a slight increase. It suggested that the former was mainly determined by hydrophilicity of the membrane, while the latter was dominated by the interconnectivity of matrix. According to the value of on, the optimal conformations of these composite membranes were 60, 70, 80 wt.$\%$ of PS-x in membranes, where x were 1.5, 1.0, and 0.5, respectively. These composite membranes were thermal stability up to $200^{\circ}C$.

• Carbon letters
• /
• v.6 no.3
• /
• pp.173-180
• /
• 2005

In this study, AR (aromatic resin) pitch was employed as the matrix-precursor for carbon/carbon composite because it exhibits much higher coke yield than coal tar pitch. As a result, a fabrication process of carbon/carbon composites can be shortened. It has been known that the pitches may cause swolling problem during the carbonization process. In order to restrain the swelling occurrence, a small quantity of carbon black was added to the AR pitch. Due to addition of carbon black the swelling was decreased largely and the perform can be infiltrated with the AR pitch. The densification efficiency of the performs was compared with various matrix-precursors. The coke yield of matrixprecursors, the morphology and the degree of graphitization of carbon matrix were analyzed.