• Carbon letters
• /
• v.4 no.1
• /
• pp.24-30
• /
• 2003

In this study, densified 4D carbon/carbon composites were made from carbon fiber and coal tar pitch through the process of pressure impregnation and carbonization and then followed by carbonization and graphitization. To improve the oxidative resistance of the prepared carbon/carbon composites, the surface of carbon/carbon composites was coated on SiC by the pack cementation method. The SiC coated layer was created by depending on the constitution of pack powder, and reaction time of pack-cementation. The morpology of crystalline and texture of these SiC coated carbon/carbon composites were investigated by XRD, SEM/EDS observation. So the coating mechanism of pack-cementation process was proposed. The oxidative res istance were observed through the air oxidation test, and then the optimal condition of pack cementation was found by them. Besides, the oxidative mechanism of SiC formed was proposed through the observation of SiC coated surface, which was undergone by oxidation test.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.163-164
• /
• 2011

본 연구에서는 Ag paste의 전도성 필러로 사용되는 Ag 파우더를 대체하고자 Ag-coated SnO 파우더가 합성되었다. Ag-coated SnO 파우더의 합성을 위해서는 (1) 균일한 SnO 파우더 합성, (2) SnO 파우더 위에 Ag 무전해도금 과정이 수행 되어야 한다. 본 발표에서는 무전해 도금과정 중 Ag입자의 초기 핵생성 및 성장 관점에서, SnO 파우더의 전처리 조건, 반응 온도 및 pH, 첨가되는 환원제 양의 효과가 조사되었다.

• Korean Journal of Materials Research
• /
• v.7 no.3
• /
• pp.203-212
• /
• 1997

This paper evaluated the feasibility of laser consolidation for improving the properties of the plasma coated layer, Further, the mechanim of the degradation sequence of the chrome carbide layer applied on the turbine blades was postualted. The laser consolidation could be successfully applied for improcing the surface properties of the plasma coated blade, if a proper condition was carefully chosen. The consolidated layer had erosion & corrosion resistance and vond strength superiro to those of the as-plasma coated layer. The properties of the consolidated layer were strongly dependent upon the degree of dilution, especially on the Fe pickup from the substrate. The degradation of the plasma coating layer was thought to be a reault of the repeating action of the solid particle erosion, corrosion penetration through the pores and oxide films formed along the interlayer surface and impact spalling.

• Journal of Environmental Health Sciences
• /
• v.26 no.3
• /
• pp.76-80
• /
• 2000

The purpose of this study is to compare the performance of rubble support media coated perlite and non-coated media. As rubble was coated perlite, the porocity of reactor was increased 5.6%, whereas packing weight was decreased 17.6%. When rubble was coated perlite, microorganisms were attached on the surface of support media after 2 hours. TCOD removal efficiency of the reactor packed with rubble support media coated perlite was higher 4~9% than that of rubble. The end of experiment, MLVSS of rubble support media and rubble coated perlite was 1858.8mg/ι, 2785.9mg/ι, respectively.

• Steel and Composite Structures
• /
• v.21 no.2
• /
• pp.429-442
• /
• 2016

The aim of this paper is to determine temperature and stress distributions in a ceramic based on Partially Stabilized Zirconia coated steel piston crown by using plasma spraying for improving performance of a marine diesel engine. Effects of coating constituent and thickness on temperature and stress distributions were investigated including comparisons with results from an uncoated piston by means of finite element method namely ANSYS. Temperature developed at the coated surface is significantly higher than that of the uncoated piston. The maximum stress components occur between bond coat and adjacent ceramic layer. Provided that coating thickness is constant as 0.5 mm, when numbers of layers increase, magnitude of the normal stress decrease about 34.1% on the base metal surface according to uncoated piston, but the base metal surface temperature of the steel piston increase about 13.1%.

• International Journal of Concrete Structures and Materials
• /
• v.8 no.2
• /
• pp.165-172
• /
• 2014

Recycled coarse aggregate (RCA) made from waste concrete is not a suitable structural material as it has high absorption of cement mortar, which adheres on the aggregate surface and on the tiny cracks thereon. Therefore, when using RCA made from waste concrete, much water must be added with the concrete, and slump loss occurs when transporting. Hence, its workability is significantly worse than that of other materials. In this study, surface of RCA was coated with water-soluble polycarboxylate (PC) dispersant so that its characteristics improved. Each possibility was evaluated: whether its slump loss can be controlled, by measuring its workability based on the elapsed time; and whether it can be used as a structural material, by measuring its strength. Moreover, the carbonation due to cement mortar adhesion was measured through a carbonation test. As a result, RCA coated with PC dispersant was found to be better than crushed coarse aggregate and RCA when the physical properties of the fresh concrete and the mechanical, durability of the hardened concrete were tested.

• Journal of Environmental Science International
• /
• v.8 no.2
• /
• pp.205-209
• /
• 1999

Iron hydroxides are good adsorbents for uncomplexed metals, some metal-ligand complexes and many metal oxyanions. However, their adsorption properties of these precipitations are not fully exploited in wastewater treatment operations because of difficulties associated with their separation from the aqueous phase. This study describes experiments in which iron hydroxides were coated onto the surface of ordinary adsorbents(Sea sand) that are very resistant to acids, The coated adsorbents were used in adsorption of oxyanionic metals. The process was successful in removing some anions such as $SeO_3(-II)$ over a wide range of metal concentrations and sorption of oxyanionic metals increased with decreasing pH. Formation of two surface complexes for oxyanionic metals adsorption on iron hydroxides comprise (1) complexation of the free anion by a positively charged surface site, and (2) protonation of the adsorbed anion (or alternatively adsorption of a protonated form from solution) The coated adsorbents are inexpensive to prepare and could serve as the basis of a useful oxyanionic metal removal.

• Journal of environmental and Sanitary engineering
• /
• v.10 no.3
• /
• pp.78-84
• /
• 1995

Cationic surfactants can be used to modify surface of solids to promote adsorption of hydrophobic organic compounds. This behavior is due to the surfactant forming aggregate structure on the solid surface. Partition coefficients are commonly used to quantify the distribution of organic pollutants between the aqueous and particulate phases of aquatic system Partitioning of hydrophobic compounds to cetyltrimethylammonium bromide ( CTAB ) coated silicate has been investigated as a function of surfactant surface coverage at I=0 and 0.1 ionic strength. Toluene, Xylene, TCI sorption experiments demonstrated that the CTAB coated silicate was able to remove these hydrophobic organic compounds from solution The hydrophobic organic compound with the higher Kow had higher removals than lowest Kow hydrophobic organic compound.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.179-179
• /
• 2009

For the deposition of the semiconductor nanocrystals or quantum dots, it is required to have the substrates with smooth surface roughness. Slot-die coating method wad adopted and optimized varying the processing parameters like coating speed, gap distance, solution concentration, etc to get the smooth coated films on flexible substrates. The coating speed in slot-die method was varied from 1 m/min to 2.5 m/min focusing especially on its industrial usage. The gap distance between the substrate surface and slot-die lip was changed also to control mainly the thickness of coated films.

• Journal of Powder Materials
• /
• v.18 no.6
• /
• pp.546-551
• /
• 2011

Ag spot-coated Cu nanopowders were synthesized by a hydrothermal-attachment method (HA) using oleic acid capped Ag hydrosol. Cu nano powders were synthesized by pulsed wire exploding method using 0.4 mm in diameter of Cu wire (purity 99.9%). Synthesized Cu nano powders are seen with comparatively spherical shape having range in 50 nm to 150 nm in diameter. The oleic acid capped Ag hydrosol was synthesized by the precipitation-redispersion method. Oleic acid capped Ag nano particles showed the narrow size distribution and their particle size were less than 20 nm in diameter. In the case of nano Ag-spot coated Cu powders, nanosized Ag particles were adhered in the copper surface by HAA method. The components of C, O and Ag were distributed on the surface of copper powder.