• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1254-1260
• /
• 2000

There have been many developments in super precision working technique and working method up to, now. But, it is very difficult to evaluate working surface accurately without the technicians experience and judgment. Surface roughness tester using stylus was used to measure surface condition generally But this method is not so desirable because of damage on test piece caused by contact between the workpiece and the stylus sensor. As a result, non-contact method was known as a good way to carry, out this process without damage. However, this is a difficult one among the various measuring methods. So we are tying to suggest a new method using texture analysis through image processing to get a surface information in worked test piece. Co-occurrence matrix using difference of gray levels between a pixel and its neighboring one was used to study behavior of surface roughness and to J acquire data for analysis. Standard specimen was adapted to verify this research. We suggest texture information method in order to evaluate surface state for the best measurement system.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.4
• /
• pp.211-219
• /
• 2002

In this study, in-situ performance test of a wet surface finned-tube evaporator of an air source heat pump which has a rating capacity of 20 RT is carried out. Since test conditions, such as indoor and outdoor air conditions cannot be controlled to satisfy the standard test conditions, experiments are done with the inlet air conditions as they exist. From the experimental data, air side heat and mass transfer coefficients were calculated by the well known heat and mass transfer analogy and tube-by-tube method. Since current procedure underpredicted the experimental sensible heat factor (SHF), a proper empirical parameter was introduced to predict the experimental data with satisfactory results. This study provides the method of evaluating the heat and mass transfer coefficients of a wet surface finned-tube evaporator of which in-situ performance test is necessary.

• Journal of Advanced Navigation Technology
• /
• v.10 no.4
• /
• pp.299-305
• /
• 2006

DURUMI-II is developed into test bed airplane for the multi-purpose flight test. It satisfied the civil aeronautics law. DURUMI-II is equipped with Airborne System for acquiring of flight test data and can fly by oneself. In this paper, the redundancy of DURUMI-II control system is operated sequentially is explained. The divided control surface and the requiring program method for flight test are described. Also, it is described that the exact control input is applied using the new method. Finally, the results of flight test for new method are analyzed.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2007.06a
• /
• pp.237-240
• /
• 2007

The evaluation of shear modulus (or shear wave velocity) profile of site is very important in the various fields of geotechnical engineering. To obtain shear wave velocity profile, various in-situ seismic methods using surface waves have been developed. These surface wave based in-situ seismic methods have their own strength and weakness. In this study, new seismic site characterization method using the harmonic wavelet analysis of wave (HWAW) was proposed to overcome some of weaknesses in the existing surface wave based seismic site characterization methods. HWAW method which is based on time-frequency analysis using harmonic wavelet transform have been developed to determine phase and group velocities of waves. In order to estimate the applicability of HWAW method, field tests were performed. Through field applications and comparison with other test results, the applicability of the proposed method were verified.

• Bulletin of the Korean Space Science Society
• /
• 2004.10b
• /
• pp.254-257
• /
• 2004

Both ground and space telescopes are being built larger and larger. Accordingly, the secondary mirrors become larger which are convex mostly on the surface form. Testing convex mirrors becomes more difficult and delicate than testing concave mirrors in optics, because additional optical components are needed to make the reflected rays converge. Hindle type tests are frequently used for measuring the surface deforms of convex mirrors, which employs a meniscus lens to reverse the diverted rays from the mirrors. In case of testing large convex mirrors by using Hindle type tests, attention would be needed as larger meniscus lens is required. A method of modified Hindle test has been studied and the characteristics are analyzed. In this paper, current method of testing convex mirrors is presented, and a new method is discussed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.8
• /
• pp.1128-1133
• /
• 2014

Most of the statistical signal analysis processed in the time domain and the frequency domain are based on the assumption that the signal is weakly stationary(wide sense stationary). Therefore, it is necessary to know whether the surface EMG signals processed in the statistical basis satisfy the condition of the weak stationarity. The purpose of this study is to find optimal segment length of surface EMG signal for assessing stationarity with the modified Run-test and RA-test. Ten stationary surface EMG signals were simulated by AR(autoregressive) modeling, and ten real surface EMG signals were recorded from biceps brachii muscle and then modified to have non-stationary structures. In condition of varying segment length from 20ms to 100ms, stationarity of the signals was tested by using six different methods of modified Run-test and RA-test. The results indicate that the optimal segment length for the surface EMG is 30ms~35ms, and the best way for assessing surface EMG signal stationarity is the modified Run-test (Run2) method using this optimal length.

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.3
• /
• pp.353-362
• /
• 2009

A new method and equipment for measuring the zeta potential of the external surface of hollow fiber (HF) membranes is reported. An existing commercial streaming potential analyzer in conjunction with home-made test cells was used to determine the electrokinetic surface characteristics of various HF membranes. It was shown that measurements of the external surface of HF membrane using the home-made test cells designed in this study were easy and reliable. The zeta potential values were quite accurate and reproducible. By varying the physical shape of the test cells to adjust hydrodynamics inside the test cells, several upgrade versions of home-made test cells were obtained. It was shown that the zeta potential of the external surface of HF membranes was most influenced by membrane materials as well as the way of surface modification. However, the overall surface charge of tested HF membranes were much less than that of commercial polyamide thin-film-composite (TFC) reverse osmosis (RO) membranes due to the lack of surface functional groups. For the HF membranes with the same material, the effect of pore size on the zeta potential was not significant, implying the potential of accurate zeta potential measurements for various HF membranes. The results obtained in this study are expected to be useful for better understating of electrokinetic surface characteristics of the external surface of HF membranes.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2009.09a
• /
• pp.59-64
• /
• 2009

The propeller induced forces acting on a hull are surface forces and bearing forces. The bearing forces are the forces acting directly on the propeller which are transferred to the hull through the propeller bearings. The surface forces are those which act by fluid pressure directly on the various hull surfaces. Because the surface force is main source to oscillate stern constructions and deckhouse, the estimation of surface force is very important to predict response of forced vibration of that. The estimation methods were statistical analysis method, theoretical analysis method and method through model test.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.37 no.1
• /
• pp.16-22
• /
• 2021

Purpose: The purpose of this study is to investigate the effect of surface polishing and fabrication method on the flexural strength of temporary restorative resin. Materials and Methods: Each of four fabrication methods was used to make 30 temporary restorative resin specimens and the specimens were divided into two groups depending on whether they were polished by mechanical polishing. Specimens were stored in 37℃ thermostat for 24 hours. Flexural strength was measured using a universal testing machine (UTM). The data obtained through the experiment were analyzed with Two-way ANOVA, Tukey's HSD test and Paired t-test. Results: CAD/CAM milling group showed the highest flexural strength regardless of surface polishing. In decreasing order, the flexural strength of the other fabrication method group was as follows SLA 3D printing, DLP 3D printing, and Conventional method group. Conclusion: Surface polishing did not affect flexural strength of the temporary restorative resin (P > 0.05). However, there were statistically significant differences in flexural strength depending on fabrication method (P < 0.05).

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.1
• /
• pp.40-45
• /
• 2004

Recently, aspheric optical lenses and mirrors, which are harder to manufacture and measure than the conventional spherical ones, are widely used, particularly in electronic fabrication process. Generally, interferometric optical method is used for the measurement of spherical optical surface. However, the interferometric method for aspheric surface measurement is difficult because it needs a precise null corrector and strict environmental conditions such as constant temperature, humidity and vibrations. We have been studied on the manufacturing of aspheric optics to improve the surface profile accuracy and productivity using a corrective polishing process. For the corrective polishing, a practical method of On-Machine Measurement (OMM) is required. For this purpose, an optical OMM system has been studied using the Shach-Hartmann test, which is very robust to the practical polishing environment. The wavefront has been reconstructed from the measured data using the primary aberration polynomial function by the least squares fitting. The measured result of the OMM system shows that the maximum deviation is less than 200 nm for the one of commercial Fizeau interferometer Wyko 6000.