• 한국전기전자재료학회논문지
• /
• 제15권6호
• /
• pp.504-510
• /
• 2002

Recently, thin film capacitors of high dielectric constant and low leakage current are applied to integrated devices. In this study, (Ba, Sr)$TiO_3$ (BST) thin films for low cost were prepared by Sol-Gel method. BST solution was spin-coated on Pt/$SiO_2$/Si substrate at 4,000 rpm for 10 seconds. Coating process was repeated 3 times and then sintered at $700^{\circ}C$ for 30 minutes. Structural and electrical characteristics of each specimen were analyzed by TG-DTA, SEM, fractal phenomenon, voltage-current and dielectric factor. Thickness of BST ceramics thin films are about 2,600~2,800 ${\AA}$ at depositing 3 times. Dielectric constant of thin films was decreased in 1 kHz~1 MHz. Dielectric constant and loss to frequency were 250 and 0.02 in $(Ba_{0.7}Sr_{0.3})TiO_3$ (BST3). Leakage current of BST3 was $10^{-9}\sim10^{-11}$/ A under 3 V.

• 한국전기전자재료학회논문지
• /
• 제29권1호
• /
• pp.40-43
• /
• 2016

Transparent color coating films were fabricated on a glass substrate by using sol-gel hybrid binder and organic dye. Sol-gel hybrid binder coating film fabricated with PTMS of 0.03 mole showed a very high pencil hardness of 9 H. As the withdrawal speed increased from 1.0 mm/s to 5.0 mm/sec, The yellowness ($b^*$) of coating glass also gradually increased. The transmittance of yellow color coating glass was 82.6% and the haze of coating glass was 0.35%. Red and blue color coating glasses also showed the high transmittance of 62.4% and 80.6% respectively. The surface hardness of color coating films was 6 H.

• 한국환경과학회지
• /
• 제30권6호
• /
• pp.501-505
• /
• 2021

V₂O₅-TiO₂ catalysts were prepared by various methods. V₂O₅-TiO₂ were prepared by sol-gel method with different drying conditions (aerogel and xerogel), and V₂O₅ supported on TiO₂ obtained by sol-gel method with precipitation-deposition method and impregnation method. The performance of the V₂O₅-TiO₂ catalysts was investigated for the selective oxidation of hydrogen sulfide in the stream containing both ammonia and excess water. All the catalysts showed good dispersion of vanadium and they had high H₂S conversion with no or little production of sulfur dioxide. The V₂O₅-TiO₂ aerogel catalyst prepared by sol-gel method with drying under super critical condition had the highest surface area which led to better catalytic activity compared to those by other synthesis methods.

• Corrosion Science and Technology
• /
• 제22권6호
• /
• pp.447-456
• /
• 2023

In this work, we performed a comparative study examining two coatings on Ti Gr.1 for use in fuel cell bipolar plates. The coatings consisted of carbon black as the conductor along with acrylic polymer and Ti Sol-Gel binder as the binder. Ti Sol-Gel that had precipitated as TiO₂ in areas impregnated between carbon black gaps, thereby acting as a binder for carbon black and serving as a polymer coating. Neither of the coatings peeled off during the 90° bend test to check formability. The contact resistance of the TiO₂ coating was found to be lower than that of the polymer binder coating. Moreover, due to coating shrinkage (denser) that occurred during the heat treatment process, the TiO₂ binder coating showed almost the same level of corrosion resistance, as measured by potentiostatic and EIS tests, despite being thinner than the polymer coating. However, both the polymer binder coating and the TiO₂ binder coating had many pores and irregularities internally (around 10 ~ 100 nm) and on the surface (0.1 ~ 2 ㎛). We considered that these pores and irregularities contributed to the lower corrosion resistance.

• Transactions on Electrical and Electronic Materials
• /
• 제17권2호
• /
• pp.109-112
• /
• 2016

We demonstrated an alternative electrically controlled birefringence liquid crystal (ECB-LC) system with ion beam (IB)-irradiated yttrium gallium oxide (YGaO) alignment films using a sol-gel process. The surface roughness of the films was dependent on the annealing temperature; aggregated particles on surface were observed at lower annealing temperatures, whereas a smooth surface could be obtained with higher annealing temperatures. Higher transmittance in the visible region was observed at higher annealing temperatures. The film had an amorphous crystallographic state irrespective of the annealing temperature. Furthermore, ECB-LC cell with our IB-irradiated YGaO film yielded faster response time when compared to ECB-LC cell with rubbed polyimide. Considering the fast response time and high transmittance, the IB-irradiated YGaO-base LC system is a powerful alternative application for the liquid crystal display industry.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2003년도 추계학술발표회초록집
• /
• pp.69-70
• /
• 2003

• Bulletin of the Korean Chemical Society
• /
• 제17권8호
• /
• pp.696-699
• /
• 1996

Silicate and borosilicate gels were prepared by the sol-gel process and thermally treated in the 150-850 ℃ temperature range. Solid-state 1H MAS and 29Si CP/MAS NMR spectroscopy were used to investigate the effects of heat treatments on the silicate gel to glass conversion process. The 1H NMR isotropic chemical shifts and the relative intensities of hydrogen bonded and isolated silanol groups have been used to access the information concerning the dehydration process on the silicate gel surface. The 29Si NMR isotropic chemical shifts affected by the local silicon environment have been used to determine the degree of crosslinking, i.e. the number of siloxane bonds. These NMR results suggest that the silicate gel to glass conversion process is occurred by two stages which are dependent on the temperature; (1) the formation of particles up to 450 ℃ and (2) the formation of large particles by aggregation of each separated single particle above 450 ℃. In addition, the effects of B atom on the formation of borosiloxane bonds in borosilicates have been discussed.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.135-135
• /
• 2003

This paper presents the preparation of SnO$_2$ films by Sol-Gel process and using spin coating method, and their sensing properties in CO gas. Experimental procedure consisted of following steps: (1) Tin chloride(SnCl$_4$) and Ammonium hydrogen carbonate (NH$_4$HCO$_3$) were used as precursors; (2) the Sol solution with concentration of about 10wt% SnO$_2$ was prepared from washed Gel-precipitate for spin coating step; (3) thereafter, the coating solution was dropped onto the alumina (Al$_2$O$_3$) substrate that was then spun, the spin coating was carried out with total 10 times; (4) finally, the films were calcined for 3 hours at 50$0^{\circ}C$ or higher temperature (600, 700, 800 or 90$0^{\circ}C$) in order to obtain various gram sizes. The average grain size was calculated by Scherrer's equation using main peaks in XRD spectra; meanwhile the thickness, microstructure and surface morphology of the films were observed by FE-SEM.

• 한국재료학회지
• /
• 제25권4호
• /
• pp.209-213
• /
• 2015

Synthesis of nano-silica using water glass in a Sol-Gel process is one of several methods to manufacture nano-silica. In nano-silica synthesized from water glass, there are various metal impurities. However, synthesis of nano-silica using water glass in a Sol-Gel process is an interesting method because it is relatively simple and cheap. In this study, nano-silica was synthesized from water glass; we investigated the effect of pH on the synthesis of nano-silica. The morphology of the nanosilica with pH 2 was flat, but the surface of the nano-silica with pH 10 had holes similar to small craters. As a result of ICP-OES analysis, the amount of Na in the nano-silica with pH 2 was found to be 170 mg/kg. On the other hand, the amount of Na in the nano-silica with pH 10 was found to be 56,930 mg/kg. After calcination, the crystal structure of the nano-silica with pH 2 was amorphous. The crystal structure of the nano-silica with pH 10 transformed from amorphous to tridymite. This is because elemental Na in the nano-silica had the effect of decreasing the phase transformation temperature.

• 한국세라믹학회지
• /
• 제42권1호
• /
• pp.7-10
• /
• 2005

[ $TiO_{2}-ZrO_{2}$ ] powders were successfully synthesized by the sol-gel process using titanium iso-propoxide as a precursor. The amorphous $TiO_{2}$ particles, 70 nm in size, homogenously adhered to the surface of $ZrO_{2}$ the powders. After calcination at $450^{circ}C$, most of the $TiO_{2}$ powders appeared as an anatase type, whereas they changed to a rutile phase at $750^{circ}C$. For comparison of photocata­lytic activity, $TiO_{2}-ZrO_{2}$ nano-sized powders calcined at $450^{circ}C,\;600^{circ}C,\;and\;750^{circ}C$ were used. In the $TiO_{2}-20wt\%$ $ZrO_{2}$ powders cal­cined at $450^{circ}C$, there was excellent removal efficiency of Methyl Orange (MO). For the calcination temperature increased, $TiO_{2}­ZrO_{2}$ nano-sized powders increased $ZrO_{2}$ contents showed the good photoactivity for the photooxidation of MO.