• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.16 no.6
• /
• pp.93-107
• /
• 2013

Construction of an artificial wetland for the growth of Sphagnum palustre with emergent macrophytes (Phragmites australis, Typha angustifolia, and Zizania latifolia) was firstly tried and the growth of those plant components according to various environmental combinations has been monitored for three years. Above-ground dry weight of Z. latifolia ($1,500g/m^2$) was higher than T. angustifolia ($900g/m^2$) and P. australis ($500g/m^2$) under most environmental conditions. In overall, planted emergent macrophytes seemed to prefer polishing sand without moss peat as a substrate and relatively deep water-depth condition (20cm) rather than shallow water-depth (5cm). Despite of high calcium content in inflow water (> 15ppm) into the constructed wetland, S. palustre populations have survived in most experimental plots during the monitoring period. Substrate layer including moss peat with high surface-area might play a role as an ion-filter. After three years, relatively thicker litter-layer in Z. latifolia plots due to vigorous growth appeared to heavily depress S. palustre by physical compressing and complete shading processes. Most of all, for the continuous growth of S. palustre, physio-chemical characteristics of water and substrate must be carefully managed. In addition, companion emergent species should be also cautiously selected not to depress S. palustre by much litter production. We suggest P. australis and T. angustifolia as companion species rather than Z. latifolia.

• Journal of the Korean Solar Energy Society
• /
• v.28 no.3
• /
• pp.60-66
• /
• 2008

This study is to investigate an optimal size and position of PV system for apartment complex through the electrical load matching analysis. The 4 types of arrangements of apartment buildings are considered as follows; ㅡtype, alternative ㅡtype, ㄱtype and ㅁtype. We assume that the studied site is composed of 9 buildings. Firstly, solar access evaluation of roof and facade in apartment buildings was performed with the hourly simulations of total received insolation on each surface considering the shading effect of buildings. Electrical load profile of typical Korean apartments were investigated for the load matching analysis. To calculate an annual total PV output, we used MERIT program which is a hourly based load matching tool developed by ESRD. TRY weather data of Daejeon are applied for this analysis. Result shows that approximately 11% of total electric load of the site can be supplied by the PV system in the case of full installation of PV system at the whole south-face roof area of 9 buildings in this stuided apartment complex. Depending on a various installation option of roof and facade area, the possible ratio of PV supply in total electrical load varies from 9% to 42%. Among the 4 arrangement types, the ㅡtype revealed the best option for the maximum output of PV system.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.906-911
• /
• 2008

Because the perimeter of buildings is strongly influenced by solar and the outdoor air temperature, the area has different environmental properties compared to the interior of a building, as in summer heat gain, and in winter heat loss. In particular, if the external wall is glass, the characteristics of the glass material make it pervious to outside conditions, thereby making big changes to the thermal environment. By combining shading device and the efficient exhaust system, an energy saving can be achieved compared to no air barrier systems. The simplified air barrier system is developed with the idea that energy could be conserved by carefully and effectively blowing out the air caught between the glass surface and the roller blind. The way it is configured is therefore by making the roller blind's air-path, and by placing the air output ducts in the most optimum positions. This simplified air barrier system will give improvement in the thermal environment of the parameter area that is strongly affected by solar and the outdoor condition.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.364-369
• /
• 2011

Recently, the cases of BIPV(Building-integrated Photovoltaic) have been increased with interest in renewable energy application for buildings. PV System in building can perform a variety of roles as an energy supplier, exterior materials, aesthetic element and etc. To apply PV modules in buildings, various factors should be considered, such as the installation angle and orientation of PV module, shading, and temperature. The temperature of PV modules that are attached to building surfaces especially is one of the most important factors, as it affects both the electrical efficiency of a PV module and the energy load in a building. BIPV modules designed as finished material for spandrels are presented in this paper. The purpose of this study is to analysis on the thermal performance characteristics of BIPV modules. This study dealt with different types of BIPV modules depending on the backside material, such as clear glass and backsheet. The analysis of monitoring data shows that the PV module temperature was closely related to the solar radiation on the BIPV module surface, and the BIPV used at the backside also had an effect on the PV module temperature that in turn determines its thermal performance.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.5
• /
• pp.157-162
• /
• 2020

In the existing photovoltaic generation system, the system equipped with the reflecting plate is a method in which solar energy (insolation) is concentrated on the surface of the photovoltaic module. However, the solar energy (insolation) lost by being reflected back through the solar module is not considered. Although a method of increasing the amount of power generated by installing a reflector around the solar modules has been proposed, this affects the power generation degradation caused by the shading of other solar modules. Therefore, in order to improve this problem, in this paper, 1) without affecting the development of photovoltaic module according to the shade, 2) photovoltaic module using a reflector rotating the solar energy (insolation) lost by the solar module Study and suggest how to join again. Therefore, the loss of solar energy (insolation) can be minimized through the method of recycling the solar energy according to the countless reflection angle of the lost solar energy (insolation). As a result, it is possible to increase the amount of power generation of the photovoltaic generation system by maximizing the amount of power generation for the same solar radiation.

• Journal of the Korean Solar Energy Society
• /
• v.38 no.2
• /
• pp.45-53
• /
• 2018

For the preliminary step for estimating the performance of roof-type photovoltaic system in urban areas, we analyzed the solar radiation reduction ratio by shadow effect by buildings using DSM (Digital Surface Model) and GIS (Geographical Information System) tools. An average loss by the shadow is about 19% in Seoul. The result was related to the building density and distribution. Monthly results show that the winter season (December and January) was more affected by the shading than during the summer season (June and July). It is expected that useful empirical formulas can be made if more detailed correlation studies are performed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.8
• /
• pp.1709-1715
• /
• 2005

This paper describes the development of 3-D web graphic library for dynamic web graphic design. The 3-D web graphic library developed in this per supports creation of 3-D objects like cube and sphere objects, elimination of hidden line and surface, and the shading of diffuse and specular reflections. It provides, in drawing, perspective projection of an object depth first sort of multiple objects, and wire frame and solid models. It also supports texture mapping function for realistic and dynamic web application in application software. Each created 3-D object gives functions for the scaling, translation, and rotation of itself. It can be used for the development of dynamic web application software and the advertisement of information for business and tourism as a 3-D web graphic library engine. It is written in 'Java' language and runs on web browsers with Java virtual machine without any dependancy of client computer system.

• Journal of Biomedical Engineering Research
• /
• v.19 no.2
• /
• pp.189-198
• /
• 1998

3D medical image reconstruction techniques are useful to figure out complex 3D structures from the set of 2D sections. In the paper, 3D medical image reconstruction system is constructed under PC environment and programmed based on modular programming by using Visual C++ 4.2. The whole procedures are composed of data preparation, gradient estimation, classification, shading, transformation and ray-casting & compositing. Three speed optimization techniques are used for accelerating 3D medical image reconstruction technique. One is to reduce the rays when cast rays to reconstruct 3D medical image, another is to reduce the voxels to be calculated and the other is to apply early ray termination. To implement 3D medical image reconstruction system based on PC, speed optimization techniques are experimented and applied.

• Journal of the Korean Solar Energy Society
• /
• v.40 no.3
• /
• pp.43-52
• /
• 2020

By blocking irradiance, shadows cast by high-rise buildings in urban areas can reduce the power generation efficiency of PV panels installed on low-rise buildings. As the conventionally installed PV panel is not suitable for the urban environment, which is unfavorable for power generating, a more radical solution is required. This study aims to help solve this problem by estimating the optimal PV panel angle. Using the proposed method, the optimal PV angle was calculated by considering shadows that could be cast by nearby buildings throughout the year, and the correlation between solar shading and elevation angle was discovered based on the calculated data.

• Journal of Aerospace System Engineering
• /
• v.16 no.5
• /
• pp.86-93
• /
• 2022

Generally, a deployable solar panel is used primarily to achieve sufficient power output to perform the mission. However, temperature distribution on the antenna reflector may increase due to the shading effect induced by the presence of the deployable solar panels. Appropriate thermal design is critical to minimize the thermal deformation of the mesh antenna reflector in harsh on-orbit thermal environments to ensure remote frequency (RF) performance. In this paper, we proposed a dual-surface primary reflector consisting of a mesh antenna and a flexible fabric membrane sheet. This design strategy can contribute to thermal stabilization by using a flexible solar panel on the rear side of membrane sheet to reduce the temperature distribution caused by the deployable solar panel. The effectiveness of the mesh antenna design strategy investigates through on-orbit thermal analysis.