• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.2
• /
• pp.179-188
• /
• 2011

Steel structures have been allowed to have fatigue damage tolerance in fact. If it would be assessed whether fatigue crack is growing or not and How fast fatigue crack is propagating, we should make a rational decision on methods and a period of reinforcement in the maintenance. In this study, fatigue crack growth tests on two kinds of through-thickness cracked steel plates and a out-of-plane gusset welded joint were conducted to evaluate fatigue crack growth rate using the COD(Crack Opening Displacement), and COD measurement using strain gauges was examined to offer a practical method. As a result, we proposed a reasonable assessing method for fatigue crack growth rate using the COD and it was experimentally proved practical to estimate the COD through measuring strains.

• Explosives and Blasting
• /
• v.21 no.2
• /
• pp.21-30
• /
• 2003

Currently, the shotcrete used as basic support in the tunnel excavation, has the advantages of maintaining high-level strength in condition of early shooting with thin thickness based on the excavation characteristics of rock mass. Therefore supreme equipment and materials were developed and the great strides have continued. Also, the development of measurement technology and the rocks behaviors of undergound are evaluated in detail and the designs of strength and thickness are made. The reinforcement materials development of new material is carried on. Most of the coal fly ash produced in Korea fire power plant is fly ash and bottom mash. Fly ash has been producing to be applied in many fields such as cement, aggregate, construction, civil, agriculture and fisheries. Also a lot of experiments are actively on the way. Therefore in this experiment, in order to use the fly ash mixed with concrete as a material of shotcrete, the experiment was performed in the best content to reduce the compression strength and the shooting rebound ratio of the excavated surface to use fly ash as a substitute material of concrete. As a result, when 15%.wt substitution was made to the fly ash, about 10% of compression strength and 6% of rebound ratio was reduced.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.4
• /
• pp.1-8
• /
• 2012

A Fiber Bragg Grating (FBG) sensor imbedded small wind turbine blade was manufactured to experimentally investigate the feasibility to embed FBG sensors between layers of glass fiber to monitor dynamic strains of the wind turbine blade. The blade which is similar to a commercial 300 W wind turbine blade was manufactured with glass fiber as a reinforcement and epoxy resin as base material. A total of five FBG sensors including one temperature sensor were imbedded in the blade to sense mechanical strain and temperature. While manufacturing the blade, residual strain and temperature that occurred in the small wind turbine blade were monitored using the imbedded FBG sensor array. To examine the sensor performance, an impact test was carried out. The experimental results from the FBG sensors were close to those from electrical strain gages mounted on the blade root surface. The mode shapes of the blade were analyzed also using a commercial Ansys simulation with a model obtained from a three dimensional laser scanning of the blade.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.6
• /
• pp.75-83
• /
• 2014

Heat loss through windows and doors occupies 20 to 45% of the total heat loss in building. It accounts for a large proportion of the total heat loss in building. In order to suppress the amount of heat flow through the windows and doors were considered actions such as reinforcement of insulation performance of window, adoption of low-e glass, and installation of solar heat shading device. The Purpose of this study is to compare solar heat shading performances of 3 types of internal blinds in the summer. In order to verify the solar heat shading performances of the blinds, a roll blind, blind A(Venetian blind) and blind B(Daylight guiding venetian blind)were installed in the four rooms with the same environmental conditions. As a result of the experiment, the blind B, blind A, roll blind showed an excellent performance in that order. Its because the blind B is made of aluminum materials coated with special paints on surface. It doesn't converted to long wave by short wave light. and it is reflected to short wave to outside.

• Journal of Adhesion and Interface
• /
• v.14 no.2
• /
• pp.75-81
• /
• 2013

Epoxy matrix based composites were fabricated by adding SiC nano fillers. The interfacial properties of composites were varied with different shapes of SiC nano fillers. To investigate the shape effects on the interfacial properties, beta and whisker type SiC nano fillers were used for this evaluation. The dispersion states of nano SiC-epoxy nanocomposites were evaluated by capacitance measurements. FE-SEM was used to observe the fracture surface of different structures of SiC-epoxy nanocomposites and to investigate for reinforcement effect. Interfacial properties between carbon fiber and SiC-epoxy nanocomposites were also evaluated by ILSS (interlaminar shear strength) and IFSS (interfacial shear strength) tests. The interfacial adhesion of beta type nanocomposites was better than whisker type.

• Corrosion Science and Technology
• /
• v.7 no.5
• /
• pp.269-273
• /
• 2008

It is known that the fluoric resin has the most outstanding properties in the extremely acidic environment of high temperature. However, this resin is the thermal hardening type that needs long time heat treatments above $250^{\circ}C$. It's impossible to use in situ in the extremely acidic environment such as a huge FGD ductworks or industrial chemical tanks. Furthermore, even the natural hardening type fluoric coatings which can be hardened less than $120^{\circ}C$ can not be applied to the highly acidic environmental plants because of its chemical resistance. In this study, new fluoric coatings that has excellent thermal resistance, chemical resistance and corrosion resistance has been developed in order to solve above problems and to be applied to the large plant structures in the field. These newly developed coatings are organic and inorganic composite type that have fluoric rubber(100 wt%), fluoric resin(5~50 wt%), oxalates(5~30 wt%), inorganic fillers mixed with plate-type and bulk-type solids(20~150 wt%), hardeners(0.5~5 wt%), and hardening hasteners(0.1~3 wt%). The best chemical and physical properties of these coatings are acquired by variation of adhesive reinforcement agents, dispersants, leveling agents. Mixing ratios of plate-type and bulk-type inorganic fillers influence the thermal properties, abrasive resistance and chemical infiltration properties of coatings. The mixing control is also very important to have homogeneous surface and removing inner voids of coatings.

• PNF and Movement
• /
• v.16 no.1
• /
• pp.59-66
• /
• 2018

Purpose: This study aimed (1) to identify asymmetry observed in electromyography (EMG) activity patterns of lower limb muscles between affected and unaffected sides of stroke patients during sit to stand (STS) movement and (2) to identify the muscles of the paretic lower limb that affected STS performance in stroke patients. Methods: This study consisted of 27 patients (15 males and 12 females) with poststroke hemiparesis. The activation of the rectus femoris (RF), tibialis anterior (TA), and gastrocnemius (GCM) of the affected side and unaffected side during STS movement were recorded using surface EMG. In addition, EMG lower limb muscle activation patterns were measured in the all section, pre-thigh off (pre-TO), and post-thigh off (post-TO) section. All measurements were obtained during five repetitions of the STS (FTSTS) movement. An independent t-test was performed to compare the affected side and unaffected side of the lower limb during the STS movement. A stepwise linear regression analysis was conducted to identify the muscles that affected STS performance. Results: Activation of both the RF and TA significantly affected the lower limb during the STS movement (p<0.05). Two muscles showed a difference on the post-TO section. The results of the stepwise multiple regression analysis showed that the RF and TA muscles of the affected lower limb were affected in FTSTS. Conclusion: These results provide a basis for reinforcement training, focusing on the RF and TA muscles of the affected side of stroke patients to improve asymmetric movement and performance in STS movement.

• Composites Research
• /
• v.25 no.3
• /
• pp.76-81
• /
• 2012

Atmospheric pressure plasma treatment on carbon nanotube (CNT) surfaces was performed to modify reinforcement effect and interfacial adhesion of carbon fiber reinforced CNT-phenolic composites. The surface changes occurring on CNT treated with plasma were analyzed by using Fourier transform infrared spectroscope (FT-IR). The significant improvement of wettability on CNT was confirmed by static contact angle test after plasma treatment. Such plasma treatment resulted in a decrease in the advancing contact angle from $118^{\circ}$ to $60^{\circ}$. The interfacial adhesion between carbon fiber and CNT-phenolic composites increased by plasma treatment based on apparent modulus test results during quasi-static tensile strength. Furthermore, the proposed database offers valuable knowledge for evaluating interfacial shear strength (IFSS).

• Journal of Periodontal and Implant Science
• /
• v.36 no.1
• /
• pp.69-84
• /
• 2006

Reports on the comparison of clinical effect between non-surgical and surgical therapy, and the change of the clinical parameters during maintenance phase have been rarely presented in Korea. This study was to observe the clinical changes during maintenance phase of 6 months in patients with chronic periodontitis treated by non-surgical or surgical therapy in Department of Periodontics, Chonnam National University Hospital. Among the systemically healthy and non-smoking patients with moderate to severe chronic periodontitis, twenty eight patients (mean age: 47.5 years) treated by non-surgical therapy (scaling and root planning) and nineteen patients (mean age: 47.3 years) treated by surgical therapy (flap surgery) were included in this study. The periodontal supportive therapy including recall check and oral hygiene reinforcement was started as maintenance phase since 1 month of healing after treatment. Probing depth, gingival recession. clinical attachment level and tooth mobility were recorded at initial, baseline and 1, 2, 3 and 6 month of maintenance phase. The clinical parameters were compared between the non-surgical and surgical therapies using Student t-test and repeated measure ANOVA by initial probing depth and surfaces. Surgical therapy resulted in greater change in clinical parameters than non-surgical therapy. During the maintenance phase of 6 months, the clinical effects after treatment had been changed in different pattern according to initial probing depth and tooth surface. During maintenance phase, probing depth increased more and gingival recession increased less after surgical therapy, compared to non-surgical therapy. The sites of initial probing depth less than 3 mm lost more clinical attachment level, and the sites of initial probing depth more than 7 mm gained clinical attachment level during maintenance phase after non-surgical therapy, compared to surgical therapy. Non-surgical therapy resulted in greater reduction of tooth mobility than surgical therapy during maintenance phase. These results indicate that the clinical effects of non-surgical or surgical therapy may be different and may change during the maintenance phase.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.6
• /
• pp.782-790
• /
• 2000

The mainly used polymeric material for the denture is PMMA because of its cost and easiness to handle. So it was widely used material among dentists for past decades. But the acrylic-based denture materials have several common weak points such as shrinkage after curing and lack of strength. In order to solve these problems, we adapted one of hybrid system using acrylic polymer and vinyloligosilsesquioxane(POSS). POSS, which is a well known expandable monomer during polymerization process, may eventually suppress volumetric shrinkage. And the hybrid system makes it possible for the polymer to be stable in various severe conditions. Eight different kinds of samples were designed and synthesized. Each samples were characterized with dynamic mechanical analyser(DMA) to confirm their thermodynamic properties, fractured to analyze the cross-sectional morphology of the samples. And elongation, flexural and impact tests were also executed to evaluate the mechanical properties of the samples. From the results, hybrid composites had well defined crosslinked network structure compared to the widely used denture materials, and the mechanical strength improved without changing any surface condition as increment with POSS ratio in hybrid system. Fractured morphology showed homogeneous surfaces in spite of mutli component system, therefore we can conclude that the adoption of the POSS brought the reinforcement of the denture resin.