• Journal of the Korean Wood Science and Technology
• /
• v.26 no.1
• /
• pp.38-50
• /
• 1998

Laser cutting tests were conducted to investigate the laser cutting characteristics of solid woods such as 25mm-thick white oak(Quercus acutissima) and maple(Acer mono), and wood-based panels such as 15mm-thick medium density fiberboard and particleboard. Test variables were laser power, cutting speed, grain direction, and moisture content. Specific cutting energy was measured and the qualities of cut surface were estimated in constant laser power. Specific cutting energy of white oak was larger than that of maple, and specific cutting energy of medium density fiberboard was smaller than that of particleboard. For both white oak and maple, specific cutting energy of green wood was smaller than that of air-dried wood because weight loss of moisture evaporation in green wood was larger than that in air-dried wood. In laser-cut surface, wood cells were not deformed and damaged, but in circular saw-cut surface fibers were pushed out and cut, and wood cells were deformed severely. However, mechanical surface roughness of saw-cut surface was smoother than that of laser-cut surface because of the existence of undeformed cell cavity in laser-cut surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.90-93
• /
• 2004

In this work, we have used different techniques for the surface passivation: conventional thermal oxidation (CTO), rapid thermal oxidation (RTO), and plasma-enhanced chemical vapour deposition (PECVD). The surface passivation qualities of eight different single and combined double layer have been investigated both on the phosphorus non-diffused p-type FZ silicon and on phosphorus diffused emitter of 100 ${\Omega}/Sq$ and 40 ${\Omega}/Sq$. In the single layer, silicon dioxide $(SiO_2)$ passivates good on the emitter while silicon nitride (SiN) passivates better than on the non-diffused surface. In the double layers, CTO/SiN1 passivates very well both on non-diffused surface on the emitter. However, RTO/SiN1 and RTO/SiN2 stacks are more suitable for surface passivation in solar cells caused by a relatively good passivation qualities and the low optical reflection. Applying these stacks in solar cells we achieved 18.5 % and 18.8 % on 0.5 ${\Omega}$ cm FZ-Si with planar and textured front surface, respectively. The excellent open circuit voltage $(V_{oc})$ of 675.6 mV is obtained the planar cell with RTO/SiN stack.

• Journal of the Korean Vacuum Society
• /
• v.7 no.s1
• /
• pp.57-77
• /
• 1998

Heteroepitaxial $Y_2O_3$ films were grown on a Si(111) substrate by ionized cluster beam deposition(ICBD) in ultra high vacuum, and its qualities such as crystllitnity, film stress, and morphological characteristics were investigated using the various measurement methods. The crystallinity was investigated by x-ray diffraction (XRD) and reflection high energy electron diffraction (RHEED). Interface crystallinity was also examined by Rutherford backscattering spectroscopy(RBS) channeling, transmission electron microscopy(TEM). The stress of the films was measured by RBS channeling and XRD. Surface and interface morphological characteristics were investigated by atomic force microscopy (AFM) and x-ray scattering method. Comparing the interface with the surface characteristics, we can conclude that many defects at the interface region were generated by interface reaction between the yttrium metal and SiO2 layer and by ion beam characteristic such as shallow implantation, so that they influenced the film qualities. The film quality was dominantly depended on the characteristic temperature range. In the temperature range from $500^{\circ}C$ to $600^{\circ}C$, the crystallinity was mainly improved and the surface roughness was drastically decreased. On the other hand, in the temperature range from $600^{\circ}C$ to $700^{\circ}C$, the compressive stress and film density were dominantly increased, and the island size was more decreased. Also the surface morphological shape was transformed from elliptical shape to triangular. The film stress existed dominantly at the interface region due to the defects generation.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.40 no.3
• /
• pp.117-121
• /
• 2007

To optimize the mixing ratio of ingredients to obtain the best sensory qualities, a response surface methodology with a central composite design was performed on hot water extracts using crucian carp Carassius carassius treated with diluted vinegar (pH 5.24-5.30). The optimal solutions for four parameters (overall acceptability, odor, flavor, and taste) were obtained using the second-order response surface regression models. The optimal formulation appeared to be 124.15 g of ginger and 96.09 g of garlic with 1 kg of ground crucian carp meat based on the desirability function technique.

• Ocean Science Journal
• /
• v.43 no.1
• /
• pp.9-16
• /
• 2008

Environmental qualities of coastal water and bottom sediment were assessed at Jordan's northernmost tip of Gulf of Aqaba to evaluate possible impacts of the bordering fish pen cages in Eilat. Results showed significant differences between surface and bottom water in the chemical and physical variables in the different months of the year (2004-2005). Chlorophyll a was also significantly higher in bottom water when compared to that of the offshore water. Nitrate and ammonia were significantly higher in bottom water than the surface water at each individual station. The upper 2 cm of sediment sample recorded higher values of total phosphorus and organic matter. Seasonality affected the content of total phosphorus, organic matter, redox potential and color especially at the sediment layer below 3 cm of the sediment core. The present investigation showed slight modification of water and sediment qualities but no clear sign of eutrophication was observed. However, to maintain sustainability of healthy environmental conditions at the northern tip of Gulf of Aqaba potentials of any possible environmental risks arising from the fish farms or any other coastal investment should be carefully considered.

• Journal of Microbiology and Biotechnology
• /
• v.31 no.10
• /
• pp.1366-1372
• /
• 2021

Bacterial nanocellulose (BNC) is a biocompatible material with a lot of potential. To make BNC commercially feasible, improvements in its production and surface qualities must be made. Here, we investigated the in situ fermentation and generation of BNC by addition of different cellulosic substrates such as Avicel and carboxymethylcellulose (CMC) and using Komagataeibacter sp. SFCB22-18. The addition of cellulosic substrates improved BNC production by a maximum of about 5 times and slightly modified its structural properties. The morphological and structural properties of BNC were investigated by using Fourier transform-infrared spectroscopy (FT-IR), scanning electron microscopy and X-ray diffraction. Furthermore, a type-A cellulose-binding protein derived from Clostridium thermocellum, CtCBD3, was used in a novel biological analytic approach to measure the surface crystallinity of the BNC. Because Avicel and CMC may adhere to microfibrils during BNC synthesis or crystallization, cellulose-binding protein could be a useful tool for identifying the crystalline properties of BNC with high sensitivity.

• Ocean and Polar Research
• /
• v.25 no.4
• /
• pp.459-468
• /
• 2003

Annual variation of water qualities in the Shihwa Lake were observed 18 times from June 1996 to October 2001. We studied at the station of the upper streams and near the water gate of lake. After the flow of the outer seawater through the water gate, the surface salinity in Shihwa Lake increased to the range of 25-30 psu in both stations after October 1998. Due to the declination of the salinity differences between the surface and the bottom water, the pycnocline in which had existed until 1997 has weakened, and made the water column mix vertically. This led to the improvement of anoxic/hypoxic environment at bottom waters after April 1998. However, despite the continuous flow of the outer seawater, the concentrations of chlorophyll-a at surface layer were varied from $2{\mu}g/l\;to\;60{\mu}g/l$, and these values indicated the eutrophication. The following organic matter load was greatly influencing the surface layer's COD concentration. During the rainy season, the salinity at the surface layer to the below 15 psu resulting in stratification between the surface and bottom layer. Organic matters that were provided from the surface layer to the bottom layer due to active primary production in the year exhausted dissolved oxygen at the bottom layer, and the bulks of organic matters at bottom gave rise to hypoxic or anoxic environment. It was observed that the enrichment of ammonia and phosphate were main factors to worsen the water quality of the Shihwa Lake. The results of examining the annual variations in Shiwha Lake through principal component analysis shown that water characteristics in the rainy season were similar with those before input of outer sea water.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.3
• /
• pp.72-79
• /
• 2002

Though the laser cutting process is increasingly used in industry, a process automation and systematic database is still yet to be developed. In this study, as the fundamental step toward the construction of a reliable process expert system, a laser cutting quality monitoring/analysis system is developed based on simulations and experimental results. The relations between laser process parameters and laser cutting surface quality parameters such as kerf geometry, striation, surface roughness and dross formation are characterized and analyzed. A graphical user interface is used to visualize the results.

• Asian-Australasian Journal of Animal Sciences
• /
• v.12 no.2
• /
• pp.220-225
• /
• 1999

The environmental conditions in smallholder dairy farms especially the effects of dairy wastes on waters and soil were the main objectives of this investigation. Forty-three dairy farms from an older dairy cooperative (Nongpho Dairy Cooperative, NP) were compared with four dairy fauns from relatively new dairy cooperative (Kamphaengsaen Dairy Cooperative, KS) for the quality parameters of water and soil samples during a 12-month period. Forty-three farms at NP were from three geographical areas and three levels farm crowdedness. The results from this study clearly showed that the waste waters from older dairy barns contained much higher levels of organic and inorganic substances which could create environmental pollution if not properly managed. The differences in waste water qualities due to areas and seasons were not significant, while waste water samples from crowded farms tended to contain higher averages of waste water parameters such as COD and BOD. Highly significant correlations between pairs of waste water parameters indicated that certain parameters can be used without the need for chemical analysis of some other parameters. The qualities of well water on dairy farms as well as water samples from public waterways nearby indicated some contamination of dairy wastes such as manure. Storage and sun-drying of dairy manure on bare soil surface could result in the contamination of underground water and nearby water sources. Some recommendations from this study if implemented can prevent environmental pollution in smallholder dairy farms.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.4
• /
• pp.31-36
• /
• 2009

In this paper, the laser cutting characteristics of the flexible PCB using high power Nd:YAG UV laser were investigated. A specific FPCB model was selected for the experiment. Test sheets were made, which had equal materials and layer structure to those of the outline (OL) region and the contact pad (CP) region in the FPCB. The experiment is made up of two stages. In the first stage of the experiment, the laser cutting fluence was found, which is the threshold fluence to cut the test sheets completely. The laser cutting fluence of the OL sheet is $1781.26{\sim}1970.16\;J/cm^2$ and that of the CP sheet is $2109.34{\sim}2134.34\;J/cm^2$. In the second stage, cutting performance and its qualities were analyzed by the experiment. The laser cutting performance remained almost unchanged for all laser and process parameter sets. The average cutting width (top side/bottom side) of the OL sheet was $40.45\;{\mu}m/11.52\;{\mu}m$ and that of the CP sheet was $22.14\;{\mu}m/10.93\;{\mu}m$. However, the laser cutting qualities were different according to the parameters. The adjacent region of the cutting line on the OL sheet was carbonized as the beam speed was low and the overlap coefficient was high. The surface quality around the cutting line of the CP sheet was about the same. Carbonization and debris occurred on the surface of the cutting line. As a result of the experiment, the cutting qualities were better as the overlap coefficient was made low and beam speed high. Therefore, the overlap coefficient 2 or 3 is proper for the FPCB laser cutting.