• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.53.2-53.2
• /
• 2010

In this study, we focused on our specialized electrode process for Si back-contact crystalline solar cell. It is different from other well-known back-contact cell process for thermal aspect and specialized process. In general, aluminum makes ohmic contact to the Si wafer and acts as a back surface reflector. And, silver is used for low series resistance metal grid lines. Aluminum was sputtered onto back side of wafer. Next, silver is directly patterned on the wafer by screen printing. The sputtered aluminum was removed by wet etching process after rear silver electrode was formed. In this process, the silver paste must have good printability, electrical property and adhesion strength, before and after the aluminum etching process. Silver paste also needs low temperature firing characteristics to reduce the thermal budget. So it was seriously collected by the products of several company of regarding low temperature firing (below $250^{\circ}C$) and aluminum etching endurance. First of all, silver pastes for etching selectivity were selected to evaluate as low temperature firing condition, electrical properties and adhesive strength. Using the nano- and micron-sized silver paste, so called hybrid type, made low temperature firing. So we could minimize the thermal budget in metallization process. Also the adhesion property greatly depended on the composition of paste, especially added resin and inorganic additives. In this paper, we will show that the metallization process of back-contact solar cell was realized as optimized nano-paste characteristics.

• Nuclear Engineering and Technology
• /
• v.47 no.5
• /
• pp.523-533
• /
• 2015

Three-dimensional flow phenomena in a wire-wrapped 37-pin fuel assembly mock-up of a Japanese loop-type sodium-cooled fast reactor, Monju, were investigated with a numerical analysis using a general-purpose commercial computational fluid dynamics code, CFX. Complicated and vortical flow phenomena in the wire-wrapped 37-pin fuel assembly were captured by a Reynolds-averaged Navier-Stokes flow simulation using a shear stress transport turbulence model. The main purpose of the current study is to understand the three-dimensional complex flow phenomena in a wire-wrapped fuel assembly to support the license issue for the core design. Computational fluid dynamics results show good agreement with friction factor correlation models. The secondary flow in the corner and edge subchannels is much stronger than that in an interior subchannel. The axial velocity averaged in the corner and edge subchannels is higher than that averaged in the interior subchannels. Three-dimensional multiscale vortex structures start to be formed by an interaction between secondary flows around each wire-wrapped pin. Behavior of the large-scale vortex structures in the corner and edge subchannels is closely related to the relative position between the hexagonal duct wall and the helically wrapped wire spacer. The small-scale vortex is axially developed in the interior subchannels. Furthermore, a driving force on each wire spacer surface is closely related to the relative position between the hexagonal duct wall and the wire spacer.

• Journal of the Korean Geographical Society
• /
• v.41 no.4 s.115
• /
• pp.418-434
• /
• 2006

The study was investigated to runoff characteristics of non-point pollutants according to rainfall in Kokseong river watershed. The result of which is as follows : First of all, major reason which affect the formation of water quality of Kokseong River is judged to be caused by non-point pollution source which flows out from farmland and residential area. Flow of rainfall effluent in the downstream in which direct flow components of urban district and combined sewer overflows of farmland was intervened faster than that in the upstream reacted more promptly. Generation of pollutants by non-point source shows increasing trend in general in accordance with the increase in the intensity of rainfall but it was affected by SS, BOD, COD and T-P in the upstream part whereas BOD, COD and T-N were significantly affected by beginning period of rainfall in the downstream. EMC in the downstream increased approximately 3-315 times as compared to upstream, particularly the discharge of SS5 and T-P were extremely increased. While surface flow out of rainfall effluent in the upstream was only 4.7%, the surface flow in the downstream took up as much as 29%, which was major reason for the increase of EMC. From the above contents, we can see that the change in water quality according to the increase and decrease of effluent at the time of rainfall showed very complex pattern depending on the type of land use, and it is judged that the most important thing for the administration of non-point pollution source is to come up with the solution for the reduction of effluent at the beginning.

• Korean Journal of Remote Sensing
• /
• v.12 no.2
• /
• pp.126-138
• /
• 1996

The characteristics of rapid development of the low pressure system over the East Sea from 06 to 08 Nov., 1995 has been analyzed in detail by the synoptic numerical products and satellite observations. The Low system was initially triggered the development of the baroclinic leaf cloud over the border of the northern part of Korea and China and moved eastward and then developed explosively com-ma or lambda type cloud system over the East Sea. To forecast well the general development and movement of the coastal winter cyclone over the East Sea popularly in a numerical simulation by several scientists, the large baroclinicity, continuous support of water vapor, and sequential cold outbreak over the warm sea surface have been more commonly concerned about. The cyclone which the central surface pressure was dropped 40hPa within 24 hours has often accompanied strong wind and heavy snow- or rain-fall in the winter season. In all successive observations with 12-hourly satellite imagery and analyzed meteorological variables in this period, the centers of the sea-level pressure and 500hPa geopotential height associated with this cyclone were typically illustrated by moving farther eastward using GMS combined enhanced IR images. The maxi-mum wind sustained by this system with the intensity and central pressure of tropical storm was about 60 knots with the center pressure drop of 44hPa/day similar to the North American cyclonic bomb and Atlantic storm.

• The Journal of Korean Academy of Prosthodontics
• /
• v.18 no.1
• /
• pp.7-13
• /
• 1980

The purpose of this study was to evaluate the removable partial denture prescriptions including surveyed crowns and design of component parts sent to the laboratory technician. A total of 351 casess with prescription forms and master cast in maxillary and mandibular semi-edentulous situations collected from dental laboratory by random sampling were selected for this study. The evaluation and study observed here involved the classification of edentulous situations, status of abutment splinting, form of rest seats and guiding plane of surveyed crows, location of maxillary major connectors and tripodig marks on the master casts. Removable partial denture prescriptions contained (1) general request (upper and lower cast framework), (2) types of metal, (3) location of retainer(retention, lingual bracing, rest area, guiding plane surface), (4) location and type of major connector, (5) relief area and amount, (6) and other specific instructions. The following informations based on the classified groups such as Group I was those cases sent with no real prescriptions. They say 'make a partial.' No prescriptions, no thought beforehand, Group II was those cases sent with a minimal prescriptions. They say 'make a partial with clasps on May be some preparations, usually inadequate. Group III was those cases sent with a moderately good prescription. Adequate but could be much better. No tripoding but it tell what clasps go where. Still not good prescriptions. Group IV was good cases, tripoded with adequate prescriptions and a prescription which exactly describes what is expected from the laboratory. The analyzed results were as follows: 1. The normal form of rest seats and guiding plane of surveyed crowns in Class. I and Class. II edentulous situations on the maxillary cast were observed 31.9% and 27.89%, respectively. The abutment teeth and retainer without occlusal rests of Class. I and Class. II were showed 11.58% and 8.86%, respectively. In mandibular cases, the normal form of rest seats and guiding plane of surveyed crowns showed 27.54% and 8.82% in Class. I and Class. II situation. The abutment teeth and retainer without rest seats were showed 15.19%, respectively. 2. The splinted surveyed crowns of Class. I and Class. II maxillary edentulous situations in distal extension cases were showed 34.51% and 28.85%, but 28.52% and 10.29%, respectively. 3. The location and type of maxillary major connector delineated on the master cast were 66 cases (44.89%). 4. The results of 351 cases were classified as Group I 146(41.59%), Group II 115 (32.76%), Group III 57 (16.23%), and Group IV 33 (9.48%). 5. The delineation of abutment tooth for clasping were 176 cases (50.14%) among total of 351 cases. 6. The delineation of height of contour line were showed 45 cases (12.8%) in Group II, 14 cases (3.98%) in Group III and 33 cases (9.40%) in Group IV with total 92 cases (26.21%). 7. In surveying procedure, the delineation of tripoding marks and reference line were showed 17 cases (4.84%).

• Fire Science and Engineering
• /
• v.28 no.5
• /
• pp.8-13
• /
• 2014

The purpose of this study is to analyze the damage pattern when overcurrent is applied to a thermal magnetic type molded case circuit breaker (MCCB) using a Primary Current Injection Test System (PCITS). When an overcurrent of 150 A was applied to the PCITS for 5 seconds with the trip bar of an MCCB being damaged, it was found that the surface of the temperature control device (bimetallic strip) positioned at the right was significantly carbonized. When an overcurrent of 300 A was applied to the PCITS for 5 s under the same conditions, the entire temperature control device was deteriorated, becoming flattened and in close contact with the MCCB. When an overcurrent of 450 A was applied to the PCITS for 5 s, the coil of the temperature control device was melted and disconnected. In addition, it was observed that the contacts, the enclosure and upper cover were deformed and there was a trace of carbonization on them. When approximately 3 s had elapsed after an overcurrent of 600 A was applied, white smoke occurred inside the MCCB and a flame was radiated out, after which the overcurrent supply stopped with "phutt" (whomp) sound. It was observed that when the same type of MCCB is damaged by a general flame, the surfaces of its handle, terminal, arc divider (extinguisher) and temperature control device were carbonized uniformly. In addition, it was found that the trip bar of the operating mechanism was melted down and the metal operation pin was moved while being tripped.

• Cross-Cultural Studies
• /
• v.50
• /
• pp.425-451
• /
• 2018

In this paper, we examined the issues of the discussions on the subject of doublets. In general, as a definition, the use of doublets refer to a pair of words which have a common etymon, but also to a pair of words or grammatical morphemes that have the same meaning and similar forms of the word. In this paper, we have seen that a typical pairing word is a pair of words with a common etymology. Generally speaking, it is possible to divide doublets into subtypes depending on the identified similarities or differences in the meaning or form. The most distant type from the typical type of doublets is a pair of words that do not have a common etymon, but have the same meaning and are similar in form. The second issue about doublets is whether doublets include only words. For example, if some josas (postpositions or particles) have a common etymon, then it is noted that they can be accepted as a kind of doublets. In the case of suffixes, it may be possible to recognize the suffixes as doublets if they have a common etymon. In other words, it is not necessary to recognize the suffixes as doublets because the derivatives which are derived by the suffixes can be accepted as doublets. In the case of endings, it may be possible to recognize a pair of endings which have the same meaning and the common etymon as a doublet. Otherwise, the word forms to which the endings are combined can be accepted likewise as doublets. However, considering the fact that the endings typically in use in the Korean language may have syntactic properties, the endings should be considered as doublets rather than the words which have the endings. Finally, we conclude that there may be some debate as to whether stem doublets or ending doublets belong to a lexical item in the lexicon. It can be said that they are plural underlying forms and may be deserving of further research.

• Journal of the Korean Chemical Society
• /
• v.43 no.1
• /
• pp.28-42
• /
• 1999

Polysilanes with sterically bulky substituents, -[2-( $R^1R^2$-phenyl)propyl]Si[$R^3$]-, such as poly(2-phenylpropyl)(n-hexyl)silane [$R^1=R^2$=H, $R^3$=n-hexyl] were prepared by Wurtz-type coupling reactions with Na using a sonochemical method. The high-intensity ultrasound provided the formation of high quality Na dispersion in toluene and its active surface which was important for the synthesis of polysilanes in Wurtz-type coupling reaction was freshly and continuously regenerated during the process. The polysilanes products were mixtures of high molecular weight polymers with $\={M}_W$ of ∼$10^6$ and low molecular weight polymers with $\={M}_W$ of ∼$10^3$. It was found that the formation of high molecular weight polymerr was greatly influenced by the substituents $R^3$, directly attached to Si. On the contrary, changes on substituents ($R^1, R^2$) gave no influences at all. Overall yields for polysilanes were 75-99% in general but high molecular weight polysilanes were obtained as a major product when substituent $R^3$ is n-hexyl group and low molecular weight polysilanes were obtained as a major product when substituent $R^3$ is cyclohexyl and 2-phenylethyl groups. Effects of reaction conditions to polysilane yields were investigated.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.4
• /
• pp.341-348
• /
• 2010

The basic principle of fry drying process of sludge lies in the rapid pressure change of sludge material caused by the change of temperature between oil and moisture due to the difference of specific heat. Therefore, the rapid increase of pressure in drying sludge induces the efficient moisture escape through sludge pores toward heating oil media. The object of this study is to carry out a systematic investigation of the influence of various parameters associated with the sludge fry drying processes on the drying efficiency. To this end, a series of parametric experimental investigation has been made together with the numerical calculation in order to obtain typical drying curves as function of important parameters such as drying temperature, sludge diameter, oil type and sludge type. In the aspect of frying temperature, especially it is found that the operation higher than $140^{\circ}C$ was favorable in drying efficiency regardless of type of waste oil employed in this study. The same result was also noted consistently in the investigation of numerical calculation, that is, in that the sludge particle drying was efficiently made over $140^{\circ}C$ irrespective of the change of particle diameter. As expected, in general, the decrease of diameter in sludge was found efficient both experiment and numerical calculation in drying due to the increased surface area per unit volume. In the investigation of oil type and property, the effect of the viscosity of waste oil was found to be more influential in drying performance. In particular, when the oil with high viscosity, a visible time delay was noticed in moisture evaporation especially in the early stage of drying. However, the effect of high viscosity decreased significantly over the temperature of $140^{\circ}C$. There was no visible difference observed in the study of sludge type but the sewage sludge with a slightly better efficiency. The numerical study is considered to be a quite useful tool to assist in experiment with more detailed empirical modeling as further work.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.4
• /
• pp.138-164
• /
• 2022

The Neolithic shell midden in Daejuk-ri, Seosan, is distributed on the gentle slope of a low hill close to the west coast. The bedrock of the area consists mainly of schist with various mafic minerals, but shows a partial gneiss pattern. The site consists of loamy topsoil and clay loam subsoil, and the degree of siallization is relatively low. Although the pottery excavated from the shell midden shares mostly similar features, a variety of shapes and patterns coexist. The surface colors, thickness and physical properties are slightly different. The pottery can be subdivided into three types (IA, IB and II) according to the composition of the body clay, the temper and the existence of a black core. Types IA and IB are colorless mineral pottery with a non-black or black core respectively. TypeII is colored mineral pottery with a non-black core. Type I pottery also contains non-plastic colored minerals, but type II contains a large amount of biotite, chlorite, talc, amphibole, diopside and tremolite, which include a large amount of Mg and Fe. The studied pottery contains a small amount of organic matter. Considering the grain size and relatively poor sorting and roundness of the non-plastic particles, the pottery appears to be made by adding coarse non-plastic tempers for special purposes to the untreated weathered soil around the site. The three types of pottery seem to have been incompletely fired in general. While type IB has the lowest degree of oxidation, typeII shows the highest degree of redness and oxidation. It can be interpreted that these differences depend on the firing temperature and the ratio of non-plastic particles. Through a synthesis of the minerals, geochemical data and thermal history, it can be determined that the firing temperature ranged from 600 to 700℃. The pottery types of the Daejuk-ri Shell Midden have slightly different production conditions, mineral compositions, and physical properties, but have undergone similar production processes with basically the same clay materials. The clay is almost identical to the composition of the bedrock and weathered soil distributed in the Daejuk-ri area. Currently, there is an industrial complex in the area, so it is difficult to confirm the soil and geological distribution of the site. However, it is highly probable that the area around the site was self-sufficient for the clay and tempers required for the production of the Neolithic pottery. Therefore, it can be interpreted that the group that left the shell midden in Daejuk-ri lived near the site, visited the site for the purpose of collecting and processing shellfish, and discarded the broken pottery along with shells.