• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.133-140
• /
• 2017

This study investigates the oxidation properties of Fe-14Cr ferritic oxide-dispersion-strengthened (ODS) steel at various high temperatures (900, 1000, and $1100^{\circ}C$ for 24 h). The initial microstructure shows that no clear structural change occurs even under high-temperature heat treatment, and the average measured grain size is 0.4 and $1.1{\mu}m$ for the as-fabricated and heat-treated specimens, respectively. Y-Ti-O nanoclusters 10-50 nm in size are observed. High-temperature oxidation results show that the weight increases by 0.27 and $0.29mg/cm^2$ for the as-fabricated and heat-treated ($900^{\circ}C$) specimens, and by 0.47 and $0.50mg/cm^2$ for the as-fabricated and heat-treated ($1000^{\circ}C$) specimens, respectively. Further, after 24 h oxidation tests, the weight increases by 56.50 and $100.60mg/cm^2$ for the as-fabricated and heat-treated ($1100^{\circ}C$) specimens, respectively; the latter increase is approximately 100 times higher than that at $1000^{\circ}C$. Observation of the surface after the oxidation test shows that $Cr_2O_3$ is the main oxide on a specimen tested at $1000^{\circ}C$, whereas $Fe_2O_3$ and $Fe_3O_4$ phases also form on a specimen tested at $1100^{\circ}C$, where the weight increases rapidly. The high-temperature oxidation behavior of Fe-14Cr ODS steel is confirmed to be dominated by changes in the $Cr_2O_3$ layer and generation of Fe-based oxides through evaporation.

• Journal of Conservation Science
• /
• v.33 no.5
• /
• pp.355-362
• /
• 2017

The Nongso tomb of Sunchang was built in a relatively deep place; hence there was little damage from grave robbers. The tomb was completely filled with a large amount of charcoal, and therefore the wooden coffin was excavated in relatively good condition. On the basis of the structure of the tombs, excavated artifacts, and radiocarbon dating results, the tomb is estimated to be from between the late Goryeo and the early Joseon period. The wooden coffin excavated is double-layered structures consisting of an outer coffin and an inner coffin. The outside of the wooden coffin is thickly lacquered and decorated with yellow letters and white motifs. An analysis of the pigments' components revealed that the major component of the letters was gold (Au) and the major component of the motifs was silver (Ag). The coffin lacquer had three layers: a pigment layer, a yellowish-brown layer, and a black layer. The wooden bases of the coffins were painted with a black substance, such as soot, as mineral elements were not detected in the black layer. The yellowish-brown layer is presumed to be refined lacquer. From the analysis of the structure of the layers and pigments, we can estimate the method was adopted for making lacquer for wooden coffin. It is assumed that the method used gold leaf and gold powder. The form of the pigment and the internal structure are likely to be gold leaf, but the shape of the surface letters appears to have been formed using gold powder. This study will serve as important information for understanding lacquer making techniques at the time of the tombs' construction by confirming the making method through reproduction experiments using gold leaf and gold powder.

• Journal of Conservation Science
• /
• v.36 no.5
• /
• pp.405-420
• /
• 2020

A convergence research was conducted on glass beads excavated at the ruins of Hapgang-ri, Sejong, using the archeology and conservation approach. The period of appearance of Jugu Towangmyo in the ruins of Hapgang-ri can be estimated to begin in the late 2^nd century; for Jugu Towangmyo No. 15, the period spans from the late 2^nd to early 3^rd century. Form, color, and manufacturing techniques of complete glass beads were examined, and the cross-sections and chemical composition of 16 samples were observed. Based on these analyses, the glass beads were divided into blue, purple, and red colors. The blue-colored beads could be further sub-divided based on their gloss and brightness; in contrast, the red-colored beads were highly uniform with regard to these parameters. Based on the stripe and bubble arrangement on the surface of the glass beads, their drawing technique was identified. Traces of heat treatment or polishing were observed at the ends of the beads. According to their chemical composition, the 16 samples were classified into 3 potash glass and 13 soda glass groups; in the latter, the properties of the stabilizers were divided according to the blue and red bead colors. The stabilizers of the red beads are unique in that they allow the distinction among beads excavated in other areas in South Korea owing to their compositional differences. Colorants in blue- and red-colored beads are cobalt (containing MnO), and copper and iron, respectively.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.16 no.3 s.43
• /
• pp.197-207
• /
• 1992

Expressionism, is as diverse as the artists invo)ved, in a very broad sense two main tendencies may be noted. The first is that of the Action painters, concerned in different ways with the gesture of the brush and the texture of the paint. It included such major artists as Arshile Gorky, Jackson Pollock, Willem De Keening, and Franz Kline. The other group consisted of the Color Field painters, concerned with the statement of an abstract sign or tranquil image in terms of a large, unified color shape or area. Here must be included Mark Rothko, Barnett Newman, Ad Rdinhardt, as well as, to a degree, Adolph Gottlieb, Robert Motherwell, and Clyf(ord Still. In this paper, 1 selected two artists Arshile Gorky and Jackson Pollock independent charac-teristics and studied the influence of their Action painting on the fabrics of modern fashion. However, it should be noted it was never the intention of the critic Harold Rosenberg, in coining this term, to imply that Action painting was a kind of athletic exercise. Nor is it true that the furious and seemingly haphazard scattering of the paint involved a completely uncontrolled, intuitive act. There is no question that, in the paintings of Jackson Pollock, Arshile Gorky and many of the other Abstract Expressionists, the element of intuition or the accidental plays a large and deliberate part; this was indeed one of the principal contributions of Abstract Expressionism which had found its own inspiration in surrealism's 'psychic automaton'. However, nothing that an experienced and accomplished artist does can be completely accidental. Aside from their intrinsic quality, the spun-out skeins of poured pigments contributed other elements that changed the course of modern painting. There was the concept of the all-over painting, the painting seemingly without beginning or end, extending to the very limits of the canvas and implying an extension even beyond. The feeling of absorption or participation is heightened by the ambiguity of the picture space. The colors and lines, although never punctur-ing deep perspective holes in the surface, still create an illusion of continuous movement, a billowing, a surging back and forth, within a limited depth. To study the influence of Abstract Expressionism on the fabric of modern fashion, 1 selected and examined four fashion magazines: Collezioni published in France, Bazaar in Italy, Gap in Japan and Vogue in the U.S.a. froim January 1989 to June 1991. As a result of this review I found that some fabrics used in modern clothing are printed in a dripping, pouring and splashing style without any meaning or form. Slides included in the presentation show that modern fabrics which are printed in such a style were influenced by Abstract Expressionism. The slides also show that these abstract prints are well suited to modern fashion design.

• Korean Journal of Environmental Agriculture
• /
• v.5 no.1
• /
• pp.30-34
• /
• 1986

This study was carried out to determine the heavy metal contents in sluges of Keumho river and her branches. The heavy metal contents of sludge are the highest in Sincheon, Kongdancheon and Dalseocheon among the branches. The large part of heavy metal exists in $0{\sim}5cm$ from sludge surface. The sequential extraction with various reagents showed that the residual and organically bound fraction were the most abundant pool. Decomposition of organic matter caused sludge to release heavy metals. On the extraction of sludge with various solution having different pH, it was found that the lower the pH, the more heavy metal was extracted. However, considerable amount of heavy metal was not extracted even with pH 3 solution.

• The Journal of Engineering Geology
• /
• v.25 no.3
• /
• pp.377-385
• /
• 2015

We constructed a model test apparatus to evaluate the dependence of the saturation velocity (V_s) in soils on rainfall intensity (I_R). The apparatus comprises a soil box, a rainfall simulator, and measuring sensors. The model grounds (60 cm × 50 cm × 15 cm) were formed by Joomunjin standard sand with a relative density of 75%. The rainfall simulator can control the rainfall intensity to reenact the actual rainfall in a soil box. Time Domain Reflectometer (TDR) sensors and tensiometers were installed in the soils to measure changes in the volumetric water content and matric suction due to rainfall infiltration. During the tests, the soil saturation was determined by raising the groundwater table, which was formed at the bottom of the soil box. [Please check that the correct meaning has been maintained.] The wetting front did not form at the ground surface during rainfall because the soil particles were uniform and the coefficient of permeability was relatively high. Our results show that the suction stress of the soils decreased with increasing volumetric water content, and this effect was most pronounced for volumetric water contents of 20%-30%. Based on a regression analysis of the relationship between rainfall intensity and the average saturation velocity, we suggest the following equation for estimating the saturation velocity in soils: V_savg (cm/sec) = 0.068I_R (mm/hr).

• Applied Microscopy
• /
• v.39 no.1
• /
• pp.65-72
• /
• 2009

Cryo-SEM which enables specimens to be observed in frozen form has been used to study liquid specimens in their native states. Cryo-methods, sample preparation for cryo-SEM, are quite complex and involve several discrete but vitally interconnected steps which are rapid cooling, fracturing, sectioning, etching and coating. It is important to select practical techniques and to optimize conditions of each steps considering analytic purpose and specimen characters, viz., sample dimension, water contents. In this study, etching methods and sample preparation before freezing had been studied for observation of cyanobacteria, Synechocystis sp. PCC 6803 using cryo-SEM and their cryo-SEM images were compared to Conventional SEM (CSEM) images treated by chemical fixation. We could observe the improved morphological images of the pili of the surface and membranes of Synechocystis sp. PCC 6803 and the three-dimensional architectures of their biofilm, which were difficult to observe using chemical fixation and CSEM. These results suggest that cryo-methods/cryo-SEM are useful techniques for morphological study of biological specimen.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.554-558
• /
• 2008

$(1-x)SiO_2-(x)TiO_2$ composite fibers with various compositions of $TiO_2$ were prepared by electrospinning their sol-gel precursors of titanium (IV) iso-propoxide (TiP), and tetraethyl orthosilicate (TEOS). The surface morphology and structure of sintered composite fibers were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), simultaneous thermogravimetric analysis-differential scanning calorimetry (TGA-DSC) and Fourier transform infrared spectroscopy (FT-IR). As the content of $TiO_2$ in $(1-x)SiO_2-(x)TiO_2$ system was increased the average diameter of composite fibers was proportionally increased. Also, the transformation of $TiO_2$ from anatase to rutile form was inhibited by the highly dispersed $TiO_2$ around $SiO_2$ particles up to $0.6SiO_2-0.4TiO_2$ composite fibers even after calcination at $1000^{\circ}C$. The photocatalytic activity of $SiO_2-TiO_2$ composite fibers was examined for the methylene blue (MB) decomposition which was confirmed using UV-vis/DRS spectra. The experiments demonstrated that the MB in aqueous solution was successfully photodegraded using $SiO_2-TiO_2$ composite nanofibers under UV-visible light irradiation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2391-2400
• /
• 2015

Weather proof steels are used for steel bridges due to its high corrosion resistance under atmospheric conditions. However, instead of forming stabilized rust layers, general rust occurs on weather proof steels under high humidity condition close to seawater or shady places. In Japan, therefore, they perform rust stabilization treatment instead of unpainted treatment due to severe atmospheric conditions. However, most of domestic weather proof steels were constructed unpainted in the form of closed box-girder, which makes the periodical repetition of dry and wet hard to occur. For the steel bridges constructed on the Han river, the evaporation of water, dew condensation due to temperature change, and stagnant water due to rain affect harmfully on the formation of passive film on weather proof steels. Thus, in this research, in order to analyze corrosion properties inside the closed box-girder for the unpainted weather proof steel bridge in the waterworks safety zone, multiple ways of analysis such as observation with eyes, cellophane-tape test, steel thickness measurement, surface corrosion potential measurement, electron microscope analysis, and X-ray diffraction analysis of the rust were performed. As a result, unstable rust layer was observed inside the closed box-girder, and severe corrosion was observed on the top and bottom of the flanges due to the effects of stagnant water caused by rain, dew condensation, and de-icing materials.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.5
• /
• pp.112-120
• /
• 2012

A numerical model considering the internal vaporization and the creep effect, in the form of a analytical program, for tracing the behavior of high strength concrete(HSC) members exposed to fire is presented. The two stages, i.e., spalling procedure and fire resistance time, associated with the thermal, moisture flow, creep and structural analysis, for the prediction of fire resistance behavior are explained. The use of the analytical program for tracing the response of HSC member from the initial pre-loading stage to collapse, due to fire, is demonstrated. Moisture evaporates, when concrete is exposed to fire, not only at concrete surface but also at inside the concrete to adjust the equilibrium and transfer properties of moisture. Finite element method is employed to facilitate the moisture diffusion analysis for any position of member, so that the prediction method of the moisture distribution inside the concrete members at fire is developed. The validity of the numerical model used in this program is established by comparing the predictions from this program with results from others fire resistance tests. The analytical program can be used to predict the fire resistance of HSC members for any value of the significant parameters, such as load, sectional dimensions, member length, and concrete strength.