• Geomechanics and Engineering
• /
• v.37 no.6
• /
• pp.599-614
• /
• 2024

To evaluate the safety status of deteriorated segments in a submarine shield tunnel during its service life, a seepage model was established based on a cross-sea shield tunnel project. This model was used to study the migration patterns of erosive ions within the shield segments. Based on these laws, the degree of deterioration of the segments was determined. Using the derived analytical solution, the internal forces within the segments were calculated. Lastly, by applying the formula for calculating safety factors, the variation trends in the safety factors of segments with different degrees of deterioration were obtained. The findings demonstrate that corrosive seawater presents the evolution characteristics of continuous seepage from the outside to the inside of the tunnel. The nearby seepage field shows locally concentrated characteristics when there is leakage at the joint, which causes the seepage field's depth and scope to significantly increase. The chlorine ion content decreases gradually with the increase of the distance from the outer surface of the tunnel. The penetration of erosion ions in the segment is facilitated by the presence of water pressure. The ion content of the entire ring segment lining structure is related in the following order: vault < haunch < springing. The difference in the segment's rate of increase in chlorine ion content decreases as service time increases. Based on the analytical solution calculation, the segment's safety factor drops more when the joint leaks than when its intact, and the change rate between the two states exhibits a general downward trend. The safety factor shows a similar change rule at different water depths and continuously decreases at the same segment position as the water depth increases. The three phases of "sudden drop-rise-stability" are represented by a "spoon-shaped" change rule on the safety factor's change curve. The issue of the poor applicability of indicators in earlier studies is resolved by the analytical solution, which only requires determining the loss degree of the segment lining's effective bearing thickness to calculate the safety factor of any cross-section of the shield tunnel. The analytical solution's computation results, however, have some safety margins and are cautious. The process of establishing the evaluation model indicates that the secondary lining made of molded concrete can also have its safety status assessed using the analytical solution. It is very important for the safe operation of the tunnel and the safety of people's property and has a wide range of applications.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1991.10a
• /
• pp.87-102
• /
• 1991

It has been reported that the failure of Carsington Dam in Eng1and occured due to the existence of a thin yellow clay layer which was not identified during the design work, and due to pre-existing shears of the clay layer. The slope stability analyses during the design work, which utilized traditional circular arc type failure method and neglected the existence of the clay layer, showed a safety factor of 1.4. However, the post-failure analyses which utilized translational failure mode considering the clay layer and the pre-existing shear deformation revealed the reduction of safety factor to unity. The post-failure analysis assumed 10。 inclination of the horizontal forces onto each slice based on the results of finite element analyses. In this paper, Bishop's simplified method, Janbu method, and Morgenstern-Price method were used for the comparison of both circular and translational failure analysis methods. The effects of the pre-existing shears and subsquent movement were also considered by varying the soil strength parameters and the pore pressure ratio according to the given soi1 parameters. The results showed factor of safefy 1.387 by Bishop's simplified method(STABL) which assumed circular arc failure surface and disregarding yellow clay layer and pre-failure material properties. Also the results showed factor of safety 1.093 by Janbu method(STABL) and 0.969 by Morgenstern-Price method(MALE) which assumed wedge failure surface and considerd yellow clay layer using post failure material properties. In addition, dam behavior was simulated by Cam-Clay model FEM program. The effects of pore pressure changes with loading and consolidation, and strength reduction near or at failure were also considered based on properly assumed stress-strain relationship and pore pressure characteristics. The results showed that the failure was initiated at the yellow clay layer and propagated through other zones by showing that stress and displacement were concentrated at the yel1ow clay layer.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.5
• /
• pp.583-594
• /
• 2000

Dislodgement of a crown or extension bridge and the loosening of a retainer of a bridge is a serious clinical problem in fixed restoration. Generally these problems are considered to be associated with deformation of the restoration. During biting, the restoration is subjected to complex forces and deforms considerably within the limit of its elasticity. Deformation of the restoration under the occlusal force induces excessive stress in the cement film, which then leads to the cement fracture. Such a fracture may eventually cause loss of the restoration. Because most of the past retention tests for full veneer crown were done without fatigue loading, they were not exactly simulating intraoral environment. And the purpose of this study was to evaluate the effect of cyclic cantilever loading on the retentive strength of full veneer crowns depending on different type of cements and taper of prepared abutment. Steel dies with $8^{\circ}\;or\;16^{\circ}$ convergence angle were fabricated through milling and crowns with the same method. These dies and crowns were divided into 8 groups. Group 1 : $16^{\circ}$ taper die, cementation with zinc phosphate cement, without loading Group 2 : $16^{\circ}$ taper die, cementation with zinc phosphate cement, with loading Group 3 : $8^{\circ}$ taper die, cementation with zinc phosphate cement, without loading Group 4 : $8^{\circ}$ taper die, cementation with zinc phosphate cement, with loading Group 5 : $16^{\circ}$ taper die, cementation with Panavia 21, without loading Group 6 : $16^{\circ}$ taper die, cementation with Panavia 21, with loading Group 7 : $8^{\circ}$ taper die, cementation with Panavia 21 without loading Group 8 : $8^{\circ}$ taper die, cementation with Panavia 21, with loading After checking the fit of die and crown, the luting surface of dies and inner surface of crowns were air-abraded for 10 seconds. The crowns were cemented to the dies, with cements mixed according to the manufacturer's recommendations. A static load of 5kg was then applied for 10 minutes with static loading device. Twenty-four hours later, group 1, 3, 5, 7 were only thermocycled, group 2, 4, 6, 8 were subjected to cyclic loading after thermocycling. Retentive tests were performed on the Instron machine. From the finding of this study, the following conclusions were obtained 1. Panavia 21 showed significantly higher retentive strength than zinc phosphate cement for all groups (p<0.05). 2. There was a significant difference in the retentive strength between $8^{\circ}\;and\;16^{\circ}$ taper for zinc phosphate cement(p<0.05), but no significant difference for Panavia 21 (p>0.05). 3. Cyclic loading significantly decreased the retentive strength for all groups(p<0.05). 4. For zinc phosphate cement, there was 35% reduction of the retentive strength after loading in the $16^{\circ}$ taper die, 25% in the $8^{\circ}$ taper die, and for Panavia 21, 21% in the $16^{\circ}$ taper die, 18% in the $8^{\circ}$ taper die.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.2
• /
• pp.300-307
• /
• 1997

The effects of Aster scaber and Ixeris dentata on cadiovascular system in hyperlipidemic rats were examined. Five groups of thirty Sprague Dawley rats were fed with the diet contained 1% cholesterol, 0.25% sodium cholate, 10% coconut oil and 5% lard(control group) for 4 weeks. Each experimental diet group was added with 5% plant powder or extract of the 5% plant powder by dry weight. Contractile or relaxation responses in the isolated artria and thoracic aortae were measured and the morphological changes of the aortic endotherium from the rats fed the experimental diet were inspected. In response to isoproterenol, the number of right atrial spontaneous beat was significantly lower in Cham chyi powder group$(PP_{1})$ and Sumbagui powder group$(PP_{2})$ than control at $10^(-8)M$ concentration. The contraction forces by injection of phenylephrine and calcium in isolated thoracic aorta were significantly low in each experimental groups compared with the control. The relaxation rates by acetylcholine represented comparatively higher value in $PP_{1}$ than control. The morphological changes of endothelial cell surface was a little in $PP_{1}$ and $PP_{2}$ compared with control, while the damages were considerably advanced in Cham chyi and Sumgbagui extract diet group$(PE_{1},\;PE_{2})$.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.4
• /
• pp.506-521
• /
• 2007

Statement of problem: The cumulative success rate of wide implant is still controversial. Some previous reports have shown high success rate, and some other reports shown high failure rate. Purpose: The aim of this study was to analyze, and compare the biomechanics in wide implant system embeded in different width of crestal bone under different occlusal forces by finite element approach. Material and methods: Three-dimensional finite element models were created based on tracing of CT image of second premolar section of mandible with one implant embedded. One standard model (6mm-crestal bone width, 4.0mm implant diameter central position) was created. Varied crestal dimension(4, 6, 8 mm), different diameter of implants(3.3, 4.0, 5.5, 6.0mm), and buccal position implant models were generated. A 100-N vertical(L1) and 30 degree oblique load from lingual(L2) and buccal(L3) direction were applied to the occlusal surface of the crown. The analysis was performed for each load by means of the ANSYS V.9.0 program. Conclusion: 1. In all cases, maximum equivalent stress that applied $30^{\circ}$ oblique load around the alveolar bone crest was larger than that of the vertical load. Especially the equivalent stress that loaded obliquely in buccal side was larger. 2. In study of implant fixture diameter, stress around alveolar bone was decreased with the increase of implant diameter. In the vertical load, as the diameter of implant increased the equivalent stress decreased, but equivalent stress increased in case of the wide implant that have a little cortical bone in the buccal side. In the lateral oblique loading condition, the diameter of implant increased the equivalent stress decreased, but in the buccal oblique load, there was not significant difference between the 5.5mm and 6.0mm as the wide diameter implant. 3. In study of alveolar bone width, equivalent stress was decreased with the increase of alveolar bone width. In the vertical and oblique loading condition, the width of alveolar bone increased 6.0mm the equivalent stress decreased. But in the oblique loading condition, there was not a difference equivalent stress at more than 6.0mm of alveolar bone width. 4. In study of insertion position of implant fixture, even though the insertion position of implant fixture move there was not a difference equivalent stress, but in the case of little cortical bone in the buccal side, value of the equivalent stress was most unfavorable. 5. In all cases, it showed high stress around the top of fixture that contact cortical bone, but there was not a portion on the bottom of fixture that concentrate highly stress and play the role of stress dispersion. These results demonstrated that obtaining the more contact from the bucco-lingual cortical bone by installing wide diameter implant plays an important role in biomechanics.

• Strategy21
• /
• s.46
• /
• pp.89-122
• /
• 2020

The longing for submarine manufacture and the fear of her power had exited for a long time, but submarine that could submerge and attack was built from 20th century by science technology development. The question, 'Submarine can exercise her power in naval warfare?' had exited before World War I, but the effective value of submarine was shown in the procedure of a chain of naval warfare during World War I and World War II. Germany and the United States made the best use of submarines at that time. The submarines of these nations mounted fierce attack on the enemy's battleships and merchant ships and blocked the sea lanes for war material. These fierce attack on ships became impossible After World War II, and the major powers reduced and coordinated the defence budget, so they considered the role of submarine. However, submarine is still powerful weapon system because she can secretly navigate under the water, and one of the most important force in the navy. The aim of this thesis is analyzing submarine roles in each naval warfare and integrating maritime strategy and weapon system technology into her roles. First, the research about represent submarine roles like anti-surfaceship warfare, anti-submarine warfare, intelligence gathering, land attack, supporting special operation and mine landing warfare will be presented, then the major naval warfare where submarine participated(during ex-World War I, World War I, World War II, The Cold War Era and post Cold War) and the analyzing of submarine roles by time will be presented. Submarine was developed for anti-surfaceship warfare during ex-World War I but could not make remarkable military gain in naval warfare because her performance and weapon was inadequate. However, the effective value of submarine in the procedure of a chain of naval warfare was shown during World War I and World War II. The major powers put battleships into naval warfare undiscriminatingly to command the sea power and submarines did massive damage to enemy navy power, so put a restraint the maritime power of enemy, and blocked the sea lanes for war material. After World War II, the battlefield situation changed rapidly and the concept of preemption became difficult to apply in naval warfare. Therefore, the submarine was unable to concentrate on anti-surfaceship mission. Especially during the Cold War era, nuclear submarine came to appear and her weapon system developed rapidly. These development gave submarines special missions: anti-submarine warfare and intelligence gathering. At that time, United States and Soviet submarines tracked other nation's submarines loaded with nuclear weapons and departing from naval their base. The submarines also collected information on the volume of ships and a coastal missile launching site in company with this mission. After Cold War, the major powers despatched forces to major troubled regions to maintain world peace, their submarines approached the shores of these regions and attacked key enemy installations with cruise missiles. At that time, the United States eased the concept of preemption and made the concept of Bush doctrine because of possible 911 terrorism. The missiles fired from submarines and surface battleships accurately attacked key enemy installations. Many nations be strategically successful depending on what kind of mission a submarine is assigned. The patterns of future naval warfare that my country will provide against will be military power projection and coalition/joint operations. These suggest much more about what future missions we should assign to submarines.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.4
• /
• pp.81-89
• /
• 2009

The seepage should be analyzed to design or reinforce the levees. The steady seepage analysis is an usual application in USA and European countries where the large scaled dams and levees are existed. However, Korea and Japan, where the reaching time is short, the excessive forces are applied on the levees at the short reaching time if the seepages are analyzed in steady condition. Accordingly, the unsteady analysis based on the variation of time is necessitated. In the unsteady analysis, the flood wave type is necessary. No criteria and standards, however, are derived for the unsteady seepage in Korea. In the study, the flood wave type is derived for the unsteady seepage. The major reliable flood surface data are collected in 5 stations including Jindong of the Nakdong river basin. The data are sorted in duration, and they are non-dimensionalized. The statistical method is also applied to derive the waves. To verify the study, the seepage is analyzed by the derived wave and applied to the prototype. The results are also compared with the Japanese Method. The errors between the hydraulic gradient and critical velocity method are $0{\sim}0.7%$, $0{\sim}0.7%$ at the Jindong, $1.6{\sim}4.0%$, $1.7{\sim}4.1%$ at the Hyunpoong, $0.6{\sim}3.6%$, $0.6{\sim}3.7%$ at the Waegwan, $2.0{\sim}8.1%$, $2.0{\sim}8.1%$ at the Nakdong, and $1.2{\sim}9.8%$, $1.3{\sim}9.9%$ at the Jeongam, respectively. The relationship($R^2$) between each method is relatively high as $0.983{\sim}0.999$. This means the results are more logical than the Japanese method, and the study is applicable to the design of hydraulic structures.