• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.25-32
• /
• 1997

The neural network was applied to identify wear debris generated from the lubricated machine moving surface. The wear test was carried out under different experimental conditions. In order to describe characteristics of debris of various shapes and sizes. The four parameter(50% volumetric diameter, aspect, roundness and reflec- tivity) of wear debris are used as inputs to the network and learned the friction condition of five values (material 3, applied load 1, sliding distance 1). It is shown that identification results depend on the ranges of these shape parameter learned. The three kinds of the wear debris had a different pattern characteristic and recognized the friction condition and materials very well by neural network.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.10
• /
• pp.45-51
• /
• 2010

Electrical discharge drilling (ED-drilling) is a widespread machining method used to bore small holes with a high aspect ratio. This paper presents additional methods by which ED-drilling can improve machining speed, tool wear, and machined surface quality. Firstly, for high machining speed, and low tool wear, a new-type electrode that was ground on one side or both sides of the cylindrical electrodes was suggested to expel debris. The debris which is generated during the machining process can cause sludge deposition and secondary discharge problems: major reasons to decrease machining speed. This new-type electrode also reduced tool wear that was due to the decrease of unstable discharge in a machining gap by helping to expel waste water and debris from the gap. Secondly, to improve the machined surface roughness, an electrolyzation process was included after drilling. This process made the machined surface smooth by means of an electrochemical reaction between an electrode and a workpiece. In this study, the machining speed, electrode wear, and surface roughness were improved by the newtype electrode and the electrolytic process.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.3 s.16
• /
• pp.5-10
• /
• 2006

This paper investigates cutting qualities after laser dicing and predicts the problems that can be generated by laser dicing. And through 3 point bending test, die strength is measured and the die strength after laser dicing is compared with the die strength after mechanical sawing. Laser dicing is chiefly considered as an alternative to overcome the defects of mechanical sawing such as chipping on the surface and crack on the back side. Laser micromachining is based on the thermal ablation and evaporation mechanism. As a result of laser dicing experiments, debris on the surface of wafer is observed. To eliminate the debris and protect the surface, an experiment is done using a water soluble coating material and ultrasonic. The consequence is that most of debris is removed. But there are some residues around the cutting line. Unlike mechanical sawing, chipping on the surface and crack on the back side is not observed. The cross section of cutting line by laser dicing is rough as compared with that by mechanical sawing. But micro crack can not be seen. Micro crack reduces die strength. To measure this, 3 point bending test is done. The die strength after laser dicing decreases to a half of the die strength after mechanical sawing. This means that die cracking during package assembly can occur.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2420-2427
• /
• 2000

In contacting between surface, there is wear and the generation of wear particles. The particles contained in the lubricating oil carry detailed and important information about the condition monitoring of the machine. Therefore, This paper was undertaken for Ferrography system of wear debris generated from lubricated moving machine surface. The lubricating wear test was performed under different experimental conditions using the Falex wear test of Pin and V-Block type by Ti(C,N) coated. It was shown from the test results that wear particle concentration(WPC) ; wear severity Index(IS) and size\distribution have come out all the higher value by increases sliding friction time. By the Ferrogram a thin leaf wear debris as well as ball and plate type wear particles was observed.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.2
• /
• pp.89-100
• /
• 2012

The aim of this study knows to occurrence characteristics and monthly transition of foreign marine debris by changing in the marine environment for the national marine debris monitoring areas in the west coastal area. The Jeju Island (5,112) had the highest number for foreign marine debris flowed in the coast. Many areas in the next were surveyed by Hajo Island (1,967), Imja Island (507). Plastic bottles were the most common type to 2,925 piece of the whole collection. Then, the monthly occurrence amount was concentrated in July, September. At this time, analysis results of the marine environment are as follows: The sea surface wind of southerly or southeasterly were predominated. In addition, the sea surface circulations were dominated by inflow of seawater southward along the China Coast and northward from the East China Sea.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.12
• /
• pp.191-197
• /
• 2003

As mechanical components are miniaturized, the demand on micro die and mold is increasing. Micro mechanical components usually have high hardness and good conductivity. So micro electrical discharge machining (MEDM) is an effective way to machine those components. In micro cavity fabrication using MEDM, it is observed that the bottom surface of cavity is distorted. Electric charges tend to be concentrated at the sharp edge. At the center of the bottom surface, debris can not be drawn off easily. These two phenomena make the bottom surface of the electrode and workpiece distort. As machining depth increases, the distorted shape of electrode approaches hemisphere. This process is affected by capacitance and the size of electrode. By using a smaller electrode than the desired cavity size and appropriate tool movement, bottom shape distortion can be prevented.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.4
• /
• pp.44-48
• /
• 2005

As mechanical components are miniaturized, the demands on micro die/mold are increasing. Micro mechanical components usually have high hardness and good conductivity. Micro electrical discharge machining (MEDM) can thus be an effective way to machine those components. In micro cavity fabrication using MEDM, it is observed that the bottom surface of the cavity is distorted. Electric charges tend to be concentrated at the sharp edge, and debris cannot be drawn off easily at the center of the bottom surface. These two phenomena make the bottom surface of electrode and workpiece distort. As machining depth increases, the distorted shape of the electrode approaches hemisphere. This process is affected by both capacitance and the size of electrode. By using a smaller electrode than the desired cavity size and appropriate tool movement, bottom shape distortion can be prevented.

• Journal of The Geomorphological Association of Korea
• /
• v.28 no.3
• /
• pp.13-26
• /
• 2021

In mountain gully, channelized debris flow is an important phenomenon in the process of topographical change. Social infrastructure as roads may be damaged by channelized debris flows, but there has been little information about their occurrence and movement to prepare for the risk of the debris flow. Most of the channelized debris flows occur during heavy rains in mountainous valleys that are difficult to access, so there are not many field data. In this study, the topographical characteristics of the catchment, the rainfall and runoff related to the debris flow, the sedimentary pattern and the cross-sectional change of the channel bed, and the underflow velocity of the gravel bed have been investigated and analyzed in the Singi gully where the channelized debris flows occurred. In the catchment, there was almost no sediment runoff because the vegetation combine with the debris landforms and covered the surface. Therefore, the obvious cause of the channelized debris flows is the collapse of the slope and bed of the gully. Even if the gravel, cobbles, and boulders of the channel bed were lost by debris flow, the thalweg change due to debris flow may not be significant because they are supplied from the gully side slope normally. After the gabion structures were installed, the debris flow increased the thalweg change, bed erosion and side slope of the gully. Various sedimentary structures in the gully were classified according to the factors supporting the sedimentation. The hypsometric curve of the gully reflects the debris landforms and vegetation characteristics of the watershed and the sediment runoff due to debris flow, etc. The relationship between the flow velocity and the hydraulic gradient was non-linear under the condition that the porous medium with gully bed gravels is saturated with water. These results may be used as basic data for channelized debris flow research.

• Journal of Fisheries and Marine Sciences Education
• /
• v.9 no.1
• /
• pp.31-39
• /
• 1997

Floating debris was recorded from a training ship, #1 Kwanaksan, of Pukyong National University with about 10 knots speed during August 19~26, 1996. The area sampled is the East Coast of Korea, divided into 33 unit segments on survey routes. Debris fabrication materials were categorized using the following; man-made or natural wood items, paper, cardboard, nylon rope, netting, styrofoam and plastics, floating metal and glass containers. All identified items within a $100{\pm}2m$ wide band were recorded but ignored if beyond this boundary. The results of distribution and composition of floating debris in the area are as follows: 1. The quantities of debris during the summer were distributed from 1.8~52 items per $km^2$. The most obvious trend is the widespread distribution of all debris. 2. The highest densities of all debris were discovered in the vicinity of Pusan and ills an area. Especially styrofoam & plastics were observed in 81% of sampled area, next is wood items, 9.1%. Nylon netting & rope was the least widespread pollutant. 3. The relationship between distribution of debris and surface currents of the area was not apparently revealed through this survey. Further surveys are being instigated, and from this it is hoped that a much wider coverage can be achived, perhaps on all sites of Southern and Western sea of Korea and contributed to the finding of sources,stationary area of debris.

• The Journal of Bigdata
• /
• v.8 no.1
• /
• pp.73-82
• /
• 2023

Marine debris not only affects the survival of marine life, water pollution, and scenery but also has secondary effects on economic loss and human health. While research on underwater and surface debris is actively ongoing, solutions to marine debris in hard-to-reach blind spots are being developed slowly. To address this problem, we utilize drones to detect and track marine debris in blind spots such as tetrapods. The detected debris is then visualized by calculating its location coordinates using the drone's GPS, altitude, and heading values. The proposed method of using drones for detecting marine debris and matching it with longitude and latitude coordinates provides an effective solution to the problem of marine debris in blind spots.