• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.302-314
• /
• 2016

This study was carried out to confirm the effects of the knife-incising and kerfing pretreatment on the moisture content and surface check occurrence of Douglas-fir heavy timber. In the case of moisture content, the moisture gradient that formed in the inner part of the specimen was observed in all specimens. In addition, the moisture gradient was formed differently from the surface layer to 72 mm depending on the pretreatment conditions, and it was formed gradually in the kerfing than the knife-incising. In addition, it was found that the solid volume should be considered when measuring the average moisture content. In the case of surface check, the surface check occurrence was reduced in the knife-incising, kerfing, and the combination of knife-incising and kerfing than the control. In particular, the kerfing treatment was shown that the expansion of surface check width was effectively suppressed. In the case of knife-incising treatment, although the surface check was less than the control, the preventive effect on the surface check occurrence did not reach the level of the kerfing treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.107-115
• /
• 2017

In this study, the surface check reduction effect of preservative-treated Korean larch round-wood was investigated by applying three physical treatments, such as incising, kerfing, and kiln-drying. Moreover, the possibility of long-term service life was also checked by comparing the depth of surface check and the penetration depth of preservative. A rapid gradient of wood moisture content between surface and center causes a surface check. Thus, the effect of reducing surface check was carried out at the lowest equilibrium moisture content (EMC) condition, temperature ($2^{\circ}C$), humidity (44.6%), in outdoor locations in Korea until the test specimens reach to the 8.6% EMC. As a result, the preservative-treated specimens without incising, kerfing, kiln-drying (Type C) could not ensure the long-term service life due to a large surface check. Because the surface check depth of all specimens was deeper than the penetration depth of preservative. In case of the incising treated specimens (Type I), 80% of them, the depth of surface check was not deeper than the penetration depth of preservative. However, when a kerfing was additionally treated (Type B), a possibility of happening deeper surface check than penetration depth of preservative was increased rather than Type I.

• Transactions of Materials Processing
• /
• v.6 no.5
• /
• pp.416-424
• /
• 1997

In the present study, a contact search and check algorithm for general tool surface described by triangular FE patch is proposed. To improve numerical stability, SEAM element using the linear Coons interpolation has been used. To check the proposed algorithm, both clover cup and L-shape cup deep drawing processes are calculated. The computed results shows that the proposed contact algorithm can be successfully applied for sheet metal forming processes with general shaped tools.

• Korean Journal of Acupuncture
• /
• v.25 no.2
• /
• pp.115-123
• /
• 2008

Objectives : The aim of this stuty is to investigate the effect of acupuncture at $Yanggn\bar{u}ngch'\check{o}n$ (G34) on the muscle fatigue. Methods : Subjects were asked to perform the elbow flexion and extension to induce the muscle fatigue. Sample group of 16 healthy subjects had acupuncture on $Yanggn\bar{u}ngch'\check{o}n$ (G34) during the resting time, while control group of 13 healthy subjects did not. Surface electromyography (sEMG) was measured after exercise and rest to record muscle fatigue. Results : Acupuncture at $Yanggn\bar{u}ngch'\check{o}n$ (G34) is effective for decreasing the muscle fatigue.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.121-124
• /
• 1997

In the present study, a general tool surface contac search ad check algorithm is proposed. A general tool surface is described by triangular FE mesh. To check a proposed algorithm, clover cup and L-shape cup deep drawing processes are calculated. The elastic-plastic FEM using SEAM (Shear Energy Augmented Membrane) element is adapted for numerical stability.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.10
• /
• pp.105-111
• /
• 2003

ORVR filler neck check valve, which is one of the essential components of the vapor fuel control system, should diminish the evaporation by maintaining laminar fluid flow on refueling process. This study presents numerical. results of pressure and velocity distributions of the fluid flow in a ORVR filler neck check valve on refueling process. CFD-ACE+ has been employed for numerical analysis based on the information of experimental results of valve position as a function of inlet flow rate. No abrupt pressure change, which may causes vaporization of fuel, has been confirmed to take place on the concave surface of the valve spool. However, it is clear that some possibility exist at the mid-position of surface of valve spool and downstream according to the opening of valve.

• Journal of Korean Medicine Rehabilitation
• /
• v.24 no.3
• /
• pp.29-37
• /
• 2014

Objectives Osteoporosis is an impending problem in the rapidly aging society. The purpose of this study is to identify the effects of Yoohyangheukho-dan ($R{\check{u}}xi{\bar{a}}ngh{\bar{e}}ih{\check{u}}-d{\bar{a}}n$) on osteoporosis induced by ovariectomy in rats. Methods 24 rats were randomly assigned to a SHAM group, a control group, and a Yoohyangheukho-dan ($R{\check{u}}xi{\bar{a}}ngh{\bar{e}}ih{\check{u}}-d{\bar{a}}n$) group (n=8). Ovaries were extracted and for 8 weeks, the rats were given dry feeds and Yoohyangheukho-dan ($R{\check{u}}xi{\bar{a}}ngh{\bar{e}}ih{\check{u}}-d{\bar{a}}n$) group were given a mixture of dry feeds and Yoohyangheukho-dan ($R{\check{u}}xi{\bar{a}}ngh{\bar{e}}ih{\check{u}}-d{\bar{a}}n$). At 8 weeks, their body weight, femur mass, tibia ash per body ratio, overall surface area and thickness of the trabeculae, overall surface area of the osteoblasts, and the number of osteoclasts were measured and levels of albumin, aspartate transaminase (AST), alanine transaminase (ALT), alkaline phosphatase (ALP), total-cholesterol, calcium and estradiol were recorded. Results There was no significant difference in the weight of the femur and the tibia ash per body ratio. The Yoohyangheukho-dan ($R{\check{u}}xi{\bar{a}}ngh{\bar{e}}ih{\check{u}}-d{\bar{a}}n$) group had significantly thicker trabeculae than the control group and showed a minimal increase of overall surface area of the trabeculae. The overall surface area of the osteoblasts and the number of osteoclasts decreased in the Yoohyangheukho-dan ($R{\check{u}}xi{\bar{a}}ngh{\bar{e}}ih{\check{u}}-d{\bar{a}}n$) group. There were no statistically significant differences in AST, ALT, ALP, total cholesterol, phosphorus, and estradiol levels. On the contrary the Yoohyangheukho-dan ($R{\check{u}}xi{\bar{a}}ngh{\bar{e}}ih{\check{u}}-d{\bar{a}}n$) group had significantly higher levels of Albumin, triglyceride, and calcium. Conclusions It can be concluded that oral intake of Yoohyangheukho-dan ($R{\check{u}}xi{\bar{a}}ngh{\bar{e}}ih{\check{u}}-d{\bar{a}}n$) prevents the thinning process of the trabeculae. Thus, it may have positive effects on the treatment and prevention of osteoporosis in postmenopausal women.

• Journal of the Korean Wood Science and Technology
• /
• v.4 no.1
• /
• pp.15-20
• /
• 1976

This is the abstract of the study on the check by static driving nail in Pinus koraiensis Sieb. et Zucc., Abies holophylla Maximowicz, and Larix leptolepis Gordon Pinet. which are commercial woods and main forestation species in Korea. The static driving resistance of nail is decresed straightly and the surface and back check's length and width were increased in proportion to increase of the moisture content, but the surface check length and width were over twice as large as the back check, also the check were happened in order of Pinus koraiensis Sieb. et Zucc., Abies holophylla Maximowicz., and Larix leptolepis Gordon Pinet. As the driving nail speed was increased, surface check length and width were increased and the back check was over twice as large as the surface check.

• International Journal of CAD/CAM
• /
• v.7 no.1
• /
• pp.51-60
• /
• 2007

This paper presents an algorithm of optimal cutting tool selection for machining of the point-based surface that is defined by a set of surface points rather than parametric polynomial surface equations. As the ball-end and fillet-end mills are generally used for finish machining in a 3-axis computer numerical control machine, the algorithm is applicable for both cutters. The optimum tool would be as large as possible in terms of the cutter radius and/or corner radius which maximise (s) the material removal rate (i.e., minimise (s) the machining time), while still being able to machine the entire point-based surface without gouging any surface point. The gouging are two types: local and global. In this paper, the distance between the cutter bottom and surface points is used to check the local gouging whereas the shortest distance between the surface points and cutter axis is effectively used to check the global gouging. The selection procedure begins with a cutter from the tool library, which has the largest cutter radius and/or corner radius, and then adequacy of the point-density is checked to limit the accuracy of the cutter selection for the point-based surface within tolerance prior to the gouge checking. When the entire surface is gouge-free with a chosen cutting tool then the tool becomes the optimum cutting tool for a list of cutters available in the tool library. The effectiveness of the algorithm is demonstrated considering two examples.

• Atmosphere
• /
• v.22 no.3
• /
• pp.299-307
• /
• 2012

This study is aimed to validate errors for detected suspicious temperature data using various quality control procedures for 61 weather stations in the Republic of Korea. The quality control algorithms for temperature data consist of four main procedures (high-low extreme check, internal consistency check, temporal outlier check, and spatial outlier check). Errors of detected suspicious temperature data are judged by examining temperature data of nearby stations, surface weather charts, hourly temperature data, daily precipitation, and daily maximum wind direction. The number of detected errors in internal consistency check and spatial outlier check showed 4 days (3 stations) and 7 days (5 stations), respectively. Effective and objective methods for validation errors through this study will help to reduce manpower and time for conduct of quality management for temperature data.