• The Journal of Advanced Prosthodontics
• /
• 제9권1호
• /
• pp.31-37
• /
• 2017

PURPOSE. The purpose of this study was to analyze the influence of the platform switching concept on an implant system and peri-implant bone using three-dimensional finite element analysis. MATERIALS AND METHODS. Two three-dimensional finite element models for wide platform and platform switching were created. In the wide platform model, a wide platform abutment was connected to a wide platform implant. In the platform switching model, the wide platform abutment of the wide platform model was replaced by a regular platform abutment. A contact condition was set between the implant components. A vertical load of 300 N was applied to the crown. The maximum von Mises stress values and displacements of the two models were compared to analyze the biomechanical behavior of the models. RESULTS. In the two models, the stress was mainly concentrated at the bottom of the abutment and the top surface of the implant in both models. However, the von Mises stress values were much higher in the platform switching model in most of the components, except for the bone. The highest von Mises values and stress distribution pattern of the bone were similar in the two models. The components of the platform switching model showed greater displacement than those of the wide platform model. CONCLUSION. Due to the stress concentration generated in the implant and the prosthodontic components of the platform switched implant, the mechanical complications might occur when platform switching concept is used.

• Coupled systems mechanics
• /
• 제7권4호
• /
• pp.455-483
• /
• 2018

The study deals with physical modeling of a typical three storeyed building frame supported by a pile group of four piles ($2{\times}2$) embedded in cohesive soil mass using three dimensional finite element analysis. For the purpose of modeling, the elements such as beams, slabs and columns, of the superstructure frame; and that of the pile foundation such as pile and pile cap are descretized using twenty noded isoparametric continuum elements. The interface between the pile and the soil is idealized using sixteen node isoparametric surface element. The soil elements are modeled using eight nodes, nine nodes and twelve node continuum elements. The present study considers the linear elastic behaviour of the elements of superstructure and substructure (i.e., foundation). The soil is assumed to behave non-linear. The parametric study is carried out for studying the effect of soil- structure interaction on response of the frame on the premise of sub-structure approach. The frame is analyzed initially without considering the effect of the foundation (non-interaction analysis) and then, the pile foundation is evaluated independently to obtain the equivalent stiffness; and these values are used in the interaction analysis. The spacing between the piles in a group is varied to evaluate its effect on the interactive behaviour of frame in the context of two embedment depth ratios. The response of the frame included the horizontal displacement at the level of each storey, shear force in beams, axial force in columns along with the bending moments in beams and columns. The effect of the soil- structure interaction is observed to be significant for the configuration of the pile groups and in the context of non-linear behaviour of soil.

• 마이크로전자및패키징학회지
• /
• 제10권3호
• /
• pp.37-42
• /
• 2003

전자 패키징에 사용되는 솔더합금에 납을 함유됨으로써 인하여 야기되는 환경적 문제와 인체 유해성 때문에 Pb-Sn 합금계를 대체할 수 있는 새로운 무연 솔더 재료의 필요성이 대두되고 있다. 새로운 솔더합금의 개발에 있어서 솔더 조인트의 신뢰성이 가장 중요한 문제라고 할 수 있는데, 솔더 조인트의 신뢰성은 솔더와 기판 사이의 계면 반응 형태와 그 정도에 의해서 크게 영향을 받기 때문에 솔더와 기판 사이의 계면 현상에 관한 더 깊은 이해가 필요하게 된다 솔더링 동안 기판/솔더 계면에서 가장 먼저 생성되는 금속간 화합물의 상을 예측하기 위한 열역학적인 방법이 제안되었다. 계면 에너지와 석출 구동력의 함수로 표현되는 각각의 금속간 화합물에 대한 핵생성 활성화 에너지를 비교함으로써 활성화 에너지가 가장 낮은 금속간 화합물이 가장 먼저 생성된다고 예측하였다. 거기에 더해 에너지를 기반으로 한 계산을 통하여 솔더 조인트에서 금속간 화합물의 입자 형상을 설명하였다. 울퉁불퉁한 계면을 가진 금속간 화합물의 Jackson의 parameter 값은 2보다 작은 반면 평평한 입자의 경우 2보다 크게 된다.

• 한국재료학회지
• /
• 제10권8호
• /
• pp.551-557
• /
• 2000

구리계 리드페임의 표면에 흑생산화물을 형성시키기 위하여 알칼리 용액에 담궈 산화시킨후 EMC(epoxy molding compound)로 몰딩하였고 기계적 가공을 하여 SDCB(sandwiched double-cantilever beam) 및 SBN(sandwiched Brazil-nut)시편을 만들었다. SDCB와 SBN 시편은 리드프레임/EMC 계면의 접착력을 각각 준 mode I 하중 및 혼합모드 하중 하에서 파괴인성치로 측정하기 위하여 고안되었다. 파괴경로를 밝혀내기 위하여 접착력 츨정 후에 얻어진 파면에 대하여 glancing-angle XRD, SEM, AFM, EDS 및 AES를 이용하여 분석하였다. SDCB 실험 후의 파면은 파괴되는 양상에 따라 세 가지 형태로 나눌 수 있었으며, 각 형태는 리드프레임의 접착전 표면 산화물 형성 상태와 밀접한 관계가 있었다. SBN 실험 후의 파면은 균열에서 가까운 부분과 먼 부분으로 나누어지는 특징을 보였는데, 이는 동적 파괴 효과(dynamic fracture effect)에 기인하는 것이라 생각된다. 또한 위상각에 따라 확실히 다른 파괴 양상을 보였는데, 이는 위상각에 따라 mode II 성분이 변하기 때문으로 생각된다.

• 한국재료학회지
• /
• 제14권6호
• /
• pp.402-406
• /
• 2004

$WSi_2$, $TiSi_2$, $CoSi_2$, and $TaSi_2$ are general silicides used today in semiconductor devices. $WSi_2$ thin films have been proposed, studied and used recently in CMOS technology extensively to reduce sheet resistance of polysilicon and $n^{+}$ region. However, there are several serious problems encountered because $WSi_2$ is oxidized and forms a native oxide layer at the interface between $WSi_2$ and $Si_3$$N_4$. In this study, we have introduced 20 $slm-N_2$ gas from top to bottom of the furnace in order to control native oxide films between $WSi_2$ and $Si_3$$N_4$ film. In resulting SEM photographs, we have observed that the native oxide films at the surface of $WSi_2$ film are removed using the long injector system.

• Ocean and Polar Research
• /
• 제29권4호
• /
• pp.349-366
• /
• 2007

Seasonal variations of various physicochemical components (temperature, salinity, pH, DO, COD, DOC, nutrients-silicate, DIN, DIP) and potential limiting factor for phytoplankton primary production were studied in the surface water of semi-enclosed Masan Bay. Seasonal variations of nutrient concentrations, with lower values in summer and winter, and higher in fall, are probably controlled by freshwater loadings to the bay, benthic flux and magnitude of occurrence of phytoplankton communities. Their spatial distributional patterns are primarily dependent on physical mixing process between freshwater and coastal seawater, which result in a decreasing spatial gradient from inner to outer part of the bay. In the fall season of strong wave action, the major part of nutrient inputs (silicate, ammonium, dissolved inorganic phosphorus) comes from regeneration (benthic flux) at sediment-water interface. During the summer period, high Si:DIN and Si:DIP and low DIN:DIP relative to Redfield ratios suggest a N- and secondarily P-deficiency. During other seasons, however, silicate is the potential limiting factor for primary production, although the Si-deficiency is less pronounced in the outer region of the bay. Indeed, phytoplankton communities in Masan Bay are largely affected by the seasonal variability of limiting nutrients. On the other hand, the severe depletion of DIN (relatively higher silicate level) during summer with high freshwater discharge probably can be explained by N-uptake of temporary nanoflagellate blooms, which responds rapidly to pulsed nutrient loading events. In Masan Bay, this rapid nutrient consumption is considerably important as it can modify the phytoplankton community structures.

• 대한치과보철학회지
• /
• 제39권1호
• /
• pp.1-13
• /
• 2001

An absolutely passive fit at the interface with the superstructure and the abutment cylinders is need for implant longevity. In this study, a method of cast framework correction using spark erosion technology was evaluated. Electric discharge machining(EDM) is a process that uses electrical discharges, or sparks, to machine metal, The surface being machined is bombared with high-intensity electrical energy pulses that gradually melt away the stock until the desired configuration is obtained. Master model was fabricated by using metal block impression analogue, which fired 5 Branemark squared impression coping in an arc shaped metal block. Then framework using 4mm standard gold cylinder and type IV gold alloy was fabricated. In order to measure the fit of the framework we used both contact and noncontact coordinate measurement machine and data was processed by computer program. After superimposition of gold framework and master model numeric image data the distances between gold cylinder bearing surfaces and abutment replica bearing surfaces, and the angle deviations between gold cylinder and abutment replica centroid points were calculated. The results were as follows 1 The total mean distance (p<0.01) and standard deviation (p<0.001) between the gold cylinders and abutment bearing surfaces were significantly decreased after EDM 2. The total mean of maximum distances was significantly decreased after EDM (p<0.05). 3. After EDM, the mean angle deviation between centroid points was decreased.

• 대한전자공학회논문지SD
• /
• 제47권2호
• /
• pp.68-76
• /
• 2010

최근 터치스크린 기술은 인간이 컴퓨터와 대화할 수 있는 주요 도구로서 급진적인 발전을 이루고 있다. 이 사용자 친화적인 인터페이스는 휴대폰에 이어 데스크탑, TV와 같은 대형스크린 시장까지 확산되어가고 있지만 기존의 저항막방식, 정전용량방식, 초음파방식 등은 기술 및 비용문제로 인하여 중 대형스크린에 적용하기 힘들다. 따라서 본 논문에서는 적외선과 라인스캔 이미지센서를 이용하여 간단하고 저렴한 비용으로 중 대형스크린에 적용할 수 있는 광학 영상 터치스크린 솔루션을 소개하고 이 기술이 갖는 문제점과 해결방안을 제시한다. 멀티 포인트를 추출하기 위한 주요 알고리즘은 범용프로세서를 이용하여 구현 시 약 34ms(29fps)가 소요되었으며 이는 휴먼인터페이스 디바이스로 사용되기에는 불충분하였다. 이를 해결하기 위하여 본 논문에서는 신호처리 및 좌표추출연산을 위한 하드웨어를 설계하여 성능을 향상시키고 광학 영상 터치스크린이 갖는 문제점을 소프트웨어에서 효율적으로 처리할 수 있도록 하였다. 설계한 터치스크린 컨트롤러의 PSM(Power Saving Mode)은 1.8Wh의 적외선 소비에너지를 0.0072Wh 까지 개선하였으며 60인치 대형스크린에서 2개의 실제 좌표를 200fps 속도로 연산해낸다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.93-93
• /
• 2010

Semiconductor nanocrystal quantum dots (NQDs) have recently attracted considerable interest for use in photovoltaics. Band gaps of NQDs can be tuned over a considerable range by varying the particle size thereby allowing enhance absorption of solar spectrum. NQDs, synthesized using colloidal routes, are solution processable and promise for a large-area fabrication. Recent advancements in multiple-exciton generation in NQD solutions have afforded possible efficiency improvements. Various architectures have attempted to utilize the NQDs in photovoltaics, such as NQD-sensitized solar cell, NQD-bulk-heterojuction solar cell and etc. Here we have fabricated CdSe NQDs with the band gap of 1.8 eV to 2.1 eV on thin-layers of p-type organic crystallites (1.61 eV) to realize a donor-acceptor type heterojuction solar cell. Simple structure as it was, we could control the interface of electrode-p-layer, and n-p-layer and monitor the following efficiency changes. Specifically, surface molecules adsorbed on the NQDs were critical to enhance the carrier transfer among the n-layer where we could verify by measuring the photo-response from the NQD layers only. Further modifying the annealing temperature after the deposition of NQDs on p-layers allowed higher conversion efficiencies in the device.

• 대한금속재료학회지
• /
• 제49권10호
• /
• pp.811-817
• /
• 2011

In this study, we have investigated the role of a metal oxide hole injection layer (HIL) between an Indium Tin Oxide (ITO) electrode and an organic hole transporting layer (HTL) in organic light emitting diodes (OLEDs). Nickel Oxide films were deposited at different deposition times of 0 to 60 seconds, thus leading to a thickness from 0 to 15 nm on ITO/glass substrates. To study the influence of NiO film thickness on the properties of OLEDs, the relationships between NiO/ITO morphology and surface properties have been studied by UV-visible spectroscopy measurements and AFM microscopy. The dependences of the I-V-L properties on the thickness of the NiO layers were examined. Comparing these with devices without an NiO buffer layer, turn-on voltage and luminance have been obviously improved by using the NiO buffer layer with a thickness smaller than 10 nm in OLEDs. Moreover, the efficiency of the device ITO/NiO (< 5 nm)/NPB/$Alq_3$/ LiF/Al has increased two times at the same operation voltage (8V). Insertion of a thin NiO layer between the ITO and HTL enhances the hole injection, which can increase the device efficiency and decrease the turn-on voltage, while also decreasing the interface roughness.