• Applied Chemistry for Engineering
• /
• v.29 no.3
• /
• pp.318-324
• /
• 2018

In this study, PAN (polyacrylonitrile) based activated carbon fibers were prepared by water vapor activation method which is a physical activation method. Activation was performed with temperature and time as parameters. When the activation temperature reached 700, 750 and $800^{\circ}C$, the activation was carried out under the condition of a water vapor flow rate of 200 ml/min. In order to analyze the pore structure of activated carbon fibers, the specific surface area ($S_{BET}$) was measured by the adsorption/desorption isotherm of nitrogen gas and AFM analysis was performed for the surface analysis. Tensile tests were also conducted to investigate the effect of the pore structure on mechanical properties of fibers. As a result, the $S_{BET}$ of fibers after the activation showed a value of $448{\sim}902m^2/g$, the tensile strength decreased 58.16~84.92% and the tensile modulus decreased to 69.81~83.89%.

• Carbon letters
• /
• v.24
• /
• pp.36-40
• /
• 2017

Polyacrylonitrile/pitch nanofibers were prepared by electrospinning as a precursor for a gas sensor material. Pitch nanofibers were properly fabricated by incorporating polyacrylonitrile as an electrospinning supplement component. Polyacrylonitrile/pitch nanofibers were activated with steam at various temperatures followed by subsequent carbonization to make carbon nanofibers with a highly conductive graphitic structure. Steam activation was effective in facilitating gas adsorption onto the carbon nanofibers due to the increased surface area. The carbon nanofibers activated at $800^{\circ}C$ had a larger surface area and a lower micro pore fraction resulting in a higher variation in electrical resistance for improved CO gas sensing properties.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.223-226
• /
• 2005

For $CO_2-free$ hydrogen production and better utilization of the produced carbon, catalytic decomposition of methane over rubber-grade carbon blacks manufactured from coal tar was carried out. The catalytic activities of several domestic carbon blacks were compared. A pelletized carbon black exhibited considerably lower activity and activation energy than the fluffy( loose) carbon black of the same grade. This difference is considered due to the binder that was added during pelletization. For pelletized carbon blacks, a tendency was observed that the activity per unit mass of catalyst increased with the specific surface area of the carbon black. Another tendency was also observed that the activation energy increased with the primary particle size or decrease of the specific surface area.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.89-93
• /
• 1995

Effects of hydrogenation in amorphous silicon rile growths on Solid Phase Crystallization (SPC) was investigated using x-ray diffractometry, energy dispersive Spectroscopy, and Raman spectrum. Interdiffusion of barium(Ba) and aluminum(Al) compounds of corning substrate was observed in both of rf sputtering and LFCVD films under the low temperature(580$^{\circ}C$) annealing. Low degree of crystallinity resulted from the interdiffusion was obtained. Highly applicable degree of crystallinity was obtained through the mechanical damage induced surface activation on amorphous silicon films. X-ray diffraction intensity of (111) orientation was used to characterize the degree of crystallinity of SPC. Nucleation and growth rate in SPC could be controllable through the employed surface treatment. IIydrogenated LPCVD films showed the superior crystallinity to non-hydrogenated sputtering films. Insignificant effects of activation treatment in sputtered film was of activation treatment in sputtered film was observed on SPC.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.3
• /
• pp.131-137
• /
• 2007

The typical MCFC (molten carbonate fuel cell) anode is made of Ni-10%Cr alloy. The work of this paper is focused concerning long life of anode because Ni-10% Cr anode is suffering from sintering and creep behavior during cell operation. Therefore, Ni-coated Alumina powder($20{\mu}m$) was developed by electroless nickel plating. Optimum condition of electroless nickel coation on $20{\mu}m$ alumina is as follows: pH 11.7, temperature $65{\sim}80^{\circ}C$, powder amount $100cm^2/l$. The deposition rate for Ni-electroless plating was as a function of temperature and activation energy was evaluated by Arrhenius Equation thereby activation energy calculated slope of experimental data as 117.6 kJ/mol, frequency factor(A) was $6.28{\times}10^{18}hr^{-1}$, respectively.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.50 no.11
• /
• pp.550-556
• /
• 2001

The computerized cardiac analysis system, which acquires and analyzes the electrical activation signal propagating along the surface of the heart, is indispensible equipment for the open heart surgery and electrical cardiac study. In this paper, the design requirement and the electrical circuit analysis are performed to construct the multi-channel cardiac activation pre-amplifier necessary for a signal conditioning circuit. The general 64 channel configuration is expanded into 128 channels to enhance the spatial resolution on the mapped surface of the heart. The 128 channels pre-amplifier consists of input circuit, differential amplifier, right leg driven circuit and isolation part. It has distinct features; high voltage protection, leakage current limitation, isolation and the maximization of common mode rejection ratio with respect to the half-cell potential difference due to different electrode materials. The final pre-amplifier circuit is assembled with 8 boards, each of which composing of 16 channels.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.541-546
• /
• 2003

Activated carbon was prepared from coffee wastes by chemical activation with $ZnCl_{2}$, NaOH and KOH. The coffee wastes was used as raw material. Preparation process involves the roasting of raw material and carbonization of roasted material followed by chemical activation. N2-BET surface areas of activated coffee char prepared by chemical activation was measured as $1,110{\sim}2,442m^{2}/g$. Removal of copper and chromium in solution by activated carbon was carried out and structural change of pore surface was observed by SEM.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2010-2012
• /
• 2005

Activated carbon was activated with chemical treatment to attain high surface area with porous structure. We have been considered activated carbon is the ideal material for high voltage electric double layer capacitor due to their high specific surface area, good conductivity and chemical stability. In this study we found that increase in electrochemical capacitance due to activated carbon. Also chemically activated carbon and water treatment have resulted larger capacitance and also exhibits better electrochemical behavior, and is about 15% more than in untreated state. The structural change in activated carbon through chemical treatment activation was investigated by using SEM and XRD. In this study, the dependence of the activation behavior with KOH in the micro structure of host materials will be discussed. Furthermore, the relation to the electric double layer capacitance, especially the specific capacitance per unit area, is also discussed.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.181-182
• /
• 2015

본 실험에서는 PET 위 무전해 도금을 위한 대안 공정 개발을 목적으로 은(Ag)와 과망간산염($MnO_4{^-}$)를 사용하여 기존에 일반적으로 사용된 Sn/Pd의 Sensitization과 Activation process를 대체하는 기술을 연구했다. Palladium(Pd)의 경우 공정비용에서 높은 부분을 차지하기 때문에 이를 대신하여 Ag를 사용했으며, PET 표면의 전처리를 위해 Ultra Violet과 과망간 산염을 이용하여 표면의 친수성을 높였다. 과망간산염을 사용하여 표면을 전처리하는 과정에서 이산화망간($MnO_2$)과 알코올 작용기가 생성되는데 Ag activation 단계에서 촉매 생성에 중간 매개체 역할을 하는 것으로 사료된다. 이와 같은 결론을 도출 하기 위해서 표면 위 Ag의 화학적 구조 및 상 분석을 위해 XPS와 TEM이 사용되었으며 표면에서 Ag는 Ag-O와 같은 Silver oxide의 형태와 Ag-Mn-O와 같은 Compound로 무전해 도금을 위한 촉매 역할 하는 것으로 판단된다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.331-331
• /
• 2012

In this study, we investigated morphology observation of nanostructured Ti-25Ta-xZr alloys. Ti-25Ta-(3wt%~15 wt%) Zr alloys were prepared by a vacuum arc-melting furnace. Formation of nanotubular structure was achieved by an electrochemical method in 1M $H_3PO_4$ electrolytes containing 0.8%wt.% NaF. Nanotube morphology depended on alloying elements.