• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.12
• /
• pp.1189-1193
• /
• 2010

Mobility management is one of the most important research issues in 6LoWPAN, Since the IP-WSN application domain is expanded to real-time applications such as healthcare and surveillance systems, a fast and seamless handover becomes an important criterion in 6LoWPAN. However, a draft of IETF 6LoWPAN WG for mobility support does not decrease handover delay. Although LoWMob supports a fast intra-PAN handover. it can be supported when the infrastructure node has the location information of the other nodes in the mobile node's moving direction. In this paper, we propose a fast and seamless mobility protocol to support intra-PAN handover, named intra-MARIO. In intra-MARIO, a parent node of the mobile node preconfigures its handover to the PAN when the parent node detects its movement, thereby reducing the handover delay. Since intra-MARIO also supports route optimization, the mobile node can communicate with its corresponding nodes through the optimal route. In this paper, we analysis the signaling cost and evaluates that the handover can be completed in 20ms by simulation.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 1995.12a
• /
• pp.9-21
• /
• 1995

A planning support system enhances our ability to use water capacity expansion as an urban growth management strategy. This paper reports the development of capacity expansion modeling of water supply as part of the continuing development of such a planning support system (PEGASUS: Planning Environment for Generation and Analysis of Spatial Urban Systems) to incorporate water supply, This system is designed from the understanding that land use and development drive the demand for infrastructure and infrastructure can have a significant influence on the ways in which land is developed and used. Capacity expansion Problems of water supply can be solved in two ways: 1) optimal control theory, and 2) mixed integer nonlinear programming (MINLP). Each method has its strengths and weaknesses. In this study the MINLP approach is used because of its strength of determining expansion sizing and timing simultaneously. A dynamic network optimization model and a water-distribution network analysis model can address the dynamic interdependence between water planning and land use planning. While the water-distribution network analysis model evaluates the performance of generated networks over time, the dynamic optimization model chooses alternatives to meet expanding water needs. In addition, the user and capacity expansion modeling-to-generate-alternatives (MGA) can generate alternatives. A cost benefit analysis module using a normalization technique helps in choosing the most economical among those alternatives. GIS provide a tool for estimating the volume of demanded water and showing results of the capacity expansion model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.93-102
• /
• 2020

The design of large complex mechanical systems, such as automobile, aircraft, and ship, is a kind of Multidisciplinary Design Optimization (MDO) because it requires both experience and expertise in many areas. With the rapid development of technology and the demand to improve human convenience, the complexity of these systems is increasing further. The design of such a complex system requires an integrated system design, i.e., MDO, which can fuse not only domain-specific knowledge but also knowledge, experience, and perspectives in various fields. In the past, the MDO relied heavily on the designer's intuition and experience, making it less efficient in terms of accuracy and time efficiency. Process integration and the design optimization framework mainly support MDO owing to the evolution of IT technology. This paper examined the procedure and methods to implement an efficient MDO with reasonable effort and time using RCE, an open-source PIDO framework. As a benchmarking example, the authors applied the proposed MDO methodology to a bulk carrier's conceptual design synthesis model. The validity of this proposed MDO methodology was determined by visual analysis of the Pareto optimal solutions.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.1
• /
• pp.63-71
• /
• 2017

During the sea trial test, we discovered EMI(Electromagnetic Interference) between MIL-SATCOM parabolic antenna and ES(Electronic Warfare Support) omni antenna. Emitted side lobe of CW(Continuous Wave) from MIL-SATCOM raises the threshold level of ES omni antenna. Therefore detection rate of ES is decreased. To solve this problem, the path of side lobe of CW from MIL-SATCOM should be blocked using EMI shield. This paper presents the method how to calculate the size of EMI shield, material, and optimized deployment. The test of the EMI shield effect was performed on a surface ship. After installing EMI shield, EMI has been decreased significantly. This paper will provide a method how to design EMI shield and a way to verify the result.

• Journal of Computational Design and Engineering
• /
• v.3 no.4
• /
• pp.398-413
• /
• 2016

This work describes the design and development of a new drying system for a rollover carwash machine with the support of numerical tools. The drying system is composed of a pair of stationary vertical dryers and a moveable horizontal dryer that can adjust itself to the contour of a vehicle. After the definition of the dryers' concept, their performance was assessed individually to check their internal flow pattern and to improve their airflow distribution. These issues are expected to provide feedback on redesign and geometric optimization of the dryers. After redesign of the dryers separately, the behaviour of the complete drying system was studied on actual vehicle models, representative of the shortest and tallest dimensions that can be washed with the existing carwash machine sector. The drying efficiency of the whole system was studied by calculation of shear stress distribution on various surfaces of a given vehicle. The results allowed concluding that the overall drying performance of the design system is very good and assure adequate drying on most vehicles surfaces. The results obtained from numerical studies were then validated with experimental measurements and a good agreement was found between the two. The procedure employed in this work can be applied to support the design and analysis of other mechanical drying systems.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.64-71
• /
• 2017

Considering the volatility, intermittent and random of photovoltaic (PV) generation systems, accurate forecasting of PV power output is important for the grid scheduling and energy management. In order to improve the accuracy of short-term power forecasting of PV systems, this paper proposes a prediction model based on environmental factors and support vector machine optimized by genetic algorithm (GA-SVM). In order to improve the prediction accuracy of this model, weather conditions are divided into three types, and the gray correlation coefficient algorithm is used to find out a similar day of the predicted day. To avoid parameters optimization into local optima, this paper uses genetic algorithm to optimize SVM parameters. Example verification shows that the prediction accuracy in three types of weather will remain at between 10% -15% and the short-term PV power forecasting model proposed is effective and promising.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.11
• /
• pp.2824-2838
• /
• 2013

There has been a lot of attention paid recently to analyze dynamic human gestures that vary over time. Most attention to dynamic gestures concerns with spatio-temporal features, as compared to analyzing each frame of gestures separately. For accurate dynamic gesture recognition, motion feature extraction algorithms need to find representative features that uniquely identify time-varying gestures. This paper proposes a new feature-extraction algorithm using temporal self-similarity based on a hierarchical human model. Because a conventional temporal self-similarity method computes a whole movement among the continuous frames, the conventional temporal self-similarity method cannot recognize different gestures with the same amount of movement. The proposed model-based temporal self-similarity method groups body parts of a hierarchical model into several sets and calculates movements for each set. While recognition results can depend on how the sets are made, the best way to find optimal sets is to separate frequently used body parts from less-used body parts. Then, we apply a multiclass support vector machine whose optimization algorithm is based on structural support vector machines. In this paper, the effectiveness of the proposed feature extraction algorithm is demonstrated in an application for taebo gesture recognition. We show that the model-based temporal self-similarity method can overcome the shortcomings of the conventional temporal self-similarity method and the recognition results of the model-based method are superior to that of the conventional method.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.548-553
• /
• 2001

Recently, much attention is imposed on the design of the fuel assemblies in the Pressurized Light Water Reactor (PWR). Spacer grid is one of the main structural components in a fuel assembly. It supports fuel rods, guides cooling water and protects the system from the external impact loads. Various space grids have been proposed and new designs are also being created. In this research, a new spacer grid is designed by the axiomatic approach. The Independence Axiom is utilized for the design. For conceptual design, functional requirements (FRs) are defined and corresponding design parameters (DPs) are found to satisfy FRs in sequence. Overall configuration and shapes are determined in this process. Detail design is carried out based on the result of the axiomatic design. For the detail design, the system performances are evaluated by using linear and nonlinear finite element analysis. The dimensions are determined by optimization. Some commercial codes are utilized for the analysis and design.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1623-1630
• /
• 2002

Recently, much attention is imposed on the design of the fuel assemblies in the Pressurized Light Water Reactor (PWR). Spacer grid is one of the main structural components in a fuel assembly. It supports fuel rods, guides cooling water, and maintains a coolable geometry from the external impact loads. In this research, a new shape of the spacer grid is designed by the axiomatic approach. The Independence axiom is utilized for the design. For conceptual design, functional requirements (FRs) are defined and corresponding design parameters (DPs) are found to satisfy FRs in sequence. Overall configuration and shapes are determined in this process. Detail design is carried out based on the result of the axiomatic design. For the detail design, the system performances are evaluated by using linear and nonlinear finite element analysis. The dimensions are determined by optimization. Some commercial codes are utilized for the analysis and design.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.8
• /
• pp.623-628
• /
• 2000

Video-on-demand system in which users can request any video through the network at any time is made possible by rapid increase in network bandwidth and capacity of the media server. However true video-on-demand system cannot support all requests since bandwidth requirement is still too demanding. Therefore efficient bandwidth reduction algorithm is necessary. both the piggybacking method and the batching method are novel solutions that can provide more logical number of streams than the physical system can support. Of course each of them has its pros and cons. hence piggybacking with batching-by-size can take advantage of both the schemes. Some parameters such as the size of batch and the size of the catch-up window should be adjusted and order to maximize the bandwidth reduction for piggybacking with batching-by-size method. One of the most important parameters is decided optimally in this paper. Simulation shows that the optimized parameter can achieve considerable reductionand consequently remarkable enhancement in performance.