• Journal of the Korea Institute of Building Construction
• /
• v.17 no.3
• /
• pp.253-260
• /
• 2017

As global warming became a worldwide issue, a significant effort has been made on the development of technology related to $CO_2$ capture and storage. Geologic sequestration of $CO_2$ is one of those technologies for safe disposal of $CO_2$. Geologic sequestration stores $CO_2$ in the form of supercritical fluid into the underground site surrounded by solid rock, and concrete is used for prevention of $CO_2$ leakage into the atmosphere. In such case, concrete may experience severe damage by attack of supercritical $CO_2$, and especially in contact with underground water, very aggressive form of carbonation can occur. In this work, to prevent such deterioration in concrete, calcium phosphates were added to the portland cement to produce hydroxyapatite, one of the most stable mineral in the world. Temperature rise, viscosity, set and stiffening, and strength development of cement paste incorporating three different types of calcium phosphates were investigated. According to the results, it was found that the addition of calcium phosphate increased apparent viscosity, but decreased maximum temperature rise and 28 day compressive strength. It was found that monocalcium phosphate was found to be inappropriate for portland cement based material. Applicability of dicalcium and tricalcium phosphates for portland cement needs to be evaluated with further investigation, including the long term compressive strength development.

• Food Engineering Progress
• /
• v.15 no.2
• /
• pp.175-181
• /
• 2011

By using supercritical carbon dioxide fluid, an attempt was made to extract surface-active substances from defatted rice bran. Extraction was carried out according to D-optimal design and results were analyzed by response surface methodology to establish optimum condition. It was found that pressure, temperature and co-solvent (ethanol) influenced in a different extent on the extraction efficiency (i.e., yield and interfacial tension) of surface-active substances. Among them, co-solvent was found to be a major influencing factor, where maximum yield (2.62%) was observed at the highest content (250 g). In addition, it also affected most on the interfacial tension at the oil-water interface but in this case the lowest interfacial tension value (9.51 mN/m) was found when added lowest (50 g). In conclusion, it was estimated that the optimum extraction condition was to be pressure 350bar, temperature $62^{\circ}C$ and co-solvent content 50 g in this study, where extraction yield was 0.69% and interfacial tension to be 10.1 mN/m.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.1
• /
• pp.33-40
• /
• 2021

The objective of this work is to prove a possibility of void f illing through a carbonation f or the purpose of improving the quality of recycled aggregate. Carbonation can permanently immobilize CO2, which is a greenhouse gas, and thus provides additional benefit on environment. In this work, recycled fine aggregate was reacted using gaseous CO2 and supercritical CO2(scCO2) in a closed chamber, and the changes in physical properties of the recycled f ine aggregate bef ore and af ter carbonation were analyzed using the apparent density, skeletal density, pH, and FE-SEM measurements. Thereafter, a mortar specimen was prepared and a compressive strength was measured. According to the experimental results, it was found that the increase in the apparent density and the true density was higher by the reaction with scCO2, which was conducted at high temperature and high pressure compared to the reaction with gaseous CO2. In addition, the pH of the eluted water was found to have a larger initial decrease than that observed with samples from reaction by gaseous CO2. The shape and amount of calcium carbonate crystals were also found to be larger than that from gaseous CO2. The increase in compressive strength was the largest when using recycled fine aggregate reacted with scCO2. It was clear that quality improvement of recycled fine aggregate was higher with scCO2 than with gaseous CO2.

• Journal of the Korean Chemical Society
• /
• v.45 no.2
• /
• pp.149-155
• /
• 2001

A new analytical method of cyanobacterial toxins, i, e, microcysins was deveeloped using supercritical fluid extraction(SFE). The microcystins mcluded in the study are sparsely soluble in neat supercritical fluid CO$_2$ However, the microcystins were successfully extracted with a temary mixture(90% CO$_2$,9.0% methanol 1.0% water) at 40$^{\circ}$C and 250 atm. The SFE method developed in this study has several advantages over solid-phase extraction(SPE) sample preparation for the analysis of microcystins. Sample handling steps are minimized thus reducing possible losses of analytes and saving analysis time. No clean-up steps are employed in this SFE method. Althouhgh many methods have been described for microcystim RR and LR, the method using solid-phase extraction with ODS cartridges is the most commonly used. However, the adsorbing power of ODS caridges for microcystins is weak, so we have attempted to use a more polar CN cartridge, to increase the adsorbing power for microcystins. Lyophilized cells(100mg) were wxtracted with 5% (v/v) acetic acid. The extract was centrifuged and then the supernatant was applied to a CN cartridge. The cartridge which contained microcystins was rinsed with 5 ml of water and 5 ml of 0.5 M acetic acid. followed by 5 ml of 5% acetonitrile in water , and were determined by HPLC. Better recoveries and chromatogram were observed than with ODS cartridge.

• Clean Technology
• /
• v.24 no.4
• /
• pp.275-279
• /
• 2018

In this study, microemulsion formation of water and carbon dioxide was investigated by using surfactant as one of the methods for increasing the mutual solubility between water and carbon dioxide. The surfactant 2,2,3,3,3-Pentafluoro-1-propanol was added to form a microemulsion of water and carbon dioxide. The cloud point change and trend of micro emulsion were investigated by adding water and a certain amount of surfactant, 2,2,3,3,3-Pentafluoro-1-propanol to supercritical carbon dioxide. In the case of surfactant + carbon dioxide system, it was 8.35 ~ 12.69 MPa in temperature range of 313.2 ~ 353.2 K. In the case of water + surfactant + carbon dioxide system, the temperature ranged from 318.2 ~ 338.2 K to pressure range 7.83 ~ 17.28 MPa.

• Corrosion Science and Technology
• /
• v.15 no.3
• /
• pp.113-119
• /
• 2016

Corrosion science faces new challenges in various nuclear environments. Three main areas may be identified where increases of knowledge and understanding have been done and are still needed to face the technical needs: (i) the extension of the service time of nuclear power plants from 40 years, as initially planned, to 60 years and probably more as expected now, (ii) the prediction of long term behaviour of metallic materials in nuclear waste disposal where the corrosion processes have to be predicted over large periods of time, some thousands years and more, (iii) the choice of materials for use at very high temperatures as expected in Generation IV power plants in environments like gas (helium), supercritical water, liquid metals or salts. Service time extension, deep geological waste repositories and high temperature reactors sustain researches and developments to model corrosion phenomena at various scales, from atoms to components.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1692-1697
• /
• 2004

The once-through heat recovery steam generator is ideally matched to very high temperature and pressure, well into the supercritical range. Moreover this type of boiler is structurally simpler than drum type boiler. In drum type boiler, each tube play a well-defined role: water preheating, vaporization, superheating. Empirical equations are available to predict the average heat transfer coefficient for each regime. For once-through heat recovery steam generator, this is no more the case and mathematical models have to be adapted to account for the disappearance of drum type economizer, boiler, superheater. General equations have to be used for each tube of boiler, and actual heat transfer condition in each tube has to be identified.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05a
• /
• pp.15-20
• /
• 1997

We present the results HELIOS verification against VENUS PWR critical experiments loaded with high plutonium content mixed oxides fuels. The effective multiplication factors are calculated to be slightly supercritical within an acceptable error bound. In the prediction of power shape, HELIOS results are in close agreement with the measured values. The RMS errors of re-normalized calculated fission rate distribution are less than 1.4 % with either explicit or implicit models or micro tubes/rods in each fuel assembly for both ALL-MOX and GD-MOX mock-up cores.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.246-247
• /
• 2005

The paper presents the heat transfer characteristics during cooling process of carbon dioxide($CO_2$) in a helically coiled tube. The main components of the apparatus consist of a receiver, a variable speed pump, a mass flowmeter, a pre-heater, a gas cooler(test section) and an isothermal tank. The test section with the inner diameter 4.55 [mm] is a tube in tube type heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus. The main results were summarized as follows : The heat transfer coefficient increases with respect to the decrease of the gas cooler pressure in a supercritical region and the increase of the refrigerant mass flux. The pressure drop decreases in increases of the gas cooler pressure and increases with respect to increases the refrigerant mass flux.

• Nuclear Engineering and Technology
• /
• v.38 no.7
• /
• pp.591-618
• /
• 2006

An integrated R&D program is being conducted to study, qualify, and in some cases, develop materials with required properties for the reactor systems being developed as part the U.S. Department of Energy's Generation IV Reactor Program. The goal of the program is to ensure that the materials research and development (R&D) needed to support Gen IV applications will comprise a comprehensive and integrated effort to identify and provide the materials data and its interpretation needed for the design and construction of the selected advanced reactor concepts. The major materials issues for the five primary systems that have been considered within the U.S. Gen IV Reactor Program-very high temperature gas-cooled, supercritical water-cooled, gas-cooled fast spectrum, lead-cooled fast spectrum, and sodium-cooled fast spectrum reactors-are described along with the R&D that has been identified to address them.