• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.213-213
• /
• 2009

In this paper, we investigated the current limiting characteristics due to the application location of the superconducting fault current limiter (SFCL) such as the feeder, the bus, the secondary side of transformer in a power distribution system. In addition, the quench and the recovery characteristics of the SFCL installed in each location of the power distribution system were compared each other. Through the analysis, in case that the SFCL was applied into the feeder line, its current limiting and voltage-drop compensating characteristics were confirmed to be the more effective. On the other hand, the power burden of the SFCL was increased higher compared to the SFCL'S other application location.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.215-215
• /
• 2009

Improved flux-lock type superconducting fault current limiter(SFCL) is composed of a series transformer and superconducting unit of the YBCO coated conductor. The primary and secondary coils in the transformer were wound in series each other through an iron core and the YBCO coated conductor was connected with secondary coil in parallel. In this paper, we investigated the current limiting characteristics through initial line current after fault initiation. through the analysis, it was shown that the smaller initial line current is superior to current limiting characteristics and a point of view of power burden of the YBCO coated conductor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.327-330
• /
• 2001

Phase intergrowth in BSCCO thin films have been investigated. It turned out from XRD analyses of these phases that molar fraction of each constituent phase in the intergrowth thin film can be exhibited as a function of substrate temperature and ozone pressure. Superconducting behavior of the intergrowth thin film is also discussed.

• 한국전기전자재료학회논문지
• /
• 제18권4호
• /
• pp.370-374
• /
• 2005

AC loss of a superconducting conductor has a strong influence on the economic viability of a superconducting fault current limiter, which offers an attractive means to limit short circuit current in power systems. Therefore, the AC loss characteristics in several fault current limiting elements of a coil type have been investigated experimentally. The test result shows that AC losses measured in the fault current limiting elements depend on arrangement of a voltage lead. The AC loss of a bifilar coil is smallest among the fault current limiting elements of the coil type. The measured AC loss of the bifilar coil is much smaller than that calculated from Norris's elliptical model. However, the loss measured in a meander, which is frequently used in a resistive fault current limiter, agrees well to the theoretical one.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.222-224
• /
• 1997

This study is about a connective method of High Tc wire for long wire. We prepared silver-sheathed BiPbSrCaCuO wires by the powder-in-tube method. Since the superconducting wires are ceramic, it is very hard to connect each other. In this study, we used a silver sleeve to contract wires and pressed them by various preasures. Then optimum preasure was 9,000 Kgf/$\textrm{cm}^2$ to get the high critical current. The higest critical current was 10A.

• 한국전기전자재료학회논문지
• /
• 제18권10호
• /
• pp.956-959
• /
• 2005

High Tc superconducting with a BiSrCaCuO was prepared by the titrate method. The solid precursor produced by the dehydration of the gel at $120^{\circ}C$ for 12 h is not in the amorphous state as expected but in a crystalline state. X-tay diffraction peaks of nearly the same angular position as the peaks of high Tc phase were observed in the precursor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.148-151
• /
• 1995

Excimer laser has been used to fabricate superconducting YBa$_2$Cu$_3$O$\sub$7-x/(YBCO) thin films on various substrates. An XeCl excimer laser with an wavelength of 308 nm was used to deposit both buffer layer and superconducting thin film on sapphire substrate. The characterizations of the interface between thin film and substrate were performed. The interfacial properties of thin films on buffered sapphire and on bare sapphire were compared. With a 20 nm PrBa$_2$Cu$_3$O$\sub$7-x/(PBCO) buffer layer, no diffusion layer was observed between film and substrate while the diffusion layer with about 30 nm thickness was observed between film and sapphire without buffer layer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.259-260
• /
• 2006

$Bi_2Sr_2Ca_{n-1}Cu_nO_x$ superconducting thin films have been fabricated by atomic layer-by-layer deposition using IBS(Ion Beam Sputtering) method During the deposition, 90 mol% ozone gas of typical pressure of $1{\sim}9{\times}10^{-5}$ T orr are supplied with ultraviolet light irradiation for oxidation. XRD and RHEED investigations reveal out that a buffer layer with some different compositions is formed at the early deposition stage of less than 10 units cell and then Bi-2201 oriented along the c-axis is grown.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.196-199
• /
• 1999

The coexistence of the superconductivity and magnetism in the Ho1-xDyxNi2B2C is studied by using Ginzburg-Landau theory. This material violates the standard do Gennes scaling showing the coexistence and complex interplay of superconducting and magnetic order yielding an anomalous phase diagram. We propose a phenomenological model which includes two magnetic and two superconducting order parameters accounting for the multi-band structure of this material. We describe the magnetic fluctuations and order and demonstrate that they lead to anomalous behavior of the upper critical field. The doping dependence of Tc in Ho1-xDyxNi2B2C showing a reentrance behavior are analyzed yielding a very good agreement with experimental data.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.427-430
• /
• 1999

This paper presents a S-FES(Superconducting magnetic bearing Flywheel Energy Storage System) for the purpose of replacing battery used to store the energy. Especially, the design elements of FES, such as the bearing, wheel material, and power converter, etc., is described. The design and manufacturing techniques of the controllable power converter are proposed to generate the sinusoidal output current in the high speed operation and to get the constant DC voltage in the regeneration mode. The cylindrical permanent magnet synchronous motor with halbach array of Nd-Fe-B permanent magnet which is the high coercivity material is used as the driver of FES. The proposed S-FES system shows the stable rotation characteristics at high speed range about 10,000 rpm. To verify the validity of proposed system, the comparative study with the conventional ball bearing system is proceeded and it is well confirmed with the result of the lower friction loss of S-FES system.