• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1130-1132
• /
• 2004

In this paper, we investigated the operational characteristics of the fault current limiting in the The flux-lock type high-Tc superconducting fault current limiter. The flux-lock type high-Tc superconducting fault current limiter was consisted of primary and secondary copper coils that flux was locked on iron core and YBCO thin film. The operational characteristic of a flux-lock type SFCL dependent on winding direction of coil 1 and coil 2, and the number of turns of coil 1 and coil 2, inductances of the coils, saturation in iron core, the properties of superconducting element etc. In this cases, we investigated the fault currents limiting characteristics of the flux-lock type SFCL when winding direction of coil 1 and coil 2 was subtractive polarity winding.

• 한국초전도학회:학술대회논문집
• /
• v.14
• /
• pp.73-73
• /
• 2004

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.4
• /
• pp.11-14
• /
• 2001

Phase intergrowth in BSCCO thin films has been Investigated. It turfed out from XRD analyses of these phases that molar fraction of each constituent phase in the intergrowth thin film can be exhibited as a function of substrate temperature and ozone pressure. Super- conducting behavior of the intergrowth thin aim Is also discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05b
• /
• pp.12-15
• /
• 2003

The YBaCuO thick film was deposited by the electrophoresis in the solution with different dimension particles. The morphology of the films deposited from different particles size was compared. The powder made by sol-gel method has the submicron particles, which deposit the most smooth film, and without microcracks after sintering. After sintering of the deposited film, the zone-melting process was carried out in low oxygen partial pressure (100 Pa) and Ag was used as substrate. And the zone-melted YBaCuO was studied by XRD.

• Journal of information and communication convergence engineering
• /
• v.1 no.2
• /
• pp.63-66
• /
• 2003

High $T_c$ superconducting lines will be applied as key materials in the areas of power transmission line; magnetic levitation of vehicle; magnetic separation; magnetic energy storage and marine propulsion. A combination method of electrophoresis deposition and zone-melting for preparation of YBaCuO tape is proposed. The submicron particle powder of YBaCuO made by sol-gel method is used in the electrophoresis process. A 40∼50 ${\mu}\textrm{m}$ thickness of YBaCuO film on Ag plate could be deposited in about three minutes. After deposition the film is rolled and heat treated in order to increase the density and the adhesion of the film to the Ag plate. Silver(Ag) and lead oxide(PbO) were added in the YBaCuO powder in order to reduce its melting point. The YBaCuO coating with controlled Ag and PbO contents was preliminarily zone-melted at about $945^{\circ}C$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.11a
• /
• pp.5-6
• /
• 1993

• 한국초전도학회:학술대회논문집
• /
• 2009.07a
• /
• pp.29-29
• /
• 2009

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.02a
• /
• pp.153-153
• /
• 2008

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.589-594
• /
• 1997

Superconducting $YBa_2Cu_3O_y$ thin films were prepared at the deposition temperature of $650^{\circ}C$ under oxygen partial pressure of 0.0126 Torr on Si(111) and SrTiO3(100) substrates by chemical vapor deposition technique using $\beta$-diketonates of Y, Ba and Cu as source materials. The thin film fabricated on $SrTiO_3(100)$ had a $T_{c,onset}$ of 91K and $T_{c.0}$ of 87K. The thin film prepared on Si(111) had a $T_{c,onset}$ of 91K but didn't have a $T_{c.0}$ at liquid nitrogen boiling point(77.3K). Dense and two-dimensionally well alligned microstructure was developed for the film deposited on $SrTiO_3(100)$ substrate whereas a relatively porous and randomly distributed microstructure was developed for the film prepared on Si(111) substrate.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.87-92
• /
• 2006

The effects of Ba and Ce addition has been investigated in YBCO prepared by trifluoroacetate(TFA) metalorganic depostition(MOD) method. Precursor solutions with cation ratios of Y:Ba:Cu:Ce=1:2+x:3:x(x=0, 0.05, 0.1 and 1.5) have been prepared by adding an excess amount of cerium and barium. Coated film was calcined at lower temperature under a moisture-containing oxygen atmosphere. Superconducting YBCO films have been obtained by performing conversion heat treatment at temperature of $780{\sim}810^{\circ}C$ under a moisture-containing Ar(1,000 ppm oxygen) atmosphere. It has been shown that the critical current($I_c$) of YBCO film was degraded by doping of Ba and Ce atoms. But $I_c$ was increased as the amount of doped Ba and Ce content increased from 5% to 15 %. It was observed that there was little increase of a flux pinning force with Ba and Ce addition in YBCO film prepared by TFA-MOD process.