통상 제어기 설계용으로 개발되는 차량용 수퍼 차져의 동적 거동 모델은 경험식에 의존한 압축기 맵을 활용하고 있어, 실제 서지 현상의 발생에 따른 시스템의 영향과 거동특성을 모사하는데 한계가 있다. 본 연구에서는 수퍼 차져의 운전 동특성을 모사할 수 있는 해석기반 압축기 모델을 개발하고 운전 변동성에 따른 압축기의 운전 추이를 모사하고자 한다. 모델 개발은 SIMULINK$^{(R)}$ 환경에서 진행하고, 기준 동특성 모델은 Greitzer의 압축기 모델을 적용하였다. 해석 결과는 실험 결과와 비교 검증을 통해 모델의 타당성을 확인하였으며 운전 특성 변화에 따른 압축기 성능 및 서지 발생 가능성에 대해 확인 하였다.
A ground source heat pump system maintains a constant efficiency due to its stable heat source and radiant heat temperature which provide a more effective thermal performance than that of the air source heat pump system. As an eco-friendly renewable energy source, it can reduce electric power and carbon dioxide. In this study, we analyzed one year of data from a web based remote monitoring system to estimate the thermal performance of GSHP with the capacity of 3RT, which is installed in a low energy house located in Daejeon, Korea. This GSHP system is a hybrid system connected to a solar hot water system. Cold and hot water stored in a buffer tank is supplied to six ceiling cassette type fan coil units and a floor panel heating system installed in each room. The results are as follows. First, the GSHP system was operated for ten minutes intermittently in summer in order to decrease the heat load caused by super-insulation. Second, the energy consumption in winter where the system was operated throughout the entire day was 7.5 times higher than that in summer. Moreover, the annual COP of the heating and cooling system was 4.1 in summer and 4.2 in winter, showing little difference. Third, the outlet temperature of the ground heat exchanger in winter decreased from $13^{\circ}C$ in November to $9^{\circ}C$ in February, while that in summer increased from $14^{\circ}C$ to $17^{\circ}C$ showing that the temperature change in winter is greater than that in summer.
장어통발의 P.P깔때기 살과 대나무 깔때기 살의 탄성을 측정하고 측면 구멍을 막은 통발과 원형의 유수저항, 침강시간 및 미끼의 냄새확산 등을 관찰한 다음 해상어획 시험을 행한 결과는 다음과 같다. 1. P.P 깔때기 살의 탄성은 대나무 살보다 훨씬 작고, 하중이 증가할수록 탄성회복도는 감소하였다. 2. 플라스틱 장어통발의 유수저항 R(kg)는 유속 V(m/sec)에 따라 다음 관계식으로 나타낼 수 있다. R=0.36V 상(2.01) 3. 장어통발의 침강시간은 측면 구멍을 막은 경우 수면상에서의 완전 침수까지 1~2초 정도 원형보다 지연되나 그 후의 침강속도는 거의 차이가 없었다. 4. 통발 내의 미끼 수용액은 측면 구멍을 많이 막을수록 원형보다 입구쪽으로 집중되어 확산되었다. 5. 측면 구멍을 일부 막은 통발과 원형을 가지고 어획시험을 한 결과 통발당 평균 어획미수나 평균어획량의 어획성능에 있어서 뻘로 된 어장에서는 차이가 없는 것 같다.
Objectives: To estimate the microbial contaminant load discharged from livestock farms, we randomly selected livestock farmers of cattle, swine, and fowl and collected bacterial strains from domestic animals' feces and compost samples. Recently, as multi-antibiotic-resistant bacteria and super bacteria showing resistance to a variety of antibiotics have been reported one after another, the ecological and health hazard of antibiotic-resistant bacteria is emerging as an important issue. Methods: Monitored indicator microorganism constituents were totak coliform (TC), fecal coliform (FC), and aerobic bacteria. The multi-antibiotic-resistant bacteria were identified from investigated indicator microorganisms by 16S rRNA sequencing. Results: By microbiological analysis, the largest population of aerobic bacteria ($1.5{\times}10^5$ CFU/g) was found in cattle fecal compost, and total coliforms ($1.1{\times}10^7$ CFU/g) and fecal coliforms ($1.0{\times}10^5$ CFU/g) were found primarily in swine fecal compost, while the lowest population was found in fowl fecal compost. Among the 67 strains separated from aerobic bacteria, five strains expressing high antibiotic resistance were selected in each sample. We found the multi-antibiotic resistant strains to be Shigella boydii, Staphylococcus lentus, Acinetobacter sp. and Brevibacterium luteolum. Conclusions: These results suggest that increasing numbers of multi-antibiotic-resistant bacteria in the environment have a close relation to the reckless use of antibiotics with livestock.
Fuel cell power system is one of the most promising energy source for the alternative energy because it has unique advantages such as high energy density, no power drop during operation, and feasible to make compact size. However, due to very low response time, fuel cell is difficult to correspond to drastic load changes and start-up operation. For solving these problem, fuel cell power system must include energy storage device such as Li-Poly battery or super capacitor. Therefore, bi-directional DC-DC converter must be required for this storage device and fuel cell-PCS control. This paper presents a design and modeling of the bi-directional DC/DC converter. Firstly, we present modeling the boost and buck mode of the bi-directional converter through both PWM switch model and state space averaging technique. Secondly, in order to minimize output ripple and transient response overshoot, we have two identical DC-DC converters interleaved and adopt two-loop voltage-current controller. The proposed bi-directional DC-DC converter's modeling method and control design have been verified with computer simulation and experimentation.
최근 초고층 빌딩의 구조설계에 있어서 풍하중이 가장 중요한 하중요소로 다루어지고 있으며, 일반적으로 풍하중 산정은 풍동실험에 의하여 수행되어 왔다. 그러나 보다 간편하면서도 정밀한 산정방법의 개발에 대한 필요성이 증대되면서 그 방법의 하나로 수치해석적인 접근법인 전산유체역학이 이용되고 있다. 또한 CFD해석은 실제 스케일로 모델링 및 시뮬레이션이 가능하고 시간도 단축할 수 있는 장점을 가지고 있다. 그럼에도 불구하고 실제 프로젝트에 대한 연구의 역사와 검증과정이 일천하여 이 해석법에 의한 신뢰도가 낮기 때문에 그 활용은 미미한 실정이다. 따라서 본 연구에서는 기존연구에서 제시된 프로토타입 모델의 풍동실험 결과와 CFD해석을 통한 해석 결과의 비교를 통해 CFD해석의 신뢰도를 입증하며, 더불어 난류강도가 신뢰도에 미치는 영향에 대해 제시하고자 한다.
KSII Transactions on Internet and Information Systems (TIIS)
/
제6권9호
/
pp.2285-2301
/
2012
Peer-to-Peer (P2P) networks are becoming more and more popular in video content delivery services, such as Video on Demand (VoD). Scalability feature of P2P allows a higher number of simultaneous users at a given server load and bandwidth to use stream service. However, the quality of service (QoS) in these networks is difficult to be guaranteed because of the free-riding problem that nodes download the recourses while never uploading recourses, which degrades the performance of P2P VoD networks. In this paper, a distributed trust model is designed to reduce node's free-riding phenomenon in P2P VoD networks. In this model, the P2P network is abstracted to be a super node hierarchical structure to monitor the reputation of nodes. In order to calculate the reputation of nodes, the Hidden Markov Model (HMM) is introduced in this paper. Besides, a distinction algorithm is proposed to distinguish the free-riders and malicious nodes. The free-riders are the nodes which have a low frequency to free-ride. And the malicious nodes have a high frequency to free-ride. The distinction algorithm takes different measures to response to the request of these two kinds of free-riders. The simulation results demonstrate that this proposed trust model can improve QoS effectively in P2P VoD networks.
최근의 오디오 압축 알고리듬은 다양한 코딩 기법을 조합하여 사용하고 있다. 이들은 DSP 작업(DSP task), 제어 작업(controller task), 그리고 혼합 작업(mixed task)으로 나눌 수 있다. 기존의 DSP 프로세서들은 이들 중 DSP 작업만을 효율적으로 설계되어 있어 제어작업이나 혼합작업에 대해서는 자원을 효율적으로 활용하지 못하는 단점이 있다. 본 논문에서는 기존의 DSP 프로세서가 가지는 DSP 작업에 대하여 고성능을 그대로 유지하면서 제어작업과 혼합작업에서도 좋은 성능을 가지는 새로운 구조를 제안하고 구현하였다. 제안된 프로세서 YSP-3는 4개의 실행 유닛 (곱셈기, 2개의 ALU, 메모리 접근 유닛)을 병렬로 배치한 후 4-way 수퍼스칼라명령어 구조를 사용하여 각 우ㅠ닛을 독립적으로 사용할 수 있도록 하였다. 제안된 구조는 일반적인 DSP 알고리듬과 AC-3 디코딩 알고리듬을 실행하여 성능을 평가하였다. 마지막으로 VHDL을 통해 $0.6\$\mu$textrm{m}$-3ML 표준셀 기술로 합성한 후 Compass상에서 모의실험으로 통해 33MHz의 시스템 클럭에 대해 최대 지연시간 상황에서 실시간 동작을 확인하였다.
Use of the PV(photovoltaic) generation system is increased in such areas as remote mountain places or islands at which electrical energy is not serviced. The stand alone PV system is required the power storage products such as battery, fly wheel and super capacitor. Several lead storage batteries are connected in series to get high voltages. The life of lead storage battery is shortened when over charge or over discharge takes place. So, it is needed to control batteries not to be overcharged or be discharged deeply. Voltage of each battery was ignored in former control methods in which overall voltage was used to control charge or discharge battery. In this study, the charging and discharging voltage variations of sealed lead storage batteries with l2V/l.2A were investigated step by step experiments. The results of the test show that one should consider and specify the state of each battery to prevent overcharge or deep discharge. With the basis of the experiments, we designed a monitoring unit to monitor battery voltages simultaneously using micro-controller. The unit measures voltage of 20 batteries simultaneously and displays data on the color LCD monitor with curved line graph. It also sends data to PC using the RS232C communication port. The designed unit was adapted to stand alone PV system with 1kW capacity and lead storage batteries are connected to the PV generation system. The number of lead storage batteries was 10 in series and 12V/250Ah each. Resistive load with 3kW was used for discharging.
Due to the need of increasing thermal efficiency, supercritical pressure and temperature have been utilized in power plants. It is well known that 9Cr1Mo steel is suitable fer use in power plants operating at supercritical conditions. Therefore, to ensure the safety and the soundness of the power plant, creep characterization of the steel is important. In this study, the creep characterization of the gCr1Mo steel using small punch creep(SP-Creep) test has been described. The applied load and the central displacement of the specimen in SP-Creep test have been converted to bearing stress and strain of uc, respectively. The converted SP-Creep curves clearly showed the typical three-stage behavior of creep. The steady-state creep rate and the rupture time of the steel logarithmically changed with the bearing stress and satisfied the Power law relationship. Furthermore, the Larson-Miller parameter of the SP-Creep test agreed with that of the tensile creep test. From the comparison with low Cr-Mo steels, the creep characteristics of 9Cr1Mo steel proved to be superior. Thus, it can be confirmed that the 9Cr1Mo steel is suitable for supercritical power plant.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.