• Journal of Korean Society of Forest Science
• /
• v.35 no.1
• /
• pp.19-23
• /
• 1977

Tropical hard wood produces a number of extracts, especially hot-water extracts. The lignin content in the two kinds of bangkirai and red lauan belonging to genus Shorea, was as high as in temperate zone soft wood, mangrove wood of genus Rhizophara contained it on the same level as temperate zone hard wood and keruing of genus Dipterocarpus was in between the two kinds of bangkirau and red lauan, and keruing wood. The xylose content of saccharose composition in the tree of genus Shorea, was as low as in needle-leaved trees, mangrove wood contained it on the same level as broad-leaved trees and the xylose content in keruing wood was in between the above two kinds of wood. The total retrieving rate of alditol acetate acetificated with sulphuric acid and acetic anhydride, did not reach 100%, even if it was supplemented. There was no difficulty in analyzing alditol immediately after acetification but, when it was left for four or five days, the acetificated alditol acetate was dissolved. The pyridine alditol acetificated with pyridine and acetic anhydride, showed the same result.

• Journal of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.1-9
• /
• 1962

Bench-scale horizontal cation-permeable membrane cells were constructed to study the effect of cell dimensions on the efficiency of electrolytic reduction of uranyl sulphate solutions flowing continuously over a mercury cathode. Current efficiencies were determined for various cells having length-to-width ratios of 10/1 to 40/1, and for catholyte solutions containing from 20 to 100g $U_3O_8/l$ in sulphuric acid. Optimum current density and solution flowrate were determined under these conditions. The effects of the nitrate and chloride ions were briefly examined.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.247-252
• /
• 2009

The LMC method of construction which have application to the road bridge is being considered the least relative importance about the watertight performance, because it focused on the durability of concrete. However, The LMC which is being expanded scope of application to the method of construction has grown importance about the watertight performance on the usability and maintenance side as well as durability. In this study, The latex concrete of two types which are different from mingled-ratio of the latex made a comparison to the compressive strength, watertight performance, dynamic wheel load resistance performance and confirmed what it has resistibility about chemical action through the chemical resistance test. The initial strength and watertight performance showed that were tendency the downward at 14 days. However, The long-term strength after 28 days showed that it has firm performance. In consequence, The initial curing of latex concrete is required to scrupulous care and attention at the site application. As a chemical resistance test result, The specimen that is steeped in sulphuric acid solution of 2% discovered the delamination phenomenon. However, it was confirmed that delamination phenomenon don't have an effect on the compressive strength. Moreover, As a dynamic wheel load resistance test result, The latex concrete was concluded to confirming the durability and running stability, because it had hardly any thickness reduction of latex concrete surface about dynamic wheel load and rarely found crack and delamination.

• Economic and Environmental Geology
• /
• v.8 no.4
• /
• pp.183-201
• /
• 1975

The south and southwestern parts of Jeonra-namdo has been known as an alunite province in Korea. The alunite deposits investigated for the present study are Okmaisan, Seongsam, Bugog, Gasado south, Gasado north, Jangsando, Dogcheon and Jungyongri deposits. The main purpose of this study is to depict the genetical origin of the alunite deposits. The rocks distributed in the areas mentioned above consist chiefly of rhyolitic tuff, breccia tuff and andesitic tuff of Cretaceous age which represent different episodes of volcanic activities during Cretaceous epoch. The attitude of bedding of the tuffaceous rocks varies from place to place but generally dips very gently. The alunite deposits are embedded mostly in the rhyolitic tuff so that they appear as layered deposits, this occurrence may be the result of stratigraphic and lithologic controls. The result of this study can be summarized as below. The mineral sequence studied by the mineral paragenesis and the result of the spectrograph anlyses is such that (1) alunite was formed at first and pyrophyllite was nearly contemporaneous with alunite but pyrophyllite formation can be recognized as a secondary mineralization products, (2) kaoline was succeeded to form later and hematite finally deposited, and (3) pyrite was deposited from the begining to the end of the above mineralization period. The compositional change of host rocks is such that CaO, $SiO_2$ and $Na_2O$ were largely removed from the parent rocks and some $Al_2O_3$ and $SO_3$ were transported by the solution so as to enrich the rocks. The sequencial process of such mineralization has resulted in forming those distinguish mineral zones; alunite, kaoline, pyrophyllite, silicifide and sulphide zone which manifest irregular shape. These deposits were formed by hydrothermal solution which was possibly low temperature and contained sulphuric acid originated from $H_2S$ and $SO_2$ gases.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.05a
• /
• pp.78-85
• /
• 2006

In textile industries, waste effluent containing zinc is generated during the manufacture of rayon yarn from the wood pulp or cotton linters. Due to the strict environmental regulations and the presence of toxic metallic and other constituents, the discharge of industrial effluents in the sewage or disposal of solid sludge as landfill is restricted. Before recycling of zinc as zinc sulphate solution to the spinning-bath of the rayon manufacturing plant the zinc sulphate solution must be free from calcium, which is deleterious to the process as gypsum precipitates with the increase in concentration and forms scale in the bath. In the present work an attempt has been made to develop a process following solvent extraction technique using thiophosphinic extractants, Cyanex 272 and 302 modified with isodecanol and diluted in kerosene to recover zinc from rayon effluent. Various process parameters viz. extraction of zinc from different concentration of solution, distribution ratio, selective extraction, O/A ratio on extraction and stripping from the loaded organic, complex formation in the organic phase etc. have been studied to see the feasibility of the process. The extractant Cyanex 302 has been found selective for the recovery of 99.99% of zinc from the effluent above equilibrium pH 3.4 maintaining the O/A ratio of 1/30 leaving all the calcium in the raffinate. It selectively extracted zinc in the form of complex $[R_{2}Zn.3RH]_{org}$ and retained all the calcium in the aqueous raffinate. The zinc from the loaded Cyanex 302 can be stripped with 10% sulphuric acid at even O/A ratio of 10 without affecting the stripping efficiency. The stripped solution thus obtained could be recycled in the spinning bath of the rayon plant. The raffinate obtained after the recovery of zinc could be disposed safely without affacting environment.

• Nuclear Engineering and Technology
• /
• v.7 no.3
• /
• pp.213-222
• /
• 1975

Immobilization of the second-cycle radioactive liquid wastes from a Purex process was developed with the blown asphalt (manufactured by Kukdong Shell Oil Company Ltd) to eliminate the possibility that the radioactive materials will be redispersed into the environment. Attempts to incorporate these wastes directly into the asphalt martrices without any pretreatment were not successful, as it was observed that the sulphuric acid in the waste oxidised the asphalt. Hence, the waste was treated with caustic soda and made alkaline prior to bituminization, so that it was found that this pretreatment made the waste compatible to the asphalt matrices. The pure blown asphalt samples irradiated with doses of 4.0$\times$10$^{7}$ rad showed no evidence of volume increase. The suitable temperature for incorporation of the alkaline wastes into blown asphalt was 180-20$0^{\circ}C$. The Products containing 50 wt% salts represented the following good properties viz., volume reduction (about 1.4), homogeneity, teachability etc. During the period of 131 day $s^{l37}$Cs from products containing 40wt% salts was leached at rates ranging from 2.70$\times$10-4 to 8.27$\times$10-4g/cm2_day but the rate for $^{90}$ Sr was lower by one to two orders of magnitude by distilled water. The leaching rates for $^{137}$ Cs and $^{90}$ Sr by sea water were slightly lower than by distilled water. Both of the leaching rates decreased with increasing pH.H.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1273-1273
• /
• 2001

The efficiency of the luminal fermentation process influences overall efficiency of luminal production, animal health and reproduction. Ruminant production systems have a significant impact on the global environment, as well. Animal wastes contribute to pollution of the environment as ammonia volatilized to the air and nitrate leached to ground water. Microbial protein synthesis in the rumen satisfies a large proportion of the protein requirements of animals. Quantifying the microbial synthesis is possible by using markers for lumen bacteria and protozoa such as nucleic acids, purine bases, some specific amino acids, or by isotopic $^{15}N,^{32}P,\;and\;^{35}S$ labelled feeds. All those methods require cannulated animals, they are time-consuming and some methods are very expensive as well. Many attempts have been made to find an alternative method for indirect measurement of microbial synthesis in intact animals. The present investigations aimed to assess possibilities of NIRS for prediction of purine nitrogen excretion and ruminal microbial nitrogen synthesis by NIR spectra of urine. Urine samples were collected from 12 growing sheep,6 of them male, and 6- female. The sheep were included in feeding experiment. The ration consisted of sorghum silage and protein supplements -70:30 on dry matter basis. The protein supplements were chosen to differ in protein degradability. The urine samples were collected daily in a vessel containing $60m{\ell}$ 10% sulphuric acid to reduce pH below 3 and diluted with tap water to 4 liters. Samples were stored in plastic bottles and frozen at $-20^{\circ}C$ until chemical and NIRS analysis. The urine samples were analyzed for purine derivates - allantoin, uric acid, xantine and hypoxantine content. Microbial nitrogen synthesis in the lumen was calculated according to Chen and Gomes, 1995. Transmittance urine spectra with sample thickness 1mm were obtained by NIR System 6500 spectrophotometer in the spectral range 1100-2500nm. The calibration was performed using ISI software and PLS regression, respectively. The following statistical results of NIRS calibration for prediction of purine derivatives and microbial protein synthesis were obtained.(Table Omitted). The result of estimation of purine nitrogen excretion and microbial protein synthesis by NIR spectra of urine showed accuracy, adequate for rapid evaluation of microbial protein synthesis for a large number of animals and different diets. The results indicate that the advantages of the NIRS technology can be extended into animal physiological studies. The fast and low cost NIRS analyses could be used with no significant loss of accuracy when microbial protein synthesis in the lumen and the microbial protein flow in the duodenum are to be assessed by NIRS.

• Resources Recycling
• /
• v.17 no.2
• /
• pp.3-15
• /
• 2008

Different toxic wastes are disposed of in our surroundings and these will ultimately threaten the existence of living organisms. Biohydrometallurgy, which includes the processes of bioleaching and bioremediation through the activities of microorganisms such as bacterial or fungal species, is a technology that has the potential to overcome many environmental problems at a reasonable economic cost. Bioleaching were carried out for dissolution of metals from different materials using most important metal mobilizing bacteria such as Thiobacillus ferrooxidans, Thiobacillus thiooxidans and Laptospirillum ferrooxidans. According to the reaction, bioleaching is parted as direct and indirect mechanism. In direct mechanism the bacteria oxidize the sulphides minerals by accepting electron and producing sulphuric acid in leaching media for their growth and metabolism. In other hand the indirect bioleaching is demonstrated as the oxidation of sulphides mineral by the oxidant like $Fe^{3+}$ produced by the iron oxidizing bacteria. Through this process, substantial amount of metal can be recovered from low-grade ores, concentrates, industrial wastes like sludge, tailings, fly ash, slag, electronic scrap, spent batteries and spent catalysts. This may be alternative technology to solve the high deposition of waste, which moves toward a healthy environment and green world.

• Resources Recycling
• /
• v.17 no.4
• /
• pp.37-46
• /
• 2008

In view of the increasing importance of the waste recycling to meet the strict environmental regulations, the present investigation reports an adsorption process using cationic exchanger DOWEX G-26 for the recovery of copper from the synthetic sulphate solutions containing copper 0.3 to 0.5 mg/ml, similar to the CMP waste effluent of electronic industry. Various process parameters viz. contact time, solution pH, resin dose, and A/R ratio for elution were investigated to recover copper from the effluents. Complete adsorption of copper from the solution was achieved at equilibrium pH 2.5 and aqueous I resin (A/R) ratio of 100 ml/g in 14 minutes contact time. The adsorption of copper on DOWEX G-26 resin was found to follow the Langmuir isotherm and second order reaction. The copper was eluted from loaded resin with dilute sulphuric acid to produce copper-enriched solution.

• CELLMED
• /
• v.11 no.3
• /
• pp.13.1-13.9
• /
• 2021

Background and Objective: Nux-vomica based traditional Unani formulation, Habb-e-Azaraqi (HAZ) is an important drug used by Unani physicians since several decades. It possesses Muqawwi-i-A'sab (nervine tonic), Muharrik-i-A'sab (nervine stimulant) properties and is an effective treatment option for diseases like Laqwa (facial palsy), Falij (paralysis), Niqris (gout) and Waja'al-Mafasil (arthritis) etc. The aim of the study is to access and provide information of HAZ for its TLC, HPTLC Fingerprinting defining its clear qualitative perspective and acute oral toxicity evaluation for its safety assessment which was not done earlier, thus contributing in the field of research. Materials and Methods: The chief ingredient, nux-vomica was detoxified as per method mentioned in Unani Pharmacopeia before its use in formulation. TLC and HPTLC was developed under four detection system i.e., UV 366nm, UV 254nm, exposure to iodine vapours and after derivatization with anisaldehyde sulphuric acid. Acute toxicity studies were performed as per OECD Guidelines 425 at a limit dose of 2000 mg/kg. Observations were done for signs of toxicity, body weight, and feed consumption at regular intervals followed by haematological and biochemistry evaluation. Results: The generated data proved the authenticity and established the TLC and HPTLC profile of the formulation. Acute toxicity revealed no significant differences in HAZ-treated animals with respect to body weight gain, feed consumption, haematology, clinical biochemistry evaluation. No significant gross pathological observation was noticed in necropsy. Conclusion: Data of the present study is substantial and scientific proof of HAZ in terms of standardization and toxicity study that can be utilize in future research activities.