• Journal of the Korean Vacuum Society
• /
• v.13 no.4
• /
• pp.157-163
• /
• 2004

Dependence of residual compressive stress of diamond-like carbon (DLC) films on relative humidity was investigated. Polymeric, graphitic and diamond-like carbon films were prepared by r.f.-PACVD using methane or benzene with the negative self bias voltage of the substrate ranging from -100 to -800 V. In-situ measurements of the residual stress were carried out in an environment chamber where the relative humidity was varied from 10％ to 90％. In dense DLC film of high residual compressive stress and hardness, we could not observe any change in the residual compressive stress with relative humidity. However, in the cases of graphitic and polymeric DLC films, abrupt change in the residual stress occurred by changing the relative humidity. The quantity of the stress change was inversely proportional to the film thickness, which means that the stress change with humidity is not due to the penetration of the water molecule into the film structure, but due to surface interaction between water molecules and film surface.

• Journal of the Korean Vacuum Society
• /
• v.8 no.1
• /
• pp.75-82
• /
• 1999

Ion energy is one of the crucial property in thin film deposition by internal ICP assisted I-PVD. As ion energy is determined by the difference between the plasma potential and the substrate bias potential, ICP excitation frequency was tested with medium frequency of 4 MHz and two types of tuning circuits, alternate and floating LC network with a biasing resistor, were tested. The results showed that plasma potential was less than 5 V in a range of Ar pressures, 5mTorr to 30 mTorr, at 4 MHz RF 600 W and 60 V of maximum RF antenna voltage was maintained either at RF input or output terminal. By proper control of RLC circuit installed after after RF antenna, 50V of RF induced voltage on RF antenna was obtained at 500W input power. The total impedance of RF antenna and plasma was around 10$\Omega$, and minimum RF voltage was obtained with a condition of lowest reactance at most 0.05$\Omega$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.77-77
• /
• 2011

These days, a growing demand for memory device is filled up with the flash memory and the dynamic random access memory (DRAM). Although DRAM is a reasonable solution for current demand, the universal novel memory with high density, high speed and nonvolatility, needs to be developed. Among various new memories, the magnetic random access memory (MRAM) device is considered as one of good candidate memories because of excellent features including high density, high speed, low operating power and nonvolatility. The etching of MTJ stack which is composed of magnetic materials and insulator such as MgO is one of the vital process for MRAM. Recently, MgO has attracted great interest in the MTJ stack as tunneling barrier layer for its high tunneling magnetoresistance values. For the successful realization of high density MRAM, the etching process of MgO thin films should be investigated. Until now, there were some works devoted to the investigations on etch characteristics of MgO thin films. Initially, ion milling was applied to the etching of MgO thin films. However, ion milling has many disadvantages such as sidewall redeposition and etching damage. High density plasma etching containing the magnetically enhanced reactive ion etching and high density reactive ion etching have been employed for the improvement of etching process. In this work, inductively coupled plasma reactive ion etching (ICPRIE) system was adopted for the improvement of etching process using MgO thin films and etching gas mixes of $CH_4$/Ar and $CH_4$/$O_2$/Ar have been employed. The etch rates are measured by a surface profilometer and etch profiles are observed using field emission scanning emission microscopy (FESEM). The effects of gas concentration and etch parameters such as coil rf power, dc-bias voltage to substrate, and gas pressure on etch characteristics will be systematically explored.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.285-285
• /
• 2011

EUVL (Extreme Ultra Violet Lithography) is one of competitive lithographic technologies for sub-30nm fabrication of nano-scale Si devices that can possibly replace the conventional photolithography used to make today's microcircuits. Among the core EUVL technologies, mask fabrication is of considerable importance since the use of new reflective optics having a completely different configuration compared to those of conventional photolithography. Therefore new materials and new mask fabrication process are required for high performance EUVL mask fabrication. This study investigated the etching properties of SnO2 (Tin Oxide) as a new absorber material for EUVL binary mask. The EUVL mask structure used for etching is SnO2 (absorber layer) / Ru (capping / etch stop layer) / Mo-Si multilayer (reflective layer) / Si (substrate). Since the Ru etch stop layer should not be etched, infinitely high selectivity of SnO2 layer to Ru ESL is required. To obtain infinitely high etch selectivity and very low LER (line edge roughness) values, etch parameters of gas flow ratio, top electrode power, dc self - bias voltage (Vdc), and etch time were varied in inductively coupled Cl2/Ar plasmas. For certain process window, infinitely high etch selectivity of SnO2 to Ru ESL could be obtained by optimizing the process parameters. Etch characteristics were measured by on scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) analyses. Detailed mechanisms for ultra-high etch selectivity will be discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.211-211
• /
• 2012

The electrical loss of the photo-generated carriers is dominated by the recombination at the metal- semiconductor interface. In order to enhance the performance of the solar cells, many studies have been performed on the surface treatment with passivation layer like SiN, SiO2, Al2O3, and a-Si:H. In this work, Al2O3 thin films were investigated to reduce recombination at surface. The Al2O3 thin films have two advantages, such as good passivation properties and back surface field (BSF) effect at rear surface. It is usually deposited by atomic layer deposition (ALD) technique. However, ALD process is a very expensive process and it has rather low deposition rate. In this study, the ICP-assisted reactive magnetron sputtering method was used to deposit Al2O3 thin films. For optimization of the properties of the Al2O3 thin film, various fabrication conditions were controlled, such as ICP RF power, substrate bias voltage and deposition temperature, and argon to oxygen ratio. Chemical states and atomic concentration ratio were analyzed by x-ray photoelectron spectroscopy (XPS). In order to investigate the electrical properties, Al/(Al2O3 or SiO2,/Al2O3)/Si (MIS) devices were fabricated and characterized using the C-V measurement technique (HP 4284A). The detailed characteristics of the Al2O3 passivation thin films manufactured by ICP-assisted reactive magnetron sputtering technique will be shown and discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.386-386
• /
• 2011

탄소나노튜브는 큰 길이 대 직경 비와 뛰어난 전기적 특성으로 인해 차세대 전계 방출 소자로 주목 받고 있다. 실질적인 전계방출 디스플레이로의 응용을 위한 대면적 제작과 유리 기판 사용을 위해 이용되었던 페이스트(paste)법은 높은 전기장 하에서 장시간 전계방출시 탄소나노튜브 전계방출원과 페이스트(paste)간의 낮은 접착력 때문에 발생하는 탄소나노튜브의 탈루현상(omission)과 유기물질(organic paste)에서 발생하는 탈기체(out-gassing) 문제점이 있었다. 최근 이런 문제점을 개선하기 위해 유기물질(organic paste)를 대체하여 금속바인더(metal binder) 물질을 사용한 결과들이 보고되고 있다. 본 연구에서는 유리기판 위에 제작된 탄소나노튜브 전계방출원의 수명 향상을 위하여 금속바인더와 후속 열처리법의 변화에 따른 전계방출 안정성을 분석하였다. 금속바인더는 접합층/ 접착층(soldering layer/ adhesive layer)으로 구성되어 있으며, 일반적인 소다석회유리(soda-lime glass)에 스퍼터(DC magnetron sputtering system)를 이용하여 증착하였다. 접착층은 유리기판과 접합층의 접착력 향상을 위해 사용되며, 접합층은 기판과 탄소나노튜브 전계방출원을 접합하는 역할과 전계방출 측정시 전극이 되기 때문에 우수한 전기 전도성과 내산화성을 필요로 한다. 본 실험에서는 일반적으로 유리기판과 접착력이 좋다고 알려진 Cr, Ti, Ni, Mo을 접착층으로 사용하였으며, 접합성과 전기전도성, 내산화성이 뛰어난 귀금속 계열의 금속을 접합층으로 사용하였다. 탄소나노튜브를 1,2-디클로로에탄(1,2-dichloroethane, DCE)에 분산시킨 용액을 스프레이방법을 이용하여 증착시켰으며, 후속 열처리 방법을 통하여 접합층과 결합시켰다. 금속바인더와 후속 열처리법의 변화에 따른 접착력과 표면형상(morphology)의 변화를 주사전자현미경(scanning electron microscopy)를 이용하여 분석하였으며, 다이오드 타입에 디씨 바이어스(DC bias)를 사용하여 전계방출특성을 측정하였다[1,2].

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.450-455
• /
• 2000

For further scaling down of the silicon devices, the application of low dielectric constant materials instead of silicon oxide has been considered to reduce power consumption, crosstalk, and interconnection delay. In this paper, the effect of $O_2/SF_6$ plasma chemistry on the etching characteristics of polyimide-one of the promising low-k interlayer dielectrics-has been studied. The etch rate of polyimide decreases with the addition of $SF_6$ gas due to formation of nonvolatile fluorine compounds inhibiting reaction between oxygen and hydrocarbon polymer, while applying substrate bias enhances etching process through physical attack. However, addition of small amount of $SF_6$ is desirable for etching topography. $SiO_2$ hard mask for polyimide etching is effective under $O_2$plasma etching(selectivity~30), while $O_2/SF_6$ chemistry degrades etching selectivity down to 4. Based on the above results, $1-2\mu\textrm{m}$ L&S PI2610 patterns were successfully etched.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.126-126
• /
• 2018

최근 차세대 디스플레이인 flexible 하고 transparent 한 디스플레이 개발이 진행 중 이며, 이러한 디스플레이가 개발 되기 위해 백 플레인으로 사용되는 Thin Film Transistor (TFT) 또한 차세대 디스플레이 못지 않게 연구가 진행 되고 있다. 기존의 무기물을 기반으로 하고 Rigid한 TFT는 현재 많은 곳에 적용이 되어 사람들이 사용 하고 있다. 하지만 이미 시장은 포화상태이며 차세대 디스플레이 컨셉인 flexible 하고 투명한 것과 맞지 않는다. 그래서 유연하며 투명한 특성을 가진 TFT에 대한 연구가 활발히 진행 되고 있으며 많은 성과를 이루었다. 이러한 소자를 이용하여 훗날 Electronic-skin(e-skin)이라 부르는 전자 피부를 활용하여 실시간 모니터링 할 수 있는 헬스 케어 분야 등에 활용 가치 또한 높다. 현재 유연하며 투명한 기판 및 물질 개발에 많은 연구 개발이 진행 되고 있다. 하지만 유연한 기판을 사용하여 TFT를 제작한 후 stress나 bending에 대한 내구성과 안정성, 신뢰성 등이 무기물을 기반으로 한 TFT에 비해 좋지 않은 실정이다. 따라서 유연하며 투명한 기판을 사용한 TFT에 대한 안정성, 신뢰성 등을 확보하여야 한다. 본 연구 에서는 유연한 기판을 사용하여 TFT를 제작 한 후, TFT특성과 안정성을 확보하는 것을 목표로 실험을 진행하였다. 우리는 Mo전극과 Parylene 기판을 사용하여 유연한 TFT소자를 탑 게이트 구조로 제작 하였고 Rigid한 Glass기판 위에 Floating Process를 진행하기 위해 PVA층을 코팅 후 그 위에 Parylene을 CVD로 증착 하고 IGZO를 Sputter를 사용해 증착했다. Parylene은 DI Water 70도에서 Floating 공정을 통해 Rigid 기판에서 탈착 시켰다. 유연한 기판 위에 TFT를 제작 후 bending에 대한 특성 변화 및 안정성에 대한 측정을 실시하였다. Bending에 대한 특성 변화는 우수한 결과가 나왔지만 안정성 측정 중 Negative Bias Stress(NBS) 상에서 비정상적인 On Current Drop 현상이 발생 되었다. Parylene과 Channel층 사이 interface roughness로 인해 charge trap이 되고 이로 인해 On Current Drop 이라는 현상으로 나타났다. 그래서 우리는 Parylene 기판과 Channel 층간의 surface roughness를 개선하기 위한 방법으로 UV Treatment를 사용하였고 시간을 다르게 하여 surface 개선을 진행했다. Treatment 시간을 증가 시킴에 따라 Surface roughness가 많이 좋아 졌으며, Surface를 개선하고자 비정상적인 On Current Drop 현상이 없어졌으며 위 실험으로 Polymer의 surface roughness에 따라 TFT에 대한 안정성에 대한 신뢰성이 확보 될 수 있는 것을 확인 하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.159-162
• /
• 2002

Ferroelectric $YMnO_{3}$ thin films were etched with $Ar/Cl_{2}$ and $CF_{4}/Cl_{2}$ inductivly coupled plasma (ICP). The maximum etch rate of $YMnO_{3}$ thin film was $300{\AA}/min$ at a $Ar/Cl_{2}$ gas mixing ratio of 2/8, a RF power of 800 W, a dc bias of 200 V, a chamber pressure of 15 mTorr, and a substrate temperature of ${30^{\circ}C}$. From the X-ray photoelectron spectroscopy (XPS) analysis ， yttrium not only etched by chemical reactions with Cl radicals, but also assisted by Ar ion bombardments in $Ar/Cl_{2}$ plasma. In $CF_{4}/Cl_{2}$ plasma, yttrium are remained on the etched surface of $YMnO_{3}$ and formed of nonvolatile YFx compounds Manganese etched effectively by chemical reactions with Cl and F radicals. From the X-ray diffraction (XRD) analysis, the (0004) diffraction peak intensity of the $YMnO_{3}$ thin film etched in $Ar/Cl_{2}$ plasma shows lower value than that in $CF_{4}/Cl_{2}$ plasma. It is indicates that the crystallinty of $YMnO_{3}$ thin film is more easily damaged by the Ar ion bombardment than the changes of stoichiometry due to nonvolatile etch by-products.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.190-194
• /
• 2002

In this study, the etching of Au thin films have been performed in an inductively coupled CF4/Cl2/Ar plasma. The etch properties were measured as the CF4 adds from 0 % to 30 % to the Cl2/(Cl2 + Ar) gas mixing ratio of 0.2. Other parameters were fixed at a rf power of 700 W, a dc bias voltage of 150 V, a chamber pressure of 15 mTorr, and a substrate temperature of $30^{\circ}C$. The highest etch rate of the Au thin film was 370 nm/min at a 10 % additive CF4 into Cl2/(Cl2 + Ar) gas mixing ratio of 0.2. The surface reaction of the etched Au thin films was investigated using x-ray photoelectron spectroscopy (XPS) analysis. From x-ray photoelectron spectroscopy (XPS) analysis, the intensities of Au peaks are changed. There is a chemical reaction between Cl and Au. Au-Cl is hard to remove on the surface because of its high melting point and the etching products can be sputtered by Ar ion bombardment. We obtained the cleaned and steep profile.