• Advances in concrete construction
• /
• v.10 no.6
• /
• pp.515-526
• /
• 2020

Cold-mixed asphalt mixture is a widely recommended asphalt pavement materials with potentially economic and environmental benefits. Due to the reduction of natural non-renewable mineral resources, powder minerals with similar properties are considered as new mineral fillers in asphalt mixtures. This study explored the feasibility of using cement to replace natural limestone powder (LP) in emulsified asphalt concrete modified by styrene-butadiene styrene copolymer. The experimental tests, including compressive strength, Marshall stability as well as moisture susceptibility test, were used to investigate the mechanical properties, the Marshall stability, flow value, as well as the moisture damage. In addition, the influence of material composition on the performance of asphalt concrete is explained by the microstructure evolution of the pore structure, the interface transition zone (ITZ), and the micromorphology. Due to mineralogical reactivity of cement, its replacement part of LP improved the mechanical properties, Marshall stability, but it will reduce the moisture susceptibility and flow value. This is because with the increase of the cement substitution rate, the pore structure of the asphalt concrete is refined, the width of ITZ becomes smaller, and the microstructure is more compact. In addition, asphalt concrete with a larger nominal particle size (AC-16) has relatively better performance.

• Elastomers and Composites
• /
• v.49 no.4
• /
• pp.323-329
• /
• 2014

In order to select polymer matrix for MIF (Molded-In Foaming) process, in this study, we investigated rheological properties of commercial polymers, SBC (Styrene-Butadiene Copolymers, K-resin KK38) and SBS (Styrene- Butadiene-Styrene, KTR 101 and KTR 301). In time sweep test, the rheological properties ($G^{\prime}$, $G^{{\prime}{\prime}}$, ${\eta}^*$) of SBS at 155 and $170^{\circ}C$ display almost constant value as a function of time from 0 s to 1800 s. On contrast, the rheological properties of SBS at 185 and $200^{\circ}C$ exponentially increase as a function of time. It could be due to gelation of SBS at high temperature conditions. These increment of rheological properties are not observed in SBC. From LAOS (large amplitude oscillatory shear) test, the nonlinear rheological properties of SBS at 155 and $200^{\circ}C$ after 1800 s are compared. The nonlinear rheological properties at $155^{\circ}C$ show simple strain thinning behavior such as linear homopolymer, however, the nonlinear rheological properties at $200^{\circ}C$ show 2 times strain thinning behavior (Payne effect). It well match with the gelation of SBS at $200^{\circ}C$. From rheological studies, it is confirmed that the proper polymer matrix for MIF process (low rheological properties at initial time and high rheological properties after process) is SBS KTR 301.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.11
• /
• pp.771-780
• /
• 2014

In this study, the various organic supports (i.e., silicone, acrylonitrile-butadiene-styrene, epoxy, and, butadiene rubber) with great sorption capacity of organic contaminants were chosen to develop nano-ZnO/organic composites (NZOCs) and to prevent the detachment of nano-ZnO particles. The water resistance of the developed NZOCs were evaluated, and the feasibility of the developed NZOCs were investigated by evaluating the removal efficiency of 1,1,2-trichloroethylene (TCE) in the aqueous phase. Based on the results from water-resistance experiments, long-term water treatment usage of all NZOCs was found to be feasible. According to the FE-SEM, EDX, and imaging analysis, nano-ZnO/butadiene rubber composite (NZBC) with various sizes and types of porosity and crack was measured to be coated with relatively homogeneously-distributed nano-ZnO particles whereas nano-ZnO/silicone composite (NZSC), nano-ZnO/ABS composite (NZAC), and nano-ZnO/epoxy composite (NZEC) with poorly-developed porosity and crack were measured to be coated with relatively heterogeneously-distributed nano-ZnO particles. The sorption capacity of NZBC was close to 60% relative to the initial concentration, and this result was mainly attributed to the amorphous structure of NZBC, hence the hydrophobic partitioning of TCE to the amorphous structure of NZBC intensively occurred. The removal efficiency of TCE in aqueous phase using NZBC was close to 99% relative to the initial concentration, and the removal efficiency of TCE was improved as the amount of NZBC increased. These results stemmed from the synergistic mechanisms with great sorption capability of butadiene rubber and superior photocatalytic activities of nano-ZnO. Finally, the removal efficiency of TCE in aqueous phase using NZBC was well represented by linear model ($R^2{\geq}0.936$), and the $K_{app}$ values of NZBC were from 2.64 to 3.85 times greater than those of $K_{photolysis}$, indicating that butadiene rubber was found to be the suitable organic supporting materials with enhanced sorption capacity and without inhibition of photocatalytic activities of nano-ZnO.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.3
• /
• pp.164-167
• /
• 2002

ABS/Polypyrrole composite film has been synthesized by means of electrochemical polymerization in order to enhance the oxidant stability by using ABS(Acrylonitrile-Butadiene-Strene) as a host-polymer. While the acetonitrile as a solvent swells the host-polymer ABS on Pt plate, and then the pyrrole in an electrolyte penetrates the Pre-coated ABS film during electrochemical Polymerization. Comparing with the sin91e-component Polypynole film, the resulting conducting ABS/PPy composite nim shows the good reliability for the uniform resistance and the enhancement of the oxidant stabilization.

• Membrane Journal
• /
• v.18 no.3
• /
• pp.256-259
• /
• 2008

In this study, graphite or zeolite 4A was mixed with poly(acrylonitrile-butadiene-strene) (ABS) to make hybrid films, and permeation characteristics of air and water vapor through these films were investigated. In all cases, gas permeabilities of hybrid films were lower than that of pure ABS films. The permeability decrease of oxygen was slightly larger than that of nitrogen, resulting in the little decrease of $O_2/N_2$ selectivity. In addition, the water vapor transfer rates (WVTR) of hybrid films were about half of ABS film's. The decrease of permeabilities may be owing to the increase of tortuosity for diffusion in hybrid films.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.637-642
• /
• 2012

The effects of mixing geometry (intermeshing vs. tangential rotor) for the dispersion and distribution of silica agglomerates in SBR/BR compound were investigated. Silica dispersion and distribution were found to be better with the intermeshing rotor compared to the tangential rotor. It was concluded that the intermeshing rotor compared to the tangential rotor delivered a higher shear stress due to interlocked rotor geometry to silica agglomerates leading to better dispersity and distribution of silica in the agglomerates.

• Elastomers and Composites
• /
• v.35 no.3
• /
• pp.215-226
• /
• 2000

Cure characteristics of carbon black-filled rubber compounds with different rubber composition were studied using a rheometer. The carbon black-filled rubber compounds with single, binary, and ternary rubber compositions of natural rubber (NR), styrene-butadiene rubber (SBR), and butadiene rubber (BR) were used. Delta-torques of the NR/BR- and SBR/BR-based compounds with a high BR content were higher than those of the single rubber-based compounds. For ternary rubber-based compounds, the delta-torques of the compounds were lower when the difference in the rubber content ratios was small than when it was big. Scorch and optimum cure times of the rubber compounds became shorter by increasing the content of NR in the compounds while those became longer by increasing the SBR content. Cure rates of the rubber compounds increased with a decrease of the SBR content in the rubber compounds. Reversion ratios decreased with an increase of the SBR content in the rubber compounds.

• Elastomers and Composites
• /
• v.54 no.2
• /
• pp.97-104
• /
• 2019

Emulsion styrene-butadiene rubber silica wet masterbatch (ESBR silica WMB) technology was studied to develop highly filled and highly dispersed silica compounds, involving the preparation of a composite by co-coagulating the modified silica and the rubber latex in a liquid phase. Previous studies have shown that when manufacturing ESBR silica WMB/Butadiene silica dry masterbatch (BR silica DMB) blend compounds, preparing BR silica dry masterbatch and mixing it with ESBR silica WMB gave excellent results. However, WMB still has the problem of lower crosslink density due to residual surfactants. Therefore, in this study, tetrabenzylthiuram disulfide (TBzTD) was added instead of diphenyl guanidine (DPG) in the ESBR silica WMB/BR silica DMB blend compounds and sulfur/CBS contents were increased to evaluate their cure characteristics, crosslink densities, mechanical properties, and dynamic viscoelastic properties. TBzTD was found to be more effective in increasing the crosslink density and to produce superior properties compared to DPG. In addition, with increasing sulfur/CBS contents, mechanical properties and rolling resistance were enhanced due to high crosslink density, but the abrasion resistance was not significantly changed because of the toughness.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.189-190
• /
• 2002

Rolling-sliding friction was investigated for three SBR (styrene-butadiene rubber) specimens including silica-filled, HAF carbon black-filled, and SAF carbon black-filled SBR. When a rubber wheel was rolled against a glass disk, the coefficient of friction varied with the slip ratios. The coefficient of friction for the silica-tilled SBR showed the highest value of the rubber specimens examined under various slip ratios. The contact areas of silica-filled SBR were larger than those of the carbon black-filled SBRs, as indicated the modulus of the silica-filled SBR showing the lowest value. The contact area during rolling-sliding friction was always smaller than those during the static contact. The friction force at the unit contact area for the silica-filled SBR under braking and driving was higher than those of carbon black-filled SBRs.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.3
• /
• pp.157-166
• /
• 1992

해수환경하의 콘크리트 구조물은 동결융해의 반복에 의한 물리적인 침식과 해수중에 용존하는 각종의 이온들의 침투로 인한 화학적 침식에 의해 현저한 성능저하현상을 나타내는 것으로 알려져있다. 본 연구는 포졸란계 혼합재인 플라이 애쉬, 슬래그, 슬리카 흄과 폴리머계 혼합재인 Ethylene Vinyl Acetate(EVA), Styrene-Butadiene Rubber(SBR)를 사용하여 제조한 콘크리트 경화체의 해수환 경하에서 동결융해 저항성에 미치는 혼합재의 종류 및 첨가량의 영향, W/C의 영향을 비교 검토한 실험적 연구이다. 콘크리트의 동결융해 저항성을 위해서는 공기연행이 필수적이며, 공기연행시킨 경우 W/C가 낮을수록 동결융해 저항성이 우수하였다. 해수중에서의 동결융해 저항성은 슬래그분말을 첨가할 때 우수하였으며, 폴리머계 혼합재에서는 EVA가 우수한 결과를 나타내었다.