• Journal of the Korean Geotechnical Society
• /
• v.24 no.4
• /
• pp.79-88
• /
• 2008

Recently, the high speed railway comes into the spotlight as the important and convenient traffic infrastructure. In Korea, Kyung-Bu high speed train service began in bout 400 km section in 2004, and the Ho-Nam high speed railway will be constructed by 2017. The high speed train will run with a design maximum speed of 300-350 km/hr. Since the trains are operated at high speed, the differential settlement of subgrade under the rail is able to cause a fatal disaster. Therefore, the differential settlement of the embankment must be controlled with the greatest care. Furthermore, the characteristics and causes of settlements which occurred under construction and post-construction should be investigated. A considerable number of studies have been conducted on the settlement of the natural ground over the past several decades. But little attention has been given to the compression settlement of the embankment. The long-term settlement of compacted fills embankments is greatly influenced by the post-construction wetting. This is called 'hydro collapse' or 'wetting collapse'. In spite of little study for this wetting collapse problem, it has been recognized that the compressibility of compacted sands, gravels and rockfills exhibit low compressibility at low pressures, but there can be significant compression at high pressures due to grain crushing (Marachi et al. 1969, Nobari and Duncan 1972, Noorany et al. 1994, Houston et al. 1993, Wu 2004). The characteristics of compression of fill materials depend on a number of factors such as soil/rock type, as-compacted moisture, density, stress level and wetting condition. Because of the complexity of these factors, it is not easy to predict quantitatively the amount of compression without extensive tests. Therefore, in this research I carried out the wetting collapse tests, focusing on various soil/rock type, stress levels, wetting condition more closely.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.41 no.1
• /
• pp.47-55
• /
• 2023

In this study, the following conclusions were drawn by analyzing the size, proportion, shape, angle, distribution, etc. of stones in order to identify the principles of facade molding of stonework of the 5th to 7th centuries of the Silla Dynasty. First, the uniformity of the size of the stones of the stone foundations of the Silla Dynasty was low at -0.8 to 4.1. This means that stones of various sizes were used, from small stones to large stones. In addition, the distribution of large stones in stonework of the Silla Dynasty appeared evenly regardless of height. This was common in the stonework of the Silla Dynasty, regardless of structural classification such as wells and mountain fortresses. It is thought that the Silla people did not only pursue practicality and efficiency in stone construction, but also considered design elements. Second, the proportional deviation of the stones of the stone walls of the Silla Dynasty was high, ranging from 0.861 to 1.515. This means that the stonework of the Silla Dynasty did not use only long flagstone-shaped stones, but used a mixture of long and short stones. Third, the shape average of the stones of the stonework of the Silla Dynasty was low at 0.45, and the shape deviation was high at the maximum of 0.15. This means that the stones as a whole have irregular shapes, and each stone has a high difference in shape. Fourth, the angle deviation of the stones of the Silla Dynasty was 4.3 to 16.2, and the average angle was 2. This means that the angle of each stone on the stone axis of the Silla Dynasty is tilted to the left and right. Fifth, there was no correlation between stone size, slenderness ratio, shape, and angle in the stone axes of the Silla Dynasty. In the case of stone axes in the Joseon Dynasty, there was a positive correlation between stone size and slenderness, and a negative correlation between stone size and shape. It can be said that the stones of the Joseon Dynasty were relatively standardized, but the Silla Dynasty showed the beauty of moderation by keeping the nature of the material and becoming one with the material.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.1
• /
• pp.54-60
• /
• 2022

The planting date of corn for silage has been delayed because of spring drought and double cropping system in Korea. This experiment was conducted to evaluate agronomic characteristics, forage production and feed value of corn at April and May in 2019. Experimental design was a split-plot with three replications. Planting dates (12 April and 10 May) were designated to the main plot, and corn hybrids ('P0928', 'P1543' and 'P2088') to the subplot. The silking days of the early planting date (12 April) was 79 days and that of the late planting date (10 May) was 66 days (p<0.0001), however, there were no significant differences among the corn hybrids. Ear height of the late planting date was higher than that of the early planting (p<0.05), while there were no significant differences in plant height of corn. Insect resistance at the early planting was lower than that of late planting (p<0.05), however, lodging resistance was no significant difference at planting date. The rice black streaked virus (RBSDV) infection of early planting was 3.7% and that of late planting was 0.3% (p<0.001). Dry matter (DM) contents of stover, ear and whole plant had significant difference at planting date (p<0.05). And differences in ear percentages were observed among the corn hybrids (p<0.01). And ear percentages of early maturing corn ('P0928') was higher than for other hybrids. Ear percentage at the early planting date was higher than that at the late planting date (p<0.01). DM and total digestible nutrients (TDN) yields had significant difference at planting date, however, there were no significant differences among the corn hybrids. DM and TDN yields at the late planting (21,678 kg/ha and 14,878 kg/ha) were higher than those of the early planting (13,732 kg/ha and 9,830 kg/ha). Crude protein content at the early planting date was higher than that of the late planting. Acid detergent fiber content of the late planting was lower than that of the early planting date (p<0.01), while there were no significant neutral detergent fiber content difference among the corn tested. Calculated net energy for lactation (NE_L) and TDN at the early planting were higher than those of at the late planting (p<0.01). Results of this our study indicate that the late planting date (May) is better than early planting date (April) in forage yield and feed value of corn. Therefore, the delay of planting date by May was more suitable for use in cropping system.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.1
• /
• pp.41-46
• /
• 2022

To investigate the domestic seed production potential of Italian ryegrass, it was sown in autumn in the southern region and harvested in the spring of the following year to investigate the productivity and quality of seeds and straw. Italian ryegrass (Lolium multiflorum Lam.) 'GreenCall' variety was sown in Jinju, Gyeongnam in the fall of 2020 with three seeding rates (20, 30 and 40 kg/ha). The experiment was arranged consisted of a randomized block design with three replications. The ryegrass was sown on October 17, 2020, and the harvest was on May 31, about 60 days from the heading stage. The heading stage of Italian ryegrass was April 28, and there was no difference among treatments. Plant height was significantly shorter in the 40 kg/ha seeding treatment group, and there was no significant difference in the remaining treatments. The resistance of lodging, disease, and cold did not show significant differences among treatments. Spike length and number of seeds per spike were highest at 20 kg/ha seeding amount, and there was no difference in the remaining treatments. The seed yield was the highest at 1,956 kg/ha in the 20 kg/ha seeding rate, and there was no difference in the 30 and 40 kg/ha seeding rates. The dry matter content of seeds and straws was 45.60 and 41.83% on average, and there was no significant difference among treatments. The amount of remaining straw after seed harvesting was found to be 7,689 kg/ha on average on a dry basis, and it was high in the 40 kg/ha sowing area, but there was no significant difference among treatments. According to the above results, it was found that it is most advantageous to sow at 20 kg/ha when producing Italian ryegrass seeds through autumn sowing in the southern region.

• Journal of agriculture & life science
• /
• v.50 no.5
• /
• pp.163-172
• /
• 2016

Four growing Hanwoo cattle weighing 200±11.7kg were used within 4×4 Latin square design to establish nutrient requirements for Hanwoo growing steers under severe heat stress. The steers were fed four different energy level diets; 100%(control), 100%(E100), 115%(E115) and 130%(E130) of energy levels of growing Hanwoo steers based on total digestible nutrient level suggested by the Korea Feeding Standard for Hanwoo using timothy hay and commercial concentrate. The steers in the control were housed with no stress, whereas the steers in the other groups were under severe heat stress. The severe heat stress significantly decreased(p<0.05) true digestibility of dry matter(i.e. control 81.5% vs E100 79.1, E115 77.0 and E130 76.0, respectively). The severe heat stress and different energy intake levels did not affect blood physiological metabolites and body temperature of the growing steers. Based on changes in average daily gain by different energy intake level, the equation(Y=0.235X+115.03) of energy requirement of growing Hanwoo steers without changes in body weight was calculated, indicating that, compared with the present energy intake suggested by Korean feeding standard, 15.03% of dietary energy for maintenance of growing Hanwoo steers under severe heat stress should be increased.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.5B
• /
• pp.603-614
• /
• 2008

End-uses of household water have been changed by a life style, housing type, weather, water rate and water supply facilities etc. and those variables can be considered as an internal and exogenous factors to estimate long-term demand forecasts. Analysis of influential factors on water consumption in households would give an explanation to cause on the change of trend and would help predicting the water demand of end-use in household. The purpose of this study is to analyze the demand trends and patterns of household water uses by metering and questionnaire such as occupation, revenue, numbers of family member, housing types, age, floor area and installation of water saving device, etc. The peak water uses were shown at Saturday among weekdays and July in a year based on the analysis results of water use pattern. A steep increase of total water volume can be found in the analysis of water demand trend according to temperature from $-14^{\circ}C$ to $0^{\circ}C$, while there are no significant variations in the phase of more than $0^{\circ}C$, with an almost stable demand. Washbowl water shows the highest and toilet water shows the lowest relation with temperature in correlation analysis results. In the results of ANOVA to find the significant difference in each unit water use by exogenous factors such as housing type, occupation, number of generation, residential area and income et al., difference was shown in bathtub water by housing type and shown in kitchen, toilet and miscellaneous water by numbers of resident. Especially, definite differences in components except washbowl and bathtub water, could be found by numbers of resident. Based on the result, average residents in a house should be carefully considered and the results can be applied as reference information, in decision making process for predicting water demand and establishing water conservation policy. It is expected that these can be used as design factors in planning stage for water and wastewater facilities.

• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.3
• /
• pp.189-197
• /
• 2023

Purpose. This study aimed to compare and evaluate the shear bond strength between various temporary prostheses resin blocks fabricated by subtractive and additive manufacturing methods bonded to self-curing reline resin. Materials and methods. The experimental groups were divided into 4 groups according to the manufacturing methods of the resin block specimens and each specimen was fabricated by subtractive manufacturing (SM), additive manufacturing stereolithography apparatus manufacturing (AMS), additive manufacturing digital light processing manufacturing (AMD) and conventional self-curing (CON). To bond the resin block specimens and self-curing resin, the reline resin was injected and polymerized into the same location of each resin block using a silicone mold. The shear bond strength was measured using a universal testing machine, and the surface of the adhesive interface was examined by scanning electron microscopy. To compare between groups, one-way ANOVA was done followed by Tukey post hoc test (α = 0.05). Results. The shear bond strength showed higher values in the order of CON, SM, AMS, and AMD group. There were significant differences between CON and AMS groups, as well as between CON and AMD groups. but there were no significant differences between CON and SM groups (P > .05). There were significant differences between SM and AMD groups, but there were no significant differences between SM and AMS groups. The AMS group was significantly different from the AMD group (P < .001). The most frequent failure mode was mixed failures in CON and AMS groups, and adhesive failures in SM and AMD groups. Conclusion. The shear bond strength of SM group showed lower but not significant bond strength compared to the CON group. The additive manufacturing method groups (AMS and AMD) showed significantly lower bond strength than the CON group, with the AMD group the lowest. There was also a significant difference between the AMD and SM group.

• Journal of Korea Entertainment Industry Association
• /
• v.13 no.6
• /
• pp.211-220
• /
• 2019

It helps to wisely abstain from errors of the a priori subjective emotions related to human emotions, and orders emotions to make rational choices. These emotional happiness of human and moral sensitivities work directly or indirectly in rational choice of rational thought and reason. Abraham would have been troubled by the divine mandate to sacrifice a son who was only one, and a son who had been healed. Was his reason reasonable at this time? In rational reason, it can be said that the act of dedicating his son is an appropriate act, but is it possible in the human mind? Aristoteles also called human virtue virtue in good for human beings. Because happiness is also a mental activity, we have to know a certain degree about the mind. This ψυχή(psyche, spirit) spirit is an irrational element that is invisible but an intervention in rational principles. Also C. G. Jung states that all human beings have four dynamic psychological functions that are not visible, and that the mind is driven by these four functional dimensions. This means that the elements of S, Sensing, N, Intuition, T, Thinking, and Feeling are combined. David Hume also emphasized the principle of empathy, asserting that morality can not be derived from reason, and Max Ferdinand Scheler, before grasping the visual characteristics of a person, has already captured the whole feeling of the person, And that the value given to this feeling is the value, and that the function of emotion that is elevated to the perceived object by grasping the value through this process and the value is always preceded by the reason. Emmanuel Levinas states that emotional emotions of love are ahead of reason and that emotions precede human reasoning and rationality is the inability of emotional control that we need rational thought and rational and wise action as reason of control and temperance. As part of human emotional education, in the 7th curriculum, Bloom's cognitive, perceptive, and behavioral domain, which is a person with integrated thinking, is trying to be a moral practitioner. It focuses on how to act according to the direction of emotions for virtuous acts and how to develop emotions for emotions on behalf of vicious acts. We can design the possibility and direction of cultivating human emotions and emotional happiness and happy sensitivities by the principle of strengthening virtue and the principle of elimination of ill feeling.

• Journal of Practical Engineering Education
• /
• v.15 no.1
• /
• pp.119-126
• /
• 2023

Today, in order to improve fuel efficiency and dynamic behavior of automobiles, an era of light weight and simplification of automobile parts is being formed. In order to simplify and design and manufacture the shape of the product, various components are integrated. For example, in order to commercialize three products into one product, product processing is occurring to a very narrow area. In the case of existing parts, precision die casting or casting production is used for processing convenience, and the multi-piece method requires a lot of processes and reduces the precision and strength of the parts. It is very advantageous to manufacture integrally to simplify the processing air and secure the strength of the parts, but if a deep and narrow pocket part needs to be processed, it cannot be processed with the equipment's own spindle. To solve a problem, research on cutting processing is being actively conducted, and multi-axis composite processing technology not only solves this problem. It has many advantages, such as being able to cut into composite shapes that have been difficult to flexibly cut through various processes with one machine tool so far. However, the reality is that expensive equipment increases manufacturing costs and lacks engineers who can operate the machine. In the five-axis cutting processing machine, when producing products with deep and narrow sections, the cycle time increases in product production due to the indirectness of tools, and many problems occur in processing. Therefore, dedicated machine tools and multi-axis composite machines should be used. Alternatively, an angle spindle may be used as a special tool capable of multi-axis composite machining of five or more axes in a three-axis machining center. Various and continuous studies are needed in areas such as processing vibration absorption, low heat generation and operational stability, excellent dimensional stability, and strength securing by using the angle spindle.

• Korean Journal of Construction Engineering and Management
• /
• v.24 no.6
• /
• pp.24-35
• /
• 2023

Recently, the Ministry of Land, Infrastructure and Transport presented the '6th Construction Technology Promotion Basic Plan' and 'Smart Construction Revitalization Plan (2022.7.20)'. Off-Site Construction (OSC), which involves construction and production of PC (Precast Concrete) and Modular, etc., has advantages in shortening the construction period, reducing costs, improving quality, reducing construction waste, and reducing safety accidents. However, the construction cost is high compared to the traditional RC construction method, which has hindered its utilization and spread. In this study, OSC utilization was improved. An economic analysis indicator and methodology that can support decision-making in the planning and design stages for multi-unit housing were proposed. The factors used in the economic analysis of OSC (based on the PC method) of apartment houses were reviewed. As for the indicators used in the cost and benefit section, 'Construction Period', 'Disaster Occurrence', 'Waste Generation', and 'Greenhouse gas Emission', which reflect the technical advantages of OSC, were derived. In addition, a scenario analysis was conducted based on actual apartment housing case data for the presented economic analysis indicators and benefit calculation standards. The level of benefit that offsets the difference between the existing RC construction method and the construction cost was reviewed. In future studies, it will be necessary to conduct additional case studies to apply the measurement criteria for detailed indicators and supplement the benefit indicators.