• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.402-405
• /
• 2001

The BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics were prepared by conventional mixed oxide method. The structural and dielectric properties of the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics with the sintering temperature were investigated. Increasing the sintering temperature, the 2$\theta$ value of BaTiO$_3$peaks were shifted to the higher degree and intensity of the BaTiO$_3$and BaNbO$_3$peaks were increased. In the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics sintered at 135$0^{\circ}C$ and 1375$^{\circ}C$, the grain was fine and uniform. Increasing the sintering temperature, the pore was decreased and the dielectric constant was increased. In the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics sintered at 1375$^{\circ}C$, the dielectric constant and dielectric loss were 5424, 0.02 respectively.ctively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.693-696
• /
• 2001

The (Ba$_{0.3}$Bi$_{0.3}$Sr$_{0.4}$)TiO$_3$[BBST] ceramics were prepared by conventional mixed oxide method. The structural properties of the BBST ceramics with sintering temperature were investigated by XRD, SEM, EDS. In the case of BBST ceramics sintered at 1150~135$0^{\circ}C$, the $Ba_{0.5}$Sr$_{0.5}$TiO$_3$and SrBi$_4$Ti$_4$O$_{15}$ phase were coexisted. The 2$\theta$ value of the BST (110) peaks were shifted to the lower degree at the sintering temperature of 130$0^{\circ}C$ and 135$0^{\circ}C$. The grains of the BBST ceramics sintered at 130$0^{\circ}C$ and 135$0^{\circ}C$ were not appeared. Increasing the sintering temperature, the densities of the BBST ceramics were increased. In the BBST ceramics sintered at 130$0^{\circ}C$ and 135$0^{\circ}C$, the mole ratio of Bi was decreased.d.ed.d.d.d.

• 한국생산제조학회지
• /
• 제19권2호
• /
• pp.211-215
• /
• 2010

Continuous contraction and expansion of disk brake can be due to friction and temperature difference at repeated sudden braking. As serious vibration at disk is produced, the braking force will be changed ununiformly and braking system can not be stabilized. Temperature and heat flux at disk brake are investigated by structural and thermal analysis in this study. The maximum equivalent stress and displacement are shown respectively at the ventilated hole and the lower part of disk plate. At thermal analysis of initial state, temperature on disk plate is distributed from $95.9^{\circ}C$ to $100^{\circ}C$. The maximum heat flux of $0.0168W/mm^2$ is shown at the inner friction part between disk plate and pad. At thermal analysis of transient state, temperature on disk plate is distributed from $95^{\circ}C$ to $96.5^{\circ}C$ after 100 second. The maximum heat flux of $0.0024W/mm^2$ is also shown at the inner friction part between disk plate and pad. By comparing with initial state, the temperature on disk plate is more uniformly distributed and heat flux is more decreased by 7 times at transient state.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.88-92
• /
• 2002

$Ba(Zn_{0.8}Co_{0.2})_{1/3}Ta_{2/3}O_3$ [BZCT(80/20)] ceramics were prepared by the conventional mixed oxide method. The ceramics were sintered at the temperature of $1450{\sim}1550^{\circ}C$ for 5hr. in air. The structural properties of BZCT(80/20) ceramics were investigated as a function of sintering temperature. The BZCT(80/20) ceramics sintered at $1550^{\circ}C$ showed a polycrystalline complex perovskite structure without second phases and any unreacted materials. Increasing the sintering temperature, the bulk density and ordering were increased. The bulk density of the BZCT(80/20) ceramics sintered at $1550^{\circ}C$ was 7.50[$g/cm^2$]. Increasing the sintering temperature, the average grain size were increased and pore were decreased.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.181-184
• /
• 2008

오스테나이트 계열 스테인리스강의 경우 뛰어난 내열성으로 인해 가스 터빈 블레이드나 디스코 등으로 많이 사용되고 있다. 본 연구에서는 터빈 블레이드로 사용되는 316 스테인리스강의 고온 인장 및 저주기 피로 물성을 실험적으로 구하였다. 실험 결과 탄성계수와 항복강도, 최대인장강도 모두 온도 증가에 따라 감소하는 것으로 확인되었다. 소성변형률 진폭, 소성변형률 에너지 등의 인자들이 피로파괴에 미치는 영향도 조사하였다. 실험을 통해 얻어진 고온 인장 물성을 이용하여 316 스테인리스강으로 제작된 가스터빈 블레이드의 구조해석을 수행하였다.

• 한국기계가공학회지
• /
• 제20권7호
• /
• pp.48-57
• /
• 2021

The main research content of this paper is to evaluate the structural integrity and the cooling performance of 4250 kVA power transformer with ONAN(Oil Natural and Air Natural) mode. The dynamic analysis is used to verify the structural safety of the transformer by seismic loading. The transformer structure is simplified and NX software is used to build a three-dimensional model, and ANSYS commercial software is used to calculate the stress and deformation by applying corresponding load. The analysis result was evaluated whether it satisfies the design requirements according to the IEEE Std 693 standard. In terms of thermal analysis to evaluate the cooling performance, the thermal physical model is used to calculate the heat exchange between the radiator and the tank in the steady state, and the result is input into the Fluent software to calculate the internal temperature field of the transformer tank, which reduces the calculation cost of thermal fluid. Comparing the simulated hot spot temperature and top oil temperature of the transformer with the calculation results of the IEC60076 classic model, it is found that the error is only 1.9%.

• Steel and Composite Structures
• /
• 제6권2호
• /
• pp.159-182
• /
• 2006

Current fire design codes for determining the temperature within the structural elements that form part of a complete building are based on isolated member tests subjected to the standard fire. However, the standard time-temperature response bears little relation to real fires and doesn't include the effects of differing ventilation conditions or the influence of the thermal properties of compartment linings. The degree to which temperature uniformity is present in real compartments is not addressed and direct flame impingement may also have an influence, which is not considered. It is clear that the complex thermal environmental that occurs within a real building subject to a natural fire can only be addressed using realistic full-scale tests. To study global structural and thermal behaviour, a research project was conducted on the eight storey steel frame building at the Building Research Establishment's Cardington laboratory. The fire compartment was 11 m long by 7 m wide. A fire load of $40kg/m^2$ was applied together with 100% of the permanent actions and variable permanent actions and 56% of live actions. This paper summarises the experimental programme and presents the time-temperature development in the fire compartment and in the main supporting structural elements. Comparisons are also made between the test results and the temperatures predicted by the structural fire Eurocodes.

• 한국군사과학기술학회지
• /
• 제17권4호
• /
• pp.413-421
• /
• 2014

Since the structural temperature of a flight vehicle flying at high speed rises rapidly due to aerodynamic heating, it is necessary for optimum structural design to obtain proper material properties at high temperature by taking into account of its operational environment. For a special alloy, analysis data on strength change due to exposure time to high temperature are very limited, and most of them are for an exposure time longer than 30 minutes for long term operations. In this study, base and weld metal samples of Ti-6Al-4V alloy had been prepared and high temperature tensile tests with induction heating were performed, and then high temperature strength characteristics and strength recovery characteristics through cooling have been analyzed. Pre-tests to determine maximum heating rate were performed, and response characteristics for temperature control were confirmed. As a result, high temperature tensile strength appeared to be lower than that of room temperature, but it was higher than that of high temperature of 30 minite exposure listed in MMPDS. In strength recovery through cooling Ti-6Al-4V alloy has shown higher recovery rate compared with other alloys.

• 대한기계학회논문집A
• /
• 제22권1호
• /
• pp.64-72
• /
• 1998

This paper was undertaken to develop the fracture toughness testing method using small and single specimen compared to the conventional method in evaluating elastic-plastic fracture toughness of the superconducting magnet structural material at cryogenic temperature. The elastic-plastic fracture toughness test was conducted by using the unloading compliance method recommended by ASTM E813-89 to accomplish the above purpose. And, the 20% side-grooved 0.5TCT and 1TCT specimens were used to evaluate the fracture toughness by using as possible as miniaturized CT specimen. The unloading compliance method was a very useful method in evaluating elastic-plastic fracture toughness at cryogenic temperature. It could be taken valid fracture toughness values by using 20% side-grooved 0.5TCT specimen recommended by ASTM E813-89.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.666-671
• /
• 2007

To acquire the safety along with durability of mechanical machinery products, we should consider the structural mechanics such as stress, deformation and dynamic vibration characteristics and identify those important aspects in the stage of preliminary design engineering. This cryogenic ball valve is used to transfer the liquified natural gas which temperature is $-196^{\circ}C$, supplied pressure is $168kg/cm^2$. For the cryogenic ball valve, the assurance of structural integrity and operability are essential to meet not only normal, abnormal loading conditions but also functionality during a seismic event. In this thesis, analytical approach and results using finite element analysis and computational method are herein presented to evaluate the aspects of structural integrity along with operability of cryogenic ball valve. In this study, we designed the high pressure cryogenic ball valve that accomplishes zero leakage by elastic seal at normal temperature and metal seal at high temperature.