• Journal of the Korean GEO-environmental Society
• /
• v.22 no.12
• /
• pp.41-50
• /
• 2021

This study investigated the changes in engineering characteristics of sand-tire chip mixtures during repetitive loading. To quantify the changes in the maximum shear modulus according to the tire chip content in the mixtures and the particle size ratio between sand particle and tire chip, the samples were prepared with tire chip content of TC = 0, 10, 20, 40, 60, and 100%, and the particle size ratios SR were also set to be SR = 0.44, 1.27, 1.87, and 4.00. The stress of the prepared sample was applied through a pneumatic cylinder. The experiment was conducted in the order of static loading (= 50 kPa), cyclic loading (= 50-150 kPa), static loading (= 400 kPa) and unloading. The stress applied to tested mixtures was controlled by a pressure panel and a pneumatic valve by using an air compressor. The shear wave velocity was measured during static and cyclic loadings by installing bender elements at the upper and lower caps of the mold. The results demonstrated that the change in maximum shear modulus of all tested materials with varying SR during repetitive loading is the most significant when TC ~ 40%. In addition, the mixture with smaller SR at a given TC shows greater increase in maximum shear modulus during repetitive loading.

• Composites Research
• /
• v.30 no.2
• /
• pp.77-83
• /
• 2017

Liquid silicon infiltration, which is one of the methods of producing fiber reinforced ceramic composites, has several advantages such as low fabrication cost and good shape formability. In order to confirm LSI process feasibility of SiC fiber, $SiC_f/SiC$ composites were fabricated using three types of SiC fibers (Tyranno SA, LoxM, Tyranno S) which have different crystallinity and oxygen content. Composites that were fabricated with LSI process were well densified by less than 2% of porosity, but showed an obvious difference in 3-point bending strength according to crystallinity and oxygen content. When composites in LSI process was exposed to a high temperature, crystallization and micro structural changes were occurred in amorphous SiOC phase in SiC fiber. Fiber shrinkage also observed during LSI process that caused from reaction in fiber and between fiber and matrix. These were confirmed with changes of process temperature by SEM, XRD and TEM analysis.

• Journal of the Korean Society of Costume
• /
• v.22
• /
• pp.23-44
• /
• 1994

The purpose of this study was to clarify the cultural characteristic of dress and adornments by examining articles on dress adornments and related items in Korean newspaper over periods historically and objectively by means of content analysis. This study attempted to at-tain a macro-cultural view by analysing to at-tain a macro-cultural view by analysing closely the cultural characteristics of dress and adornments as a micro-cultural system through culturally based model suggested by hamilton. The two-hundreds and eighty articles on dress and adornments were selected from newspapers(most by form Chosun Ilbo and partly from Maeil Shinbo) pulished between 1920 and 1990. The results were as follows: 1. The culture of dress and adornment received much attention during the 1930's and 1960's and little during 1950's. 2. Various cultural characteristics of dress and adornments appeared on and after 1960's: reporting more foreign news items showing foreign-oriented and future-oriented features showing cultural relativism. In the 1920's and 1970's the contents of news items on dress and adornments show the most common- mass- oriented character. Foreign-oriented cultural tendencies in cloth-ing were increasing during from 1960's to 1970's but the tendencies were turned to rather tradition-oriented features on and after 1980's compare with 1960's-1970's. Advisory critical articles on dress and adornments were small in number and insignificant but compare with other periods these received much atten-tion during the 1920's and 1980's. 3. Ideological components received much at-tention on and after 1920's to 1990. Techo-nological components received much attention during 1920's and little during 1960's. The social structural components received a little attention on and after 1920's-1940's and 1990. 4. News items on women's dress and adornments received much attention from the 1920's to 1960's and news items on both men's and women's dress and adorments were in-creasing and received much attention on and after the 1970's. 5. The pragmatic cultures were mostly re-lated to techonological components and evaluative-normative culture were mostly re-lated to ideological and social structural components. In the light of these results dress and adorments as a cultural sub-system comprise a dynamic inteacting system that articulated directly with the macro-cultural system.

• Proceedings of the SCSK Conference
• /
• 2003.09b
• /
• pp.200-200
• /
• 2003

Intact mammalian hair and wool fibres are multi-compartmental composite materials consisting of a sulphur-rich outer protective cuticle layer surrounding elongated, highly keratinized, cortex cells. The cortex cells themselves are made up of crystalline, filamentous, low-sulphur a-helical keratin molecules embedded in a matrix of highly cross-linked, globular high-sulphur keratins. It is the structurally organised and highly disulphide cross-linked nature of these materials that provides them with their remarkable mechanical properties. However these mechanical properties are sensitive to environmental conditions such as water content, temperature and chemical treatment and the importance of their ultra-structural arrangements to overall mechanical properties in different environments is still not fully understood.(omitted)

• The Korean Journal of Ceramics
• /
• v.2 no.2
• /
• pp.89-94
• /
• 1996

Aluminum and zinc titanium silicate sol-gel films were fabricated for application of waveguide and the effect of additions of ZnO and $Al_2O_3$ to binary titanium silicate films was investigated. During firing, the films are densified as they shrunk and their refractive index increases in the range of 1.58-1.83 depending on the film composition. The attenuation of the waveguides is not sensitive to changes in composition except for zinc titanium silicate waveguides which have substantially higher attenuation. However, the increase in the attenuation with aging of the waveguides depend upon the composition of waveuides. The addition $Al_2O_3$ or the reduced $SiO_2$ content in the composition appears to slow the deterioration of the waveguides due to the formation of more stable bonds and increased acidity on the film surface. Also, the wavelength dependence of the attenuation of the waveguides varies with composition. The attenuation of the waveguides except for the $65SiO_2{\cdot}35TiO_2$ composition are not Rayleigh scatter limited, suggesting the absorption loss of the waveguides due to the effects of residual carbon and structural defects in the films.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.1
• /
• pp.426-445
• /
• 2012

Conventional rate control (RC) schemes for H.264 video coding usually regulate output bit rate to match channel bandwidth by adjusting quantization parameter (QP) at fixed full frame rate, and the passive frame skipping to avoid buffer overflow usually occurs when scene changes or high motions exist in video sequences especially at low bit rate, which degrades spatial-temporal quality and causes jerky effect. In this paper, an active content adaptive frame skipping scheme is proposed instead of passive methods, which skips subjectively trivial frames by structural similarity (SSIM) measurement between the original frame and the interpolated frame via motion vector (MV) copy scheme. The saved bits from skipped frames are allocated to coded key ones to enhance their spatial quality, and the skipped frames are well recovered based on MV copy scheme from adjacent key ones at the decoder side to maintain constant frame rate. Experimental results show that the proposed active SSIM-based frameskip scheme acquires better and more consistent spatial-temporal quality both in objective (PSNR) and subjective (SSIM) sense with low complexity compared to classic fixed frame rate control method JVT-G012 and prior objective metric based frameskip method.

• Structural Engineering and Mechanics
• /
• v.90 no.2
• /
• pp.107-116
• /
• 2024

This study examined the changes in the mechanical properties of coral concrete under different coconut fiber admixtures. To accomplish this goal, the compressive strength, splitting tensile strength, flexural strength and elastic modulus properties of coral concrete blocks reinforced with coconut fibers were measured. The results showed that the addition of coconut fiber had little effect on the cube and axial compressive strengths. With increasing coconut fiber content, the flexural strength and splitting tensile strength of the concrete changed substantially, first by increasing and then by decreasing, with maximum increases of 36.0% and 12.8%, respectively; additionally, the addition of coconut fibers resulted in a failure type with some ductility. When the coconut fiber-reinforced coral concrete was 7 days old, it reached approximately 74% of its maximum strength. The addition of coconut fiber did not affect the early strength of the coral concrete mixed with seawater. When the amount of coconut fiber was no more than 3 kg/m3, the resulting concrete elastic modulus decreased only slightly from that of a similar concrete without coconut fiber, and the maximum decrease was 5.4%. The optimal dose of coconut fiber was 3 kg/m3 in this study.

• Journal of architectural history
• /
• v.10 no.2 s.26
• /
• pp.55-71
• /
• 2001

This study reviewed the preservation status of the Early Western Style Architecture in Korea based on the on-site research of church buildings which are registered as National Cultural Properties. I have investigated 21 church buildings regarding the frequency, content and concept of restoration. The results are summarized as follows First, the churches have been restored extensively in every 17 years on the average. Second, the main restorations are replacement of bricks, painting, waterproofing, repair of roof and timber. And the main changes are extension of plan, removal of Interior posts, and replacement of floor. Third, the main concept of restorations are historical restoration(62%), critical restoration(23%), stylistic restoration(14%). Forth, the category of restoration have been changed, that is extending of incompletion (1st stage), functional improvement and extension of the span of life(2nd stage), improvement of facilities(3rd stage), restoration to the original state and conservation(4th stage). Fifth, the issues of repairing techniques are revival and replacement of weathered bricks, the removal of painting, and structural reinforcement. This study will be able to be used as the fundamental materials to improve the techniques of restoration of Early Western style masonry buildings.

• Bulletin of the Korean Chemical Society
• /
• v.13 no.4
• /
• pp.425-428
• /
• 1992

Sodium substituted samples of $Y_{1-x}Na_xBa_2Cu_3O_{7-y}$ for $0.00{\leq}x{\leq}0.16$ were prepared and characterized by X-ray powder pattern, electrical resistivity and magnetic susceptibility measurements, Raman spectroscopy, and idometric titration. The Na substituted compounds have narrow solid solution limits where $0.00{\leq}x{\leq}0.16.$ As the Na concentration increases, the parent orthorhombic structure tends to gradually change to tetragonal. Small changes in the superconducting transition temperature, Tc, are observed in this solid solution region. Raman spectra for the Na phases are virtually identical with that of $YBa_2Cu_3O_7$ except that the Cu(1)-O(4) stretching mode at 504 $cm^{-1}$ and the Cu(2)-O(2,3) bending mode at 340 $cm^{-1}$ for x = 0.16 are slightly shifted. The hole concentrations of the sodium substituted compounds ranged from 0.31 to 0.33 per Cu site are increased with Na content. The substitution of $Na^+$ for $Y^{3+}$ site appears to create oxygen vacancies in the Cu-O chains, causes structural change from orthorhombic to tetragonal, and increases hole concentration in the substituted system.

• Elastomers and Composites
• /
• v.55 no.2
• /
• pp.114-119
• /
• 2020

The effect of a greenhouse-covering material on its indoor environment and on the characteristics of cherry tomatoes grown in it was investigated. The conventional polyethylene (PE) film on the greenhouse roof was replaced by a polycarbonate (PC) sheet, while maintaining the main structural frame intact. Color changes and the formation of water droplets on the PC surface were avoided by applying coextrusion and coating layers. When compared to the PE greenhouse, the PC greenhouse enabled increased light transmittance and thus a higher indoor temperature during both summer and winter. The thermal insulating property of the PC sheet effectively reduced the heating loss by approximately 55% during winter. The cherry tomatoes grown in the PC greenhouse exhibited superior fruit characteristics in terms of size, weight, and sugar content. The total amount of cherry tomatoes produced per unit area (1,000 ㎡) in the PC greenhouse was found to be greater by approximately 19% compared to that in the PE greenhouse.