• 대한공업교육학회지
• /
• v.35 no.2
• /
• pp.224-237
• /
• 2010

When the underwater structure sails high speed, noise and vibration propagate to the sensor in the nose of the dome. In this paper, to avoid this kind of noise and vibration CRP(Carbon Reinforced Plastic) material and SNORE ring(Self-NOise REduction Ring) are attached at the curved structure and simulates its isolation characteristics using commercial software. Vibration displacement and stress are calculated at the planar sensor array. The material of the curved structure is aluminum and maximum outer diameter is 53Omm, 215mm in length, 270mm in planar diameter, respectively. Based on the simulation results, reduction ratio of the received normal stress at the sensor is above 95% at the frequency of 12kHz and 15kHz. At the mid point of the planar sensor the normal stress is higher than 20mm and 40mm apart. This results can be used to increase the sensitivity of the acoustic sensor as a basic data.

• Journal of Navigation and Port Research
• /
• v.29 no.10 s.106
• /
• pp.871-876
• /
• 2005

Application of semiconductor sensors has been widely spreaded into various industries because those have several merits like easy miniaturization and batch production comparison with previous mechanical sensors. But external conditions such as thermal and repetitive load have a bad effect on sensors's lifetime. Especially, this paper was focused on fatigue life of a interconnect made by various materials. Firstly we implemented the stress analysis for interconnect under thermal load and wording pressure. And the fatigue lifetime of each material was induced by Manson & Coffin Equation using the plastic stress-strain curve obtained by the plastic-elastic Finite Element Analysis. The Fatigue lifetime in its bottom is smaller than others and bending load have not an effect on the fatigue lifetime of the interconnect but the stress distribution.

• Korean Journal of Clinical Pharmacy
• /
• v.21 no.2
• /
• pp.131-137
• /
• 2011

The purpose of this study was to evaluate the clinical efficacy of a standardized special ethanol extract from Gynostemma pentaphyllum as a management for anxiety and stress of normal population. This is a two-arm, parallelgroup, randomized, double blind clinical trial comparing Gynostemma pentaphyllum extract 200 mg bid (GP-EX, n=48) or placebo bid (n=54). The main outcome measures were the decrease in anxiety sensitivity index (ASI), the State version (S-STAI) of the Stait-Trait Anxiety Inventory (STAI) and the Trait version (T-STAT) of the STAI from baseline over a 6 weeks treatment period. In more anxious group (S-STAI50 or ASI19), the anxiety in group with GP-EX was decreased significantly than one in normal population with placebo [S-STAI50: T-STAI = from $57.7{\pm}6.5$ ($mean{\pm}S.D.$) to $46.8{\pm}11.2$ in normal population with GP-EX, p=0.002 vs. from $54.1{\pm}9.9$ to $49.0{\pm}9.6$ in normal population with placebo, p>0.05; ASI19: T-STAI = from $47.2{\pm}12.0$ to $42.4{\pm}11.1$ in normal population with GP-EX, p=0.022 vs. from $48.7{\pm}11.5$ to $46.0{\pm}10.4$ in normal population with placebo, p>0.05]. The most frequently reported adverse reactions considered possibly related to treatment were mild gastrointestinal events. GP-EX is more effective than placebo and is well tolerated as a therapy for anxiety and stress of normal population.

• Journal of Microbiology and Biotechnology
• /
• v.29 no.11
• /
• pp.1806-1816
• /
• 2019

Candida albicans is an opportunistic fungus possessing multiple virulence factors controlling pathogenicity. Cell wall proteins are the most important among these factors, being the first elements contacting the host. Ddr48 is a cell wall protein consisting of 212 amino acids. A DDR48 haploinsufficient mutant strain was previously found necessary for proper oxidative stress response and drug resistance. In this study, we aimed to further elucidate the role of Ddr48 by performing additional phenotypic characterization assays. A combinatory proteomic and bioinformatics approach was also undertaken to determine differentially expressed cell wall proteins. Results showed that the mutant strain exhibited a 10% decrease in adhesion mirrored by a 20% decrease in biofilm formation, and slight sensitivity to menadione, diamide, and SDS. Both strains showed similar hyphae formation, virulence, temperature tolerance, and calcofluor white and Congo red sensitivities. Furthermore, a total of 8 and 10 proteins were identified exclusively in the wild-type strain grown under filamentous and non-filamentous conditions respectively. Results included proteins responsible for superoxide stress resistance (Sod4 and Sod6), adhesion (Als3, Hyr4, Pmt1, and Utr2), biofilm formation (Hsp90, Ece1, Rim9, Ipp1, and Pra1) and cell wall integrity (Utr2 and Pga4). The lack of detection of these proteins in the mutant strain correlates with the observed phenotypes.

• Progress in Superconductivity and Cryogenics
• /
• v.18 no.4
• /
• pp.21-24
• /
• 2016

The mechanical properties of REBCO coated conductor (CC) wires under uniaxial tension are largely determined by the thick component layers in the architecture, namely, the substrate and the stabilizer or even the reinforcement layer. Depending on device applications of the CC tapes, it is necessary to reinforce thin metallic foils externally to one-side or both sides of the CC tapes. Due to the external reinforcement of brass foils, it was found that this could increase the reversible strain limit from the Cu-stabilized CC tapes. In this study, the effects of differently hardened brass foil laminate on the electromechanical property of CC tapes were investigated under uniaxial tension loading. The tensile strain dependence of the critical current ($I_c$) was measured at 77 K and self-field. Depending on whether the $I_c$ of CC tapes were measured during loading or after unloading, a reversible strain (or stress) limit could be determined, respectively. The both-sides of the Cu-stabilized CC tapes were laminated with brass foils with different hardness, namely 1/4H, 1H and EH. From the obtained results, it showed that the yield strength of the brass laminated CC tapes with EH brass foil laminate was comparable to the one of the Cu-stabilized CC tape due to its large yield strength even though its large volume fraction. It was found that the brass foil with different hardness was mainly sensitive on the stress dependence of $I_c$, but not on the strain sensitivity due to the residual strain induced in the laminated CC tapes during unloading.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.6
• /
• pp.435-443
• /
• 2015

Offshore structure may be considerably vulnerable to fatigue failure while initial flaw propagates under cyclic loading, so crack propagation analysis/fracture/yield assessments about initial flaw detected by NDT are necessarily required. In this paper, case studies have been conducted by flaw assessment program using engineering criticality analysis (ECA) approach. Variables such as flaw geometry, flaw size, structure geometry, dynamic stress, static stress, toughness, crack growth rate, stress concentration factor (SCF) affected by weld are considered as analysis conditions. As a result, the safety of structure was examined during fatigue loading life. Also, critical initial flaw size was calculated by sensitivity module in the developed program. The flaw assessments analysis using ECA approach can be very useful in offshore industries owing to the increasing demand on the engineering criticality analysis of potential initial flaws.

• Journal of the Korean Institute of Gas
• /
• v.17 no.2
• /
• pp.50-58
• /
• 2013

Various process piping usually carries out high flammable and explosible gas under high pressure and high temperature. Due to frequent change of design and structure it becomes more complicated and compactly located. The safety management level is relatively low since it is considered as simply designed component. In this study a safety assessment procedure is proposed for complicated piping system around a mixing drum in which natural gas and by-product gases were mixed. According to ASME code, pipe stress analysis was conducted for determining design margin at some key locations of the piping. These high stress locations can be used as major inspection points for managing the pipe integrity. Sensitivity analysis with outside temperature of the pipe and support constraint condition. Possible effect of hydroen gas to the pipe steel during the previous use of the by-product gas was also discussed.

• BMB Reports
• /
• v.41 no.6
• /
• pp.448-454
• /
• 2008

Two full-length cDNAs, PutPMP3-1 and PutPMP3-2, encoding PMP3 family proteins were isolated from Puccinellia tenuiflora, a monocotyledonous halophyte. Expression of both genes was induced by low temperature, salt stress, dehydration, ABA, and $NaHCO_3$. Transcripts of PutPMP3-2 were more strongly induced by these stresses relative to those of PutPMP3-1, particularly under low temperature and dehydration conditions. Expression of PutPMP3-1 and PutPMP3-2 in yeast mutants lacking the PMP3 gene can functionally complement the membrane hyper-polarization and salt sensitivity phenotypes resulting from PMP3 deletion. To compare the functions of PutPMP3-1 and PutPMP3-2, the orthologous genes in rice (OsLti6a and OsLti6b) were isolated. Both OsLti6a and OsLti6b could functionally complement the loss of PMP3 in yeast. PutPMP3-2 and OsLti6a were more effective in reversing membrane hyperpolarization than PutPMP3-1 and OsLti6b. However, the four yeast transformants each showed similar levels of salt tolerance. These results imply that these PMP3 family members don't function identically under different stress tolerance conditions.

• The Journal of Korean Physical Therapy
• /
• v.22 no.6
• /
• pp.65-70
• /
• 2010

Purpose: Exercise has been shown to be a simple and economical therapeutic modality that may be considered as an effective aid for diabetic mellitus. For example, exercise training increases insulin sensitivity in type 2 diabetes. But we found no reported of how exercise affect type 1 diabetes. This study investigated the impact of aerobic and graduated treadmill exercise regimens on body weight, glucose and insulin concentrations, lipid profiles, and oxidative stress indicators in rats with streptozotocin (STZ) induced diabetes. Glycosylated hemoglobin ($HbA_{1c}$) was determined as an indicator of glucose control during exercise. Methods: In our study, a total of 40 rats were used. Three groups of 10 rats each were given STZ to induce diabetes. The remaining 10 rats became the normal group. After 28 days we determined biochemical parameters such as glucose, glycosylated hemoglobin ($HbA_{1c}$), insulin concentration, serum total cholesterol (TC), triglycerides (TG), and high-density lipoprotein (HDL). Superoxide dismutase (SOD) and catalase activities were also measured. Results: Concentrations of blood glucose and $HbA_{1c}$ in the moderated exercise groups were significantly decreased after 28 days compared with the control group (p<0.05). There was a significant reduction in serum TC and TG in the experimental groups. The activity of SOD increased significantly by 17.70% and 48.25% respectively. Conclusion: These results indicate that physical training and exercise training affects body weight, fasting blood glucose, $HbA_{1c}$, insulin, lipid profiles, and antioxidant status in rats with streptozotocin-induced diabetes. We suggest that graduated treadmill exercise may have therapeutic, preventative, and protective effects against diabetes mellitusby improving glycemic control, oxidant defenses, and lipid metabolism.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1331-1337
• /
• 2013

This study deals with the structural optimization of hybrid vertical-axis wind turbine blades using a response surface method (RSM). The structural analysis results suggest that the stress of hybrid vertical-axis wind turbine blades exceeds the yield strength. Optimization techniques are then applied to structural design to ensure a safe structure. First, the design factors that strongly influence the structural response are identified. The RSM was applied based on the design of experiments. The objective function and constraint terms set the weight and allowable stress, respectively. Furthermore, sensitivity analysis was conducted to indicate the effects of the design factors on the stress and weight. Finally, structural design was performed for the hybrid vertical-axis wind turbine blade.