• 한국전기전자재료학회논문지
• /
• 제33권3호
• /
• pp.163-168
• /
• 2020

We studied the change of photovoltaic properties of a flexible CuIn_xGa(_1-x)Se₂ (CIGS) solar cell fabricated on polyimide by mechanical bending with curvature radii of 75 mm (75R) and 20 mm (20R). The flexible CIGS cells were flattened on a PET film, then placed and forced against the surface of a curved block fabricated with pre-designed curvatures. Both up (compressive) and down (tensile) bending were applied to a specimen of CIGS on PET with curvatures of 75R and 20R for 10,000 times and 2,000 times, respectively. From J-V measurements, we found that the conversion efficiency (Eff.) was reduced by 3% and 4% for up-and down-bending, respectively, at curvature 75R; it was greatly reduced by 15% for curvature 20R in the up-bending. However, the open circuit voltage (V_oc) and short-circuit current density (J_sc) seemed to change little, within 3%, for the applied mechanical stresses. The degradation in Eff. resulted from the deterioration of the series (R_s) and shunt (R_sh) resistances of the solar cell.

• Journal of Welding and Joining
• /
• 제25권6호
• /
• pp.59-63
• /
• 2007

The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates and in addition internal and external constraints have much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to butt weld of thin plates to reduce the transverse and longitudinal deformation. In order to investigate the quantitative effect of tensioning method upon the reduction of angular deformation and shrinkage in longitudinal and transverse direction of weld line, butt welding test has been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. From the present experimental study, it has been found that the tensioning method is very effective in reducing the weld-induced residual stress as well as the weld-induced deformation.

• Asian-Australasian Journal of Animal Sciences
• /
• 제33권6호
• /
• pp.913-920
• /
• 2020

Objective: The objective of this experiment was to compare conventional antioxidants and plant extracts for oxidative stress control in lambs fed a high-concentrate diet. Methods: Forty-eight male Dorper×Santa Ines lambs with an initial weight of 20±1.49 kg and 60 days of age, were used to evaluate the effects of feeding a combination of Macleaya cordata and Magnolia officinalis plant extracts (0 vs 320 mg/kg dry matter [DM]) in combination with selenium+vitamin E (0 vs 100 IU/kg DM of vitamin E and 0.1 mg/kg DM of selenium) in a completely randomized block design in a 2×2 factorial arrangement. The animals were housed in individual pens and received a high-concentrate diet consisting of 80% whole corn and 20% protein pellet for 60 days. The animals were weighed at the beginning of the experiment and every 14 days for performance monitoring. Three blood samplings were performed during the experimental period for the evaluation of oxidative and protein parameters. Results: The treatments with vitamin E and selenium as additives had a positive influence on final weight, daily weight gain, carcass weight, and selenium content in longissimus muscle (p = 0.01). Plant extracts tended to improve final weight (p = 0.064) and daily weight gain (p = 0.059), showing similar effect as selenium and vitamin E. There was no effect of treatment on blood proteins, indicating that the animals were healthy throughout the experiment. Conclusion: The use of plant extracts had a similar effect as the addition of selenium and vitamin E, with dietary inclusion of additives resulting in better performance of lambs but both supplements did not have strong influence on oxidative stress.

• 소성∙가공
• /
• 제16권7호
• /
• pp.509-515
• /
• 2007

As the springback of sheet metal during unloading may cause deviation from a desired shape, accurate prediction of springback is essential for the design of sheet stamping operations. When considering the case of a sheet metal being bent to radius $\rho$ that is such that the maximum stress induced exceed the elastic limit of the material, plastic strain in the outer surface will occur and the material will take a permanent set: but since, on removing the bending moment, the recovery of the material is not uniform across the thickness, springback will occur and the radius $\rho$ will not be maintained. Furthermore, when a tensile load being applied to each end of specimen, the tensile stress due to bending is increased and the compressive stress is decreased or cancelled and eventually the whole specimen may be in varying degree of tension. On the removal of the applied load the specimen loses its elastic strain by contracting around the contour of the block, the radius $\rho$ will be determined by the residual differential strain. Therefore in this study the springback is analytically estimated by the residual differential strains between upper and lower surfaces of greatest radius after elastic recovery, and a springback model based on the bending moment is also analytically derived for comparison purpose.

• The Korean Journal of Pain
• /
• 제11권2호
• /
• pp.235-240
• /
• 1998

Background: Preoperative blocking of surgical nociceptive inputs may prevent sensitization of CNS and reduce postoperative pain. The stress responses to surgical trauma consist of increase in catabolic hormones and decrease in anabolic hormones. We studied whether preoperative intravenous morphine could affect postoperative pain and change plasma cortisol and serum glucose levels. Methods: Thirty eight patients undergoing total abdominal hysterectomy were randomly assigned to one of three groups. Control group (n=11) did not received intravenous morphine, preoperative group (n=13) received intravenous morphine (0.1 mg/kg as a bolus 10 min before operation and followed by 1.5 mg/hr for 10 hours), postoperative group (n=14) received the same doses and method of intravenous morphine of preoperative group postoperatively. Postoperative pain relief was provided with i.v. fentanyl through Patient-Controlled-Analgesia Pump. Postoperative visual analogue scores (VAS), analgesic requirement (first request time, total amounts used), side effects, plasma cortisol and serum glucose levels were compared. Results: VAS were different between control group and the other two goups, but were not different between preoperative and postoperative group. Total amounts of used fentanyl were not different among groups, but first request time were significantly delayed in the preoperative group compared with the other two groups ($66.2{\pm}33.9$ vs $39.0{\pm}15.4$ and $45.0{\pm}14.9$ min respectively, p<0.05). Plasma cortisol and serum glucose levels were not different among groups. Conclusions: Above dosage of preoperative and postoperative morphine has analgesic effect, but could not block surgical stress induced plasma cortisol and serum glucose increase.

• Clinical and Experimental Reproductive Medicine
• /
• 제41권3호
• /
• pp.125-131
• /
• 2014

Objective: Under estrogen deficiency, blastocysts cannot initiate implantation and enter dormancy. Dormant blastocysts live longer in utero than normal blastocysts, and autophagy has been suggested as a mechanism underlying the sustained survival of dormant blastocysts during delayed implantation. Autophagy is a cellular degradation pathway and a central component of the integrated stress response. Reactive oxygen species (ROS) are produced within cells during normal metabolism, but their levels increase dramatically under stressful conditions. We investigated whether heightened autophagy in dormant blastocysts is associated with the increased oxidative stress under the unfavorable condition of delayed implantation. Methods: To visualize ROS production, day 8 (short-term dormancy) and day 20 (long-term dormancy) dormant blastocysts were loaded with $1-{\mu}M$ 5-(and-6)-chloromethyl-2', 7'-dichlorodihydrofluorescein diacetate, acetyl ester (CM-$H_2DCFDA$). To block autophagic activation, 3-methyladenine (3-MA) and wortmannin were used in vivo and in vitro, respectively. Results: We observed that ROS production was not significantly affected by the status of dormancy; in other words, both dormant and activated blastocysts showed high levels of ROS. However, ROS production was higher in the dormant blastocysts of the long-term dormancy group than in those of the short-term group. The addition of wortmannin to dormant blastocysts in vitro and 3-MA injection in vivo significantly increased ROS production in the short-term dormant blastocysts. In the long-term dormant blastocysts, ROS levels were not significantly affected by the treatment of the autophagy inhibitor. Conclusion: During delayed implantation, heightened autophagy in dormant blastocysts may be operative as a potential mechanism to reduce oxidative stress. Further, ROS may be one of the potential causes of compromised developmental competence of long-term dormant blastocysts after implantation.

• 한국지반공학회지:지반
• /
• 제11권1호
• /
• pp.41-50
• /
• 1995

자연상태의 점성토는 Ko상태로 존재하며 하중재하시 주웅력방향에 따라 다르게 거동하는 이방적 특성을 갖는다. 그러나 실험실에서 점성토의 강도특성을 파악하기 위하여 실시하고 있는 실험은 실용성과 간편성 때문에 등방압밀 삼축시험이 보편적으로 사용되고 있다. 이 연구에서는 정규압밀점성토의 이방적 특성과 압밀방법에 따른 전단특성을 고찰하기 위하여 토괴의 형태로 채취한 불교란 점성토를 등방압밀 또는 Ko압밀시켜 정규압밀상태에 도달하게 한 후 비배수삼축압축과 신장시험을 실시하였다. 시험결과 주응력방향에 따른 강도의 이방성을 작인하였다. 등방압 밀은 압밀시 시료에 가해지는 Ko상태보다 높은 평균주응력과 흙의 이방적 구조의 파괴때문에 비 배수강도를 과대평가하며 이방성이 감소하고 응력-변형률과 발생 과잉간극수압이 영향을 받음을 알 수 있었으며, 과압밀점성토의 경우 과압밀비를 감소시킨다. 또한 내부마찰각은 신장시험이 압축시험보다 큰 값을 나타내지만 파괴시의 응력상태를 이용하여 회귀분석한 결과에 따르면 신장시 점착력과 함께 나타나는 내부마찰각은 압축시험과 거의 같은 값을 가짐을 알 수 있었다.

• Journal of Crop Science and Biotechnology
• /
• 제11권4호
• /
• pp.249-256
• /
• 2008

The objective of this work was to evaluate the germination of 12 rice genotypes under propionic acid stress, a phytotoxic compound produced in low drainage soils with high organic matter content. The tests were conducted with the first count of germination (PCG) and germination (G) of the genotypes subjective to 0, 3, 6, and 9 mM propionic acid concentrations. The seeds of each genotype were placed in germitest paper pre-soaked in treatment solutions forming individual bags. The germination was performed at $25^{\circ}C$ and the counts were carried out at 7 (PCG) and 14 days (G). A factorial random block design was performed with four replications of 50 seeds per genotype. Our study revealed that doses up to 9 mM propionic acid in the pre-soaking solution were efficient for genetic variability studies involving the character germination in rice; genetic variability for germination was detected in the collection of rice genotypes when subjected to propionic acid toxic effects. The genotypes Guichow, Dawn, and Toride-1 showed germination stability when subjected to increasing levels of propionic acid, and genotypes originated from irrigated system-cultivation performed better when subjected to propionic acid stress. These three genotypes will be a good biological material to for enhance the resistance to phytotoxic compounds in rice.

• 한국표면공학회지
• /
• 제53권6호
• /
• pp.293-299
• /
• 2020

The characteristics of the polycarbosilane (PCS)-based composite ceramic layer was studied by controlling the curing temperature. The stress at the interface of the graphite and SiOC composite layer was evaluated v ia finite element analysis. As a result, the tensile stress was released as the carbon ratio of the SiC decreases. In experiment, the SiOC layers were coated on the VDR graphite block by dip-coating process. It was revealed that the composition of Si and C was effectively adjusted depending on the curing temperature. As the solution-based process is employed, the surface roughness was reduced for the appropriate PCS curing temperature. Hence, it is expected that the cured SiOC layer can be utilized to reduce cracking and peeling of SiC ceramic composites on graphite mold by improving the interfacial stress and surface roughness.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제31권3호
• /
• pp.248-254
• /
• 2005

The purpose of this study was to investigate the distribution of stress within the regenerated bone surrounding the implant using three dimensional finite element stress analysis method. Using ANSYS software revision 6.0 (IronCAD LLC, USA), a program was written to generate a model simulating a cylindrical block section of the mandible 20 mm in height and 10 mm in diameter. The $5.0{\times}11.5-mm$ screw implant (3i, USA) was used for this study, and was assumed to be 100% osseointegrated. And it was restored with gold crown with resin filling at the central fossa area. The implant was surrounded by the regenerated type IV bone, with 4 mm in width and 7 mm apical to the platform of implant in length. And the regenerated bone was surrounded by type I, type II, and type III bone, respectively. The present study used a fine grid model incorporating elements between 250,820 and 352,494 and nodal points between 47,978 and 67,471. A load of 200N was applied at the 3 points on occlusal surfaces of the restoration, the central fossa, outside point of the central fossa with resin filling into screw hole, and the functional cusp, at a 0 degree angle to the vertical axis of the implant, respectively. The results were as follows: 1. The stress distribution in the regenerated bone-implant interface was highly dependent on both the density of the native bone surrounding the regenerated bone and the loading point. 2. A load of 200N at the buccal cusp produced 5-fold increase in the stress concentration at the neck of the implant and apex of regenerated bone irrespective of surrounding bone density compared to a load of 200N at the central fossa. 3. It was found that stress was more homogeneously distributed along the side of implant when the implant was surrounded by both regenerated bone and native type III bone. In summary, these data indicate that concentration of stress on the implant-regenerated bone interface depends on both the native bone quality surrounding the regenerated bone adjacent to implant and the load direction applied on the prosthesis.