• 공업화학
• /
• 제3권1호
• /
• pp.46-52
• /
• 1992

$TiCl_4-HCl$ 혼합용액으로부터 침전법으로 $TiO_2$를 만들고 이를 황산으로 개질하여 $TiO_2/SO_4{^{2-}}$ 촉매를 제조하였으며 제조된 촉매의 특성을 IR, XPS, XRD 및 DT-TGA로 조사하였다. 개질된 촉매의 산의 세기는 적어도 $H_0{\leq}-14.52$로 초강산 성질을 나타내었으며 이 성질은 $TiO_2$와 황산이온에 의하여 형성된 착물의 S=O 결합성질에 기인하였다. $TiO_2/SO_4{^{2-}}$의 IR spectra를 조사한 결과 황산이온은 $TiO_2$ 표면에 2자리 ligand로 배위하였다. $TiO_2/SO_4{^{2-}}$는 황산으로 개질하지 아니한 순수한 $TiO_2$에 비하여 표면적이 상당히 컸으며 또한 무정형에서 anatase상으로 되는 전이온도도 높았다.

• 한국재료학회지
• /
• 제12권2호
• /
• pp.129-134
• /
• 2002

The optimum condition for fabricating cordierite disc type filter element was deduced. Cordierite monolith was used as starting material for filter element because it has many advantages such as high thermal shock resistance and good catalytic activity compared with $TiO_2$and SiC. The contents of organic additives and foaming agent were optimized to control the porosity and mechanical strength of cordierite filter. Among the required properties to be adopted as filter elements, the pressure drop and NOx removal efficiency were investigated depending on processing variables. It was found that pressure drop depends on particle size distribution of cordierite monolith and organic additives added as forming agent. The pressure drop at 5cm/sec of face velocity was in the range of 15~655mm$H_2O$ at room temperature. The NOx removal efficiency of catalytic filter with $V_2O_5$ as catalyst was over 85% at $450^{\circ}C$.

• 한국수소및신에너지학회논문집
• /
• 제27권3호
• /
• pp.270-275
• /
• 2016

A simple solid state incorporation method was employed in order to incorporate Pd nanocatalyst into a Nafion film for polymer electrolyte membrane fuel cell (PEMFC) via the reduction of palladium (II) bis (acetylacetonate), $Pd(acac)_2$. It was sublimed, penetrated into Nafion film and then reduced to Pd nanoparticles simultaneously in a glass reactor of N2 atmosphere at $180^{\circ}C$ for 1, 3 and 5 min. This reaction was took place without any reducing agent and any solvent. The morphology of the Pd nanoparticles was observed by transmission electron microscopy (TEM), and Pd distribution was analyzed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). And 23% modification of tensile strength of Pd/Nafion composite film was measured by universal testing machine and I-V curve was estimated by using a unit cell with $5{\times}5cm^2$ active area.

• Elastomers and Composites
• /
• 제35권3호
• /
• pp.205-214
• /
• 2000

TDI에 PPG 3000을 기재로 사용하고 PPG 400, PPG 1000, PPG 2000을 $0{\sim}50%$ 혼합 사용하여 프리폴리머형 폴리우레탄수지를 합성한 후 합성 내용을 분석하고 합성물의 물성을 조사하였다. 반응은 촉매를 합성 초기에 넣었을 때에는 글리콜이 TDI 적하시에 대부분 반응되어 점도의 급상승이 일어나 불안하였지만 $40^{\circ}C$에서 무촉매 상태로 TDI를 적하시킨 후 $60^{\circ}C$ 승온 후에 촉매를 넣었을 때에는 매우 안정하였다. 인산을 사용하면 $40^{\circ}C$에서 부반응이 억제되어 점도는 낮아지지만 경화반응시 입체적으로 가교되지 못해 가교속도는 느리게 나타났다. 경화속도는 NCO/OH의 비보다는 분자의 입체적 구조에 더 영향을 받았다. 접착력은 글리콜 성분 중에 PPG 400을 적어도 30%(wt.%) 이상 사용하였을 때 PPG 400에 의한 가교밀도 상승으로 보다 우수한 물성을 나타내었다.

• 한국염색가공학회지
• /
• 제33권4호
• /
• pp.238-249
• /
• 2021

In this study, the effect on flame retardancy and various physical properties when TiO₂ was added with a citric acid/phosphate complex acid catalyst together with Pyrovatex CP new (N-methylol dimethylphosphonopropionamide), a phosphorus-based flame retardant, was studied on cotton fibers. SEM-EDS analysis was performed to confirm the surface characteristics and surface element analysis of the flame-retardant treated cotton fibers, and a vertical carbonization test was performed to confirm the char formation capability and flame retardancy according to the phosphoric acid ratio. By comparing the LOI index before and after washing 10 times, the washing durability of the flame retardant solution containing the phosphoric acid catalyst and TiO₂ was tested by LOI index after ten washing cycles. In addition, the influence of the flame-retardant processing on the physical properties were compared including thermogravimetric analysis (TGA), tear strength and whiteness.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.729-732
• /
• 2008

최근 실내공기질에 대한 관심이 집중되고 있는 가운데 이를 개선하고자 하는 노력이 다각도로 진행되고 있다. 본 연구는 기존의 친환경 마감재 적용 기술과 달리 콘크리트 자체에 활성탄과 흡착된 오염 공기를 분해할 수 있도록 기능성 촉매를 혼입함으로써 기본적인 물성과 포름알데히드 제거율을 시험하여 공기정화 효과를 분석하고자 하였다. 실험 결과 활성탄의 첨가량 증가에 따라 슬럼프는 감소하는 경향을 나타내었고, 압축강도는 큰 차이 없이 유사한 것으로 나타났다. 공기질 개선과 관련하여 포름알데히드 제거율을 시험한 결과 최대 80%까지 제거하는 것으로 나타났다.

• Carbon letters
• /
• 제5권4호
• /
• pp.159-163
• /
• 2004

The polymer-ceramic hybrid, known as 'ceramer', was synthesized by a sol-gel process by incorporating different amount of alkoxide as source of silicon in resorcinol-formaldehyde in presence of basic catalyst to get different percentage of silicon in ultimate carbonized composites. FTIR of the ceramer confirms that it is a network of Si-O-Si, Si-O-$CH_2$ and Si-OH type groups linked with benzene ring. Different amount of silicon in the ceramer exhibits varying temperature of thermal stability and lower coefficient of thermal expansion as compared to pure resorcinol-formaldehyde resin. The lower value of CTE in ceramer is due to existence of silica and resorcinol -formaldehyde in co-continuous phase. Unidirectional composites prepared with ceramer matrix and high-strength carbon fibers show lower value of flexural strength at polymer stage as compared to those prepared with resorcinol-formaldehyde resin. However, after heat treatment to $1450^{\circ}C$, the ceramer matrix composites show large improvement in the mechanical properties, i.e. with 7% silicon in the ceramer, the flexural strength is enhanced by 100% and flexural modulus value by 40% as compared to that of pure resorcinol-formaldehyde resin matrix composites.

• 한국세라믹학회지
• /
• 제44권10호
• /
• pp.574-579
• /
• 2007

Porous $Al_2O_3$ ceramics were prepared by the gelcasting foams method (a slurry foaming process) with acrylamide monomer. The foaming and gelation behavior was investigated with the parameters such as the type and concentration of surfactant, solid loading of slurry, and the concentrations of initiator and catalyst. Density, porosity, microstructure, and strength of the green and sintered samples were characterized. Of the four kinds of surfactants tested, Triton X-114 showed the highest foaming ability for the solid loading of 55-30 vol%. The gelation condition giving the idle time off min was found to set the foamed structure without significant bubble enlargement and liquid lamella thinning. The green samples were fairly strong and machinable and showed maximum strength of 2.4 MPa in diametral compression. The sintered samples showed densities of 10-36% theoretical (i.e. porosity 90-64%) with a highly interconnected network of spherical pores with sizes ranging from 30 to $600{\mu}m$. The pore size and connectivity increased but the cell strut thickness decreased with decreasing the solid loading. Flexural strength of 37.8-1.7 MPa was obtained for the sintered samples.

• Transactions on Electrical and Electronic Materials
• /
• 제7권6호
• /
• pp.283-292
• /
• 2006

So that high-strength and electrical properties apply by excellent high voltage insulator electricity material, ATH content and platinum-based flame retardant that influence in flame retardant and tracking characteristic among composite of silicone rubber studied mechanical strength and influence getting to electrical properties. Composition of ${\alpha}$, ${\omega}-vinyl$ poly (dimethyl-methylphenyl) siloxane(VPMPS) of a polymer quantity made doing mole of D4, $D3^{Me,Ph}$ and VMS by 1000:15:0.2 mole ratio and uses basic catalyst tetramethylammonium silanolate(TMAS) and do opening equilibrium polymerization to be used to main polymer for high voltage insulation insulator. Control ATH content and content of platinum-based flame retardant and made high voltage insulation silicone rubber. Measured mechanical strength of making silicone rubber using UTM, and tracking characteristic according to standard of IEC 60587, flame retardant test studied effect that flame retardant characteristic gets in tracking characteristic, measuring according to UL94V method of test.

• 방사선산업학회지
• /
• 제4권1호
• /
• pp.19-23
• /
• 2010

Vinyl ester (VE) resins, introduced in the late 1960s, have made large strides in reinforced plastics applications as adhesive and matrix materials on their appropriate mechanical performance characteristics in the glassy state. Generally, VE resins are a group of dimethacrylate resins based on bisphenol A type epoxy resin. They exhibit easy handling properties as well as good resistance to most chemical agents due to their mechanical and thermal properties. In this study, the effects of curing methods of vinyl ester resins on gel contents, flexural strength and dynamic mechanical properties were investigated. Thermal curing (room temperature, $80^{\circ}C$) and electron beam curing were used to crosslink a VE resin/styrene complex (65/35 wt%) with methyl ethyl ketone peroxide (MEKPO) as a catalyst and an 8 wt% cobalt naphthenate in styrene solution as a accelerator. For the samples, gel contents as well as flexural strength and dynamic mechanical properties were characterized and compared by soxhlet apparatus, universal testing machine (UTM) and dynamic mechanical analysis (DMA). As a result, the electron-cured VE resin was confirmed as a better condition than those for gel contents, flexural strength and dynamic mechanical properties, respectively.