• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.17 no.2
• /
• pp.183-202
• /
• 2019

For design and performance assessment of a high-level radioactive waste (HLW) disposal system, it is necessary to understand the characteristics of coupled thermo-hydro-mechanical (THM) behavior. However, in previous studies for the Korean Reference HLW Disposal System (KRS), thermal analysis was performed to determine the spacing of disposal tunnels and interval of disposition holes without consideration of the coupled THM behavior. Therefore, in this study, TOUGH2-MP/FLAC3D is used to conduct THM modeling for performance assessment of the Korean Reference HLW Disposal System (KRS). The peak temperature remains below the temperature limit of $100^{\circ}C$ for the whole period. A rapid rise of temperature caused by decay heat occurs in the early years, and then temperature begins to decrease as decay heat from the waste decreases. The peak temperature at the bentonite buffer is around $96.2^{\circ}C$ after about 3 years, and peak temperature at the rockmass is $68.2^{\circ}C$ after about 17 years. Saturation of the bentonite block near the canister decreases in the early stage, because water evaporation occurs owing to temperature increase. Then, saturation of the bentonite buffer and backfill increases because of water intake from the rockmass, and bentonite buffer and backfill are fully saturated after about 266 years. The stress is calculated to investigate the effect of thermal stress and swelling pressure on the mechanical behavior of the rockmass. The calculated stress is compared to a spalling criterion and the Mohr-Coulumb criterion for investigation of potential failure. The stress at the rockmass remains below the spalling strength and Mohr-Coulumb criterion for the whole period. The methodology of using the TOUGH2-MP/FLAC3D simulator can be applied to predict the long-term behavior of the KRS under various conditions; these methods will be useful for the design and performance assessment of alternative concepts such as multi-layer and multi-canister concepts for geological spent fuel repositories.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.6
• /
• pp.577-587
• /
• 2021

Room and Pillar method is an underground facility construction method that maximizes the strength of the in-situ ground. In order to secure the safety of the underground space, it is necessary to secure the safety of the room actually used in addition to the safety of pillar of the room and Pillar method. In this study, the evaluation method for the safety of the room and rock pillar in the room and pillar method was studied through numerical analysis. Numerical analysis was performed for a total of 125 cases using ground conditions, pillar width, and room width as parameters, and the results were derived. As for the safety factor of the pillar, it was confirmed that the safety factor increased when the strength of the ground increased, and it was confirmed that the increment in the safety factor decreased when the width of the pillar was widened. The room strain was evaluated by applying the Critical strain. As the width of the pillar became narrower, the Critical strain was higher, and as the width of the room became smaller, the Critical strain was smaller. As a result of the correlation analysis between the safety factor of the pillar and the room strain, it was possible to derive the upper limit of the room strain that can secure the standard safety factor of the pillar according to the width of the pillar. It is judged that the results derived from this study can be used as a guideline to secure the safety of the room when the actual design is performed in consideration of the ground conditions and room width.

• Journal of Korea Foresty Energy
• /
• v.21 no.2
• /
• pp.25-33
• /
• 2002

One of the critical problems to preserve books and documents in libraries and archives is the deterioration. Some of previous results showed that the major cause of paper deterioration was the acid-catalyzed hydrolysis of the cellulose in paper fibres and aging rate of acidic paper was faster than that of alkaline paper. Therefore, It is necessary to remove the acid in the paper for reducing the rate of paper deterioration. It has been reported to extend the useful life of acidic paper by three to five times. Recently, It has been recognized the need for an effective method of deacidifying large quantities of books and document. However, in the previous many reports little attention was paid to the effect of paper additives. In this paper, We carried out experiment about the effect of additives on paper aging and the effect of deacidification by the gaseous ethanolamines (monoehtanolamine, diethanolamine, triehtanolamine). In result, it was found that the strength of aging was in the order of the alum＋rosin＞alum ＞AKD＞ control and the rate of deacidification was in the order of the monoethanolamine＞diethanolamine＞triethanolamine. The treatment with the gaseous ethanolamines caused decreasing of brightness and dropping of fold endurances. However, deacidification by combination treatment of the various gaseous ehtnaolamines prevented from decreasing of brightness and dropping of folding endurances.

• Journal of Food Hygiene and Safety
• /
• v.33 no.4
• /
• pp.296-305
• /
• 2018

Spiroxamine, one of fungicides, is used to control powdery mildew in various crops and black yellow sigatoka in bananas. The major strength of spiroxamine is to control powdery mildew in various crops and bananas yellow sigatoka in bananas. The compound has shown a high level of activity, good persistence and crop tolerance. Besides powdery mildew, good control of rust, net blotch and Rhynchosporium diseases been indicated in cereals, together with a complementary activity against Septoria diseases. In 2017, the maximum residue limit (MRL) of spiroxamine established in Korea. According to Ministry of ood and rug afety) regulations, spiroxamine residues defined only parent compound. Thus, a analytical method is needed to estimate the residue level of the parent compound. The objective of this study was to develop and validate analytical method for spiroxamine in representative agricultural commodities. Samples were extracted with acetonitrile and partitioned with dichloromethane to remove the interfering substances. The analyte were quantified and confirmed liquid chromatograph-tandem mass spectrometer (LC-MS/MS) in positive-ion mode using multiple reaction monitoring (MRM). Matrix matched calibration curves were linear over the calibration ranges ($0.0005{\sim}0.1{\mu}g/mL$) for the analyte in blank extract with coefficient of determination ($r^2$) > 0.99. For validation purposes, recovery studies will be carried out at three different concentration levels (LOQ, 10LOQ, and 50LOQ) performing five replicates at each level. The recoveries 70.6~104.6% with relative standard deviations (RSDs) less than 10%. All values were consistent with the criteria ranges in the Codex guidelines (CAC/GL40, 2003) and MFDS guidelines. proposed analytical method be used as an official analytical method in the Republic of Korea.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.1
• /
• pp.103-113
• /
• 2020

Jack-up drilling rigs are widely used in the offshore oil and gas exploration industry. Although originally designed for use in shallow waters, trends in the energy industry have led to a growing demand for their use in deep sea and harsh environmental conditions. To extend the operating range of jack-up units, their design must be based on reliable analysis while eliminating excessive conservatism. In current industrial practice, jack-up drilling rigs are designed using the working(or allowable) stress design (WSD) method. Recently, classifications have been developed for specific regulations based on the load and resistance factor design (LRFD) method, which emphasises the reliability of the methods. This statistical method utilises the concept of limit state design and uses factored loads and resistance factors to account for uncertainly in the loads and computed strength of the leg components in a jack-up drilling rig. The key differences between the LRFD method and the WSD method must be identified to enable appropriate use of the LRFD method for designing jack-up rigs. Therefore, the aim of this study is to compare and quantitatively investigate the differences between actual jack-up lattice leg structures, which are designed by the WSD and LRFD methods, and subject to different environmental load-to-dead-load ratios, thereby delineating the load-to-capacity ratios of rigs designed using theses methods under these different enviromental conditions. The comparative results are significantly advantageous in the leg design of jack-up rigs, and determine that the jack-up rigs designed using the WSD and LRFD methods with UC values differ by approximately 31 % with respect to the API-RP code basis. It can be observed that the LRFD design method is more advantageous to structure optimization compared to the WSD method.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.6
• /
• pp.718-724
• /
• 1999

This study was investigated the changes of the properties of matter such as the gel formation of the combined fish based on the mixed rate between the ocean jumbo squid and Alaska pollock surimi, and compared the relationships between the gel formation and water holding capacity. The changes of the gel formation based on 20 min fish grinding time and $2.5\%$ salt concentration according to the mixed rate was thought as the optimal addition limit. There was no significant function of gel product more than $20\%$ Jumbo squid meat. The more squid meat in the mixed meat could make the lower breaking stress but 7:3 rate of pollock : squid could retain breaking strain. The effect of the moisture content on mixed fish meat was studied and the drastic decrease of the gel formation and water holding capacity was indicated in $78\%$.

• Journal of Life Science
• /
• v.26 no.10
• /
• pp.1169-1181
• /
• 2016

The purpose of this study was to investigate the effects of the regular Upright Body Type Excercise on posture, muscle strength of leg, lung capacity and depression of people with mental illness. The subjects of this study were recruited from B mental health center (5 years and more mental illness patients, n=19) located in P city. For the exercise group, They were carried out the Upright Body Type Excercise Program during 8 weeks (60 min/time, 3 times/week). They were randomly divided into two groups. Exercise group (n=10) and Control group (n=9). And also, they were agreed with consent forms before the experiments. Research results were as follows. Through the upper body type exercise, there was significantly difference in PEF and FEV1/FVC in the trained group. And also, there was much improved in depression level in the trained group. The change of melancholy feeling before and after the program was not statistically significant. However, because of limitations of sampling size due to the peculiarities of the program participants, in consideration of the limit of statistical validation exists clearly, intended to better understand the subjective experience of attendees, qualitative analyzing(qualitative research) was carried out in parallel. It was conducted a deep interview only person accepted among program participants, thematic analysis, subject analysis tasks to be subdivided by classifying by considering the semantic units of what participants expressed, was thus carried out. It found that the degree of melancholy feeling of mental disorders who participated in the Upright Body Typed Exercise Program was reduced. The course of the experience of change in depression appered the three subjects and six sub-themes such as "the start of the change", "interest of the program", "recognition of the need of the body’s health", "physical health promotion", "recovery of physical function", "negative change of habits (attitude)", "reduction of sense of depression", "confidence that it is possible to", "hope for the future". Therefore, upper body type exercise is much helpful in lung capacity and mental health of people with mental illness. So, this type of exercise mostly needed in the people with mental illness group than the other group for the quality of life.

• Journal of architectural history
• /
• v.1 no.1 s.1
• /
• pp.68-87
• /
• 1992

This study is the conditions of location according to formed the times in the clan village. The results of this study are as follows ; 1. in the 15th century, the characterestics of the village established residencial place where mountain stream flowed surrounded by the mountain and deep in the mountains with superior quality land. That's because Sa-dae-bu put equal importance on beautiful scenery and practical benefit for living. Stream House provided economical foundation for Sa-dae-bu to be able to keep confucial manners by putting limit their economic status to small medium sized land owner. Topographical condition such as valley or hollow separated from the exterior maintained unification of consanguineous village in self sufficient farming society and held on to independent territory against external to be able to stay away from turbulent days so that they formed residential area of Sa-dae-bu clan. And the valley where flowed clean water was considered as the connection of continuous place where distinctiveness of form in each curve and and factor of calm and dynamic scenery of the clean stream. Scholars in the middle of Chosun Dynasty located in the utopia as place for confucious retirement to study, a place for refinement by combination with the nature or as a way of spacial practice based on Confucious view of nature. 2. in the 16th-l7th century, Most of existing consanguineous villages adopt deep in the mountains for refuge. at that place, upward rank was established by settlement of the ancestor who entered in the village first, the principal was placed in the center of the village and since descendants became numerous, it was serialized as the space of descendants. So, it was arranged in the order of social rank. Most of the villages showed development step by step started from precaution by apperance of the mountain to the lower part. It's because the topography of valley around the village worked as the natural hedge against external force and genealogy of the clan, regularity of social status, order of entrance into the village were reflected into residencial destribution. Also, order of the rank coincided with the one of aspects on geomancy. Genealogical rank within the village represented spacial rank. Houses of descendants and branch families were placed lower than the principal which showed worship to the principal. 3. In 18th century after, as the village was settled nearby cultivated land considering economical loss caused by long distance between residencial area and cultivated land, direction of sect followed by development of village expanded from the front part of the village to the rear part. The principal that was poped out to the front presented frontage over exterior. Therefore, residencial area of branch families expanded to the rear starting from the principal. This represented a slice of social structure at that time. after 18th century, spirit was percieved superior over material, After then, development of cultivation and expantion of land created difference of economic strength within one village. In order to maintain and show off the status of Yang-ban, economic power of indigenous land owner became fundamental, so, sense to worship and to keep the principal became weak eventually. Taking advantage of that situation, residencial area of branch family expanded to the rear part of the principal which showed dual disposition conflicted with each other. However, these clan rules were destroyed and new rules were created after 18th century because of the situation and consciousness at that time.

• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.185-193
• /
• 2015

Ultra high performance concrete (UHPC) has been developed to overcome the low tensile strengths and brittleness of conventional concrete. Considering that UHPC, owing to its composition and the use of steel fibers, develops a compressive strength of 180 MPa as well as high stiffness, the top flange of the steel girder may be superfluous in the composite beam combining a slab made of UHPC and the steel girder. In such composite beam, the steel girder takes the form of an inverted-T shaped structure without top flange in which the studs needed for the composition of the steel girder with the UHPC slab are disposed in the web of the steel girder. This study investigates experimentally and analytically the flexural behavior of this new type of composite beam to propose details like stud spacing and slab thickness for further design recommendations. To that goal, eight composite beams with varying stud spacing and slab thickness were fabricated and tested. The test results indicated that stud spacing running from 100 mm to 2 to 3 times the slab thickness can be recommended. In view of the relative characteristic slip limit of Eurocode-4, the results showed that the composite beam developed ductile behavior. Moreover, except for the members with thin slab and large stud spacing, most of the specimens exhibited results different to those predicted by AASHTO LRFD and Eurocode-4 because of the high performance developed by UHPC.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2003.04a
• /
• pp.61-62
• /
• 2003

Clonal propagation of high-value forest trees through somatic embryogenesis (SE) has the potential to rapidly capture the benefits of breeding or genetic engineering programs and to improve raw material uniformity and quality. A major barrier to the commercialization of this technology is the low quality of the resulting embryos. Several factors limit commercialization of SE for Corsican pine, including low initiation rates, low culture survival, culture decline causing low or no embryo production, and inability of somatic embryos to fully mature, resulting in low germination and reduced vigour of somatic seedlings. The objective was to develop a Corsican pine maturation medium that would produce cotyledonary embryos capable of germination. Treatments were arranged in a completely randomized design. Data were analyzed by analysis of variance, and significant differences between treatments determined by multiple range test at P=0.05. Corsican pine (Pinus nigra var. maritima) cultures were initiated on modified !P6 medium. Modifications of the same media were used for culture multiplication and maintenance. Embryogenic cultures were maintained on the same medium semi solidified with 2.5 g/l Gelrite. A maturation medium, capable of promoting the development of Corsican pine somatic embryos that can germinate, is a combination of iP6 modified salts, 2% maltose, 13% polyethylene glycol (PEG), 5 mg!l abscisic acid (ABA), and 2.5 g/l Gelrite. After initiation and once enough tissue developed they were grown in liquid medium. Embryogenic cell suspensions were established by adding 0.951.05 g of 10- to 14-day-old semisolid-grown embryogenic tissue to 9 ml of liquid maintenance media in a 250ml Erlenmeyer flask. Cultures were then incubated in the dark at 2022$^{\circ}$C and rotated at 120 rpm. After 2.53 months on maturation medium, somatic embryos were selected that exhibited normal embryo shape. Ten embryos were placed horizontally on 20 ml of either germination medium ($\frac{2}{1}$strength Murashige and Skoog (1962) salts with 2.5 g/l activated charcoal) or same medium with copper sulphate adjusted to 0.25 mg/1 to compensate for copper adsorption by activated carbon. 2% and 4% maltose was substituted by 7.5% and 13% PEG respectively to improve the yield of the embryos. Substitution of' maltose with PEG was clearly beneficial to embryo development. When 2% of the maltose was replaced with 7.5% PEG, many embryos developed to large bullet-shaped embryos. At latter stages of development most embryos callused and stopped development. A few short, barrel-shaped cotyledonary embryos formed that were covered by callus on the sides and base. When 4% of the maltose was removed and substituted with 13% PEG, the embryos developed further, emerging from the callus and increasing yield slightly. Microscopic examination of the cultures showed differing morphologies, varying from mostly single cells or clumps to well-formed somatic embryos that resembled early zygotic embryos only liquid cultures with organized early-stag. A procedure for converting and acclimating germinants to growth in soil and greenhouse conditions is also tested. Seedling conversion and growth were highly related to the quality of the germinant at the time of planting. Germinants with larger shoots, longer, straighter hypocotyls and longer roots performed best. When mature zygotic embryos germinate the root emerges, before or coincident with the shoot. In contrast, somatic embryos germinate in reverse sequence, with the cotyledons greening first, then shoot emergence and then, much later, if at all, the appearance of the root. Somatic seedlings, produced from the maturation medium, showed 100% survival when planted in a field setting. Somatic seedlings showed normal yearly growth relative to standard seedlings from natural seed.