• 전기학회논문지
• /
• 제66권12호
• /
• pp.1815-1820
• /
• 2017

In this paper, a study was conducted to estimate the maximum muscle strength which is a standard for selecting exercise intensity in weight training. We designed a device that estimates the muscle fatigue from the EMG signal, expecting to show a correlation between peak muscle strength and fatigue. Curl - Dumbbell was performed using a 4 kg dumbbell and the frequency change of the EMG was observed. At this time, the designed device acquires the signal using the MCU and finally Matlab was used to confirm the change in the center frequency value. The results of 10 subjects were analyzed using SPSS regression analysis. The statistical results showed a correlation of $R^2$ 0.583 and Significant probability of 0.010, and the relation of Y = 8.144-2.097 (slope (MDF)) was obtained. In conclusion, if the wearable device is manufactured in the form of a wearable device and the user can recommend the exercise intensity, the system will be able to retry the more efficient exercise.

• Earthquakes and Structures
• /
• 제21권5호
• /
• pp.477-487
• /
• 2021

This study focuses on the influence of strong ground motion duration on the response and collapse probability of reinforced concrete walls with a predominant response in flexure. Walls with different height and mass were used to account for a broad spectrum of configurations and fundamental periods. The walls were designed following the specifications of the Chilean design code. Non-linear models of the reinforced concrete walls using a distributed plasticity approach were performed in OpenSees and calibrated with experimental data. Special attention was put on modeling strength and stiffness degradation. The effect of duration was isolated using spectrally equivalent ground motions of long and short duration. In order to assess the behavior of the RC shear walls, incremental dynamic analyses (IDA) were performed, and fragility curves were obtained using cumulative and non-cumulative engineering demand parameters. The spectral acceleration at the fundamental period of the wall was used as the intensity measure (IM) for the IDAs. The results show that the long duration ground motion set decreases the average collapse capacity in walls of medium and long periods compared to the results using the short duration set. Also, it was found that a lower median intensity is required to achieve moderate damage states in the same medium and long period wall models. Finally, strength and stiffness degradation are important modelling parameters and if they are not included, the damage in reinforced concrete walls may be greatly underestimated.

• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1890-1899
• /
• 1992

본 연구에서는 이종재료간의 Ⅴ-노치균열의 노치각도 및 재료의 종류에 따른 응력특이성지수와 응력강도 계수 해석에 각각 뉴톤-랍슨법(newtonraphson method), 뉴톤-랍슨법과 최소자승법을 이용한 선점법(collocation method)인 수치해석적 방법을 응용하고, 광탄성 등색선 무늬를 컴퓨터 그래픽하여 응력특이성지수와 응력강도계수가 모우드(mode)에 미치는 특성과 경계요소법(boundary element method)으로 응력해석한 결과로써 선점법을 이용하여 응력강도계수를 해석하고 기존의 결과등과 비교, 검토하 고자 한다.

• Journal of the Korean Physical Society
• /
• 제73권10호
• /
• pp.1577-1583
• /
• 2018

Tumor-treating fields therapy involves placing pads onto the patient's skin to create a low- intensity (1 - 3 V/cm), intermediate frequency (100 - 300 kHz), alternating electric field to treat cancerous tumors. This new treatment modality has been approved by the Food and Drug Administration in the USA to treat patients with both newly diagnosed and recurrent glioblastoma. To deliver the prescribed electric field intensity to the tumor while minimizing exposure of organs at risk, we developed an optimization method for the electric field distribution in the body and compared the electric field distribution in the body before and after application of this optimization algorithm. To determine the electric field distribution in the body before optimization, we applied the same electric potential to all pairs of electric pads located on opposite sides of models. We subsequently adjusted the intensity of the electric field to each pair of pads to optimize the electric field distribution in the body, resulting in the prescribed electric field intensity to the tumor while minimizing electric fields at organs at risk. A comparison of the electric field distribution within the body before and after optimization showed that application of the optimization algorithm delivered a therapeutically effective electric field to the tumor while minimizing the average and the maximum field strength applied to organs at risk. Use of this optimization algorithm when planning tumor-treating fields therapy should maintain or increase the intensity of the electric field applied to the tumor while minimizing the intensity of the electric field applied to organs at risk. This would enhance the effectiveness of tumor-treating fields therapy while reducing dangerous side effects.

• 한국체육학회지인문사회과학편
• /
• 제56권4호
• /
• pp.575-584
• /
• 2017

이 연구에서는 비만중년여성을 대상으로 저강도 저항운동의 속도 차이가 신체조성, 근활성도 및 근력에 미치는 영향을 검토하는데 그 목적이 있다. 연구대상은 비만중년여성 24명을 일반속도의 저항운동집단(normal resistance training speed group; NSG, n=12) 및 느린속도의 저항운동집단(slow speed resistance training group; SSG, n=12)으로 무작위 분류하였다. NSG는 신장성 수축 1초, 등척성 수축 1초 및 단축성 수축 1초의 총 3초간으로 구성하여 35회 3세트를 실시하였으며, SSG는 신장성 수축 3초, 등척성 수축 1초 및 단축성 수축 3초의 총 7초간으로 구성하여 15회 3세트를 실시하였다. 1RM 30%의 저강도 저항운동은 두 집단 모두 동일하게 세트 당 105초, 세트 간 1분 및 운동 간 3분의 휴식시간, 그리고 주 2~3회의 4주간에 걸쳐서 실시하였다. 신체조성, 근활성도 및 근력은 운동전과 운동 4주후에 각각 동일한 방법으로 측정하였다. 신체조성에서 NSG는 WHR에서, SSG는 체지방률에서 운동 전과 비교하여 운동 후에 각각 유의하게 감소하였다(p<.05). 근활성도에서 NSG 및 SSG는 위팔두갈래근, 안쪽넓은근 및 가쪽넓은근에서 운동 전과 비교하여 운동 후에 각각 유의하게 감소하였다(p<.01, p<.05). 근력에서 NSG 및 SSG는 biceps curl 및 leg extension에서 운동 전과 비교하여 운동 후에 각각 유의하게 증가하였다(p<.01). 하지만 신체조성, 근활성도 및 근력은 집단 간의 비교에서 통계학적으로 유의한 차이가 나타나지 않았다. 따라서 이 연구에서 신체조성, 근활성도 및 근력은 저항운동의 속도차이(반복횟수)보다는 저항운동의 수행시간(근수축 발생시간)과 밀접한 관련성이 있을 가능성이 시사되었다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.155-160
• /
• 2002

Metal matrix composites had generated a lot of interest in recent times because of significant in specific properties. It was also highlighted as the materials of frontier industry because strength, heat-resistant, corrosion-resistant, wear-resistant were superiored. In this study the strength properties of $Al_{18}B_4O_{33}/AC4CH$ were represented mixing the binder of $Al_2O_3$ and $TiO_2$. It was also fabricated by squeeze casting. $Al_{18}B_4O_{33}/AC4CH$ was fabricated at the melt temperature of $760^{\circ}C$ the perform temperature of $700^{\circ}C$ and mold temperature of $200^{\circ}C$ under the pressure of 83.4MPa and observed SEM. Fatigue crack growth rate tests on compact tension specimen(half-size) of thickness 12.5mm were conducted by using sinusoidal waveform. Compact tension specimens(half-size) were used and fatigue crack growth rate da/dN and stress intensity factor range ${\Delta}K$ were analyzed concerning to the R value of 0.1 and 0.05. In order to find out the value of ${\Delta}K$, load amplitude constant method was applied by the standard fatigue testing method describes in ASTM E647-95a. As the results of this study, Fatigue crack growth rate increased with in creasing the load ratio, Consequently, At equivalent stress intensity factors, the fatigue crack growth rates in MMC were faster than those of AC4CH alloy. then the fatigue life and the fatigue crack growth rate was investigated using scanning election microscopy(SEM)

• 오토저널
• /
• 제5권1호
• /
• pp.32-44
• /
• 1983

In case of $K_{Imax}$ < $K_{Iscc}$, the corrosion fatigue of high strength steel in 0.1N $H_{2}$S $O_{4}$ solution and 3.5% salt water is as follows. 1. The fatigue life shortens in order of 3.5% salt water and 0.1N $H_{2}$S $o_{4}$ solution. 2. The fatigue crack growth rate in air is obtained as the following equation. (dc/dN)$_{atr}$=7.23*10$^{-6}$ (.DELTA. K)$^{2.23}$ 3. The corrosion fatigue crack growth rate in environment is divided into three regions, that is, First Region, Second Region and Third Region from the small cyclic stress intensity. 4. The formation rate of the active surface on metal is slower than the mechano-chemical reaction rate in First Region. The crack growth rate depends on time and the cyclic stress intensity and is expressed as the following equation. (dc/dN)$_{I}$=C(/DELTA. K)$^{\delta}$ 5. The formation rate of the active surface is faster than the mechano-chemical reaction rate in Second Region and the synergistic effect by stress and corrosion becomes slow. In case the fatigue load is large, we have the critical crack growth rate which is not related to the cyclic stress intensity. 6. The corrosion crack growth rate by the mechano-chemical reaction is the same in $H_{2}$S $O_{4}$ solution and salt water, so Hydrogen accelerates the crack growth. 7. The environment has no effect on the corrosion fatigue crack growth rate in Third Region. 8. In First Region and Second Region, dimple is observed on the fatigue fracture surface in 0.1N $H_{2}$S $O_{4}$ solution. 9. The striation is observed in any environment as in air in Third Region and its interval approximately coincide with the crack growth rate.ate.e.e.

• Geomechanics and Engineering
• /
• 제15권2호
• /
• pp.721-728
• /
• 2018

The surrounding rock mass contains cracks and joints which are distributed randomly around tunnels, and in the process of tunnel blasting excavation, radial cracks could also be induced in the surrounding rock mass. In order to clearly understand the impact of radial cracks on tunnel stability, tunnel model tests and finite element numerical analysis were implemented in this paper. Two kinds of materials: cement mortar and sandstone, were used to make tunnel models, which were loaded vertically and confined horizontally. The tunnel failure pattern was simulated by using RFPA2D code, and the Tresca stresses and the stress intensity factors were calculated by using ABAQUS code, which were applied to the analysis of tunnel model test results. The numerical results generally agree with the model test results, and the mode II stress intensity factors calculated by ABAQUS code can well explain the model test results. It can be seen that for tunnels with a radial crack emanating from three points on tunnel edge, i.e., the middle point between tunnel spandrel and its top with a dip angle $45^{\circ}$, the tunnel foot with a dip angle $127^{\circ}$, and the tunnel spandrel with $135^{\circ}$ with tunnel wall, the tunnel model strength is about a half of the regular tunnel model strength, and the corresponding tunnel stability decreases largely.

• 한국해양공학회지
• /
• 제18권5호
• /
• pp.43-49
• /
• 2004

The lightness of components required in the automobile and machine industry necessitates the use of high strength components. In particular, the fatigue failure phenomena, which occurs when using metal, increases the danger to human life and property. Therefore, antifatigue failure technology is an integral part of current industries. Currently, the shot peening is used for removing the defect from the surface of steel, while improving the fatigue strength on surface. Therefore, in this paper, the effect of compressive residual stress of spring steel(JISG SUP-9) by shot-peening on fatigue crack growth characteristics in a stress ratio(R=0.1, R=0.3, R=0.6) was investigated, giving consideration to fracture mechanics. By using the methods mentioned above, following conclusions are drawn: (1) The fatigue crack growth rate(da/dN) of the shot-peening material was lower than that of the un-peening material and in stage I, ΔKth, the threshold stress intensity factor of the shot-peen processed material is high in critical parts, unlike the un-peening material. Also m, fatigue crack growth exponent and number of cycle of the shot-peening material, was higher than that of the un-peening material, as concluded from effect of da/dN. (2) Fatigue life shows more improvement in the shot-peening material than in the un-peening material, and the compressive residual stress of surface on the shot-peen processed operate resistance of fatigue crack propagation.

• PNF and Movement
• /
• 제19권2호
• /
• pp.195-203
• /
• 2021

Purpose: Neurodynamic tests are used to examine neural tissue in patients with neuro-musculoskeletal disorders, although this has not yet been established in the intensity of nerve tension application. This study aimed to investigate the acute effects of neural stretching intensity on nerve excitability using the latency and amplitude of nerve conduction velocity test (NCV) analysis. Methods: Thirty young, healthy male and female subjects (mean age = 21.30 years) voluntarily participated in this study. Nerve excitability was assessed using the median sensory NCV test. The latency and amplitude of the NCV test were measured under four different conditions: reference phase (supra-maximal stimulus, without neural stretching), baseline phase (2/3 of the supra-maximal stimulus, without neural stretching), weak stretch phase (2/3 of the supra-maximal stimulus, with weak neural stretching), and strong stretch phase (2/3 of the supra-maximal stimulus, with strong neural stretching). Results: The NCV latency was significantly delayed after one minute of neural stretching at the baseline, weak phase, and strong phase in comparison with the reference phase. The NCV latency was significantly delayed by increasing the strength of neural stretching. Furthermore, the NCV amplitude was significantly increased at the weak and strong phases, which were under neural stretching, in comparison with the baseline phase. The NCV amplitude was significantly increased by increasing the strength of the neural stretching. Conclusion: Transient neural stretching as a neurodynamic test can increase the sensitivity of the nerve without negatively affecting the nervous system. However, based on the results of this study, strong neural stretching in the neurodynamic test may delay the transmission of nerve impulses and hypersensitivity.