• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.233-238
• /
• 2002

In this paper, the characteristics of fresh and hardened recycled concrete were experimentally compared to investigate the applicability of the recycled fine aggregates with the substitution ratio. Test results show that the workability of the recycled concrete decreases with the increment of substitution ratio of the recycled fine aggregates except for type-D case which has a lower absorption ratio. Also air content was increased with increasing substitution ratio. It was found that the compressive strength and elastic modulus of recycled concrete were decreased with increasing substitution ratio of the recycled fine aggregates. And, the superplasticizer was more effective on the workability recovery of the recycled concrete.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.60-67
• /
• 1995

The factors affecting on the fatigue strength of spot_welded specimens have been studied. The influence of initial overloads on the fatigue life of spot_welded tensile_shear specimens is investigated by considering fatigue crack initiation and crack propagation. The change of strain range and the influence of initial overload are correlated on the basis ol strain results. The results of this study are as follows. l) The initial absolute strain range decreased with initial overloads increase, and absolute strain range decreased before transformation of waveform of strain, but increased after transformation of waveform of strain. 2) In case of subsequent point of inflection of offset strain, the increment of this strain decreased with initial overload increase. 3) As initial overloads increase, the deformation behavior of spot welded parts is restricted after overloading.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.990-996
• /
• 2010

In this study, a method for estimating the effective stress of clays using in-situ penetration test(PCPT) result is proposed. The proposed method is based on a correlation between the PCPT results and strength increment ratio. According to proposed method, no additional testing procedure for collecting undisturbed soil sample is required, which can reduce overall testing cost. To verify this method, for analysis, various analytical solutions were adopted and used. Measured and predicted effective stress are compared on the test results. The verification sites consist of a variety of soil condition. From comparison, it is seen that predicted value of effective stress using the propose method match well those from measured results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.501-506
• /
• 2002

The unbonded prestressed concrete(PSC) members exhibit very different structural behavior from that of bonded PSC members because of having different tendon stress increment. Recently, AASHTO changed the provision of ultimate tendon stress with unbonded tendons, because some researches tried to improve the provision of ultimate tendon stress with unbonded tendons. The purpose of the present study is to compare various Codes with the ultimate failure stresses of prestressing(PS) steels for the unbonded PSC members. To this end, Some national Codes have been collected and analyzed. A series of major influencing variables have been included in the analysis. It was found that the span-depth ratio, neutral axis depth-effective depth ratio, concrete compressive strength, effective prestress, and prestressing steel ratio have great influence on the ultimate failure stress of PS steel in unbonded PSC members. The Comparison indicates that existing formulas including ACI and domestic Code's equations shows some unwarranties. The present study allows more realistic analysis and design of prestressed concrete structures with internal unbonded tendons.

• Korean Journal of Materials Research
• /
• v.9 no.4
• /
• pp.373-377
• /
• 1999

The cure mechanicsm and cure kinetics of diglycidyl ether of bisphenol A(DGEBA)/4,4'-methylene dianiline(MDA)/nitrile(MN, SN, GN) systems were studied by FT-IR and DSC to develop new applications in the biomedical polymer fields. The network structure of the DGEBA/MDA system was changed to the chain-extended network structure by the addition of nitriles. The reactions contributed to the chain extension were the primary amine-nitrile and hydroxyl-nitrile reactions. The chain-extended network structure could be indirectly proved by the decrement of T\ulcorner and the increment of impact strength with the increasing nitrile content. The cure rate of DGEBA/MDA/nitrile system was lower than that of DGEBA/MDA system due to the disturbance of nitrile group in the reaction of primary amine and epoxide groups.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.215-218
• /
• 2006

A study was made to investigate microstructural evolution and mechanical properties of ultra-fine grained (UFG) pure-Ti produced by equal channel angular (ECA) pressings. The deformed structures were analyzed by finite element method and transmission electron microscopy with the increment of straining. After 4 isothermal ECA pressings, initial coarse grains ($30{\mu}m$) were significantly refined to ${\sim}0.3{\mu}m$ with homogeneous distribution of microstructure which was resulted from $180^{\circ}$ rotation of the sample between pressings. UFG pure-Ti exhibited the considerable improvement in yield strength while losing strain hardening capacity as compared to coarse grained microstructure at ambient temperature, which was mainly attributed to ultra-fine grain microstructure with non-equilibrium grain boundaries.

• Magazine of the Korea Concrete Institute
• /
• v.2 no.1
• /
• pp.109-119
• /
• 1990

This study was accomplished to investigate the characteristics of hardening shrinkage and initial creep of epoxy resin concrete depending on the presence of filler. According to the test results, the hardening shrinkage was increased with increment of sLOrage temperature, and the ef¬feel of tempemture on the hardening shrinkage of epoxy resin concrete with 6% filler was more Significant than that of epoxy resin concrete without filler. Also, the initial creep strain was increased with loading times, stress--strength ratio and elastic strain, and the values for opoxy resin concrete with 6 % filler are higher than that for eposy resin concrete without filler.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.185-188
• /
• 2004

Regarding some of the components of the Korean Tilting Train eXpress(TTX), the lightweight-vehicle development was mainly focused to this study, and so as using the materials, the existing material, steel or aluminum carbody was changed to the composite carbody with both design and manufacturing methods. Therefore the evaluation of the performance of joint strength between composite and metallic boundary area, especially the under frame and the carbody was required, and the compressive and the bending tests were conducted as the sub-scale specimen. In this evaluation, there was involved the sufficient strengths at the joint area between the underframe and the carbody, and is resulted as the increment of the safety factor through the observation of failure conditions.

• Advanced Composite Materials
• /
• v.16 no.4
• /
• pp.259-267
• /
• 2007

Mechanical reinforcement of an all-sustainable composite, composed of papyrus stem-milled particles as reinforcement and poly-L-lactic acid (PLLA) resin as matrix, was investigated. The papyrus particles (average diameter of $70{\mu}m$) could be well dispersed in PLLA resin up to 50 wt% without any surface modification. Young's modulus of the composite was 4.2 GPa at 50 wt% of the papyrus content. This is a two-fold increment in modulus as compared to that of the PLLA matrix. The tensile strength of the composite was almost constant around 48 MPa irrespective of the papyrus content. Temperature dependence of the storage modulus demonstrated that the incorporation of papyrus restricts the large drop in the modulus above the glass transition of PLLA.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.1
• /
• pp.43-48
• /
• 2009

The fatigue crack growth behavior of high strength X80 pipeline steel was investigated with compact tension specimens that crack growth directions were aligned either parallel or normal to the rolling direction of the pipeline. Also, the fatigue crack growth rates for welded joint of X80 pipeline steel were investigated with compact tension specimens that crack growth directions were aligned either parallel or normal to the welding line. The experimental results indicated the fatigue crack growth behavior was markedly different in three zones, weld metal, heat affected zone and base metal of welded joints. There was a trend toward increment in the fatigue life of weld metal and heat affected zone as compared with the X80 pipeline steel.