• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.3 s.36
• /
• pp.197-205
• /
• 2005

Development of the packaging is one of the critical issues for commercialization of the RF-MEMS devices. RF MEMS package should be designed to have small size, hermetic protection, good RF performance and high reliability. In addition, packaging should be conducted at sufficiently low temperature. In this paper, a low temperature hermetic wafer level packaging scheme for the RF-MEMS devices is presented. For hermetic sealing, Au-Sn eutectic bonding technology at the temperature below $300{\times}C$ is used. Au-Sn multilayer metallization with a square loop of $70{\mu}m$ in width is performed. The electrical feed-through is achieved by the vertical through-hole via filled with electroplated Cu. The size of the MEMS Package is $1mm\times1mm\times700{\mu}m$. By applying $O_2$ plasma ashing and fabrication process optimization, we can achieve the void-free structure within the bonding interface as well as via hole. The shear strength and hermeticity of the package satisfy the requirements of MIL-STD-883F. Any organic gases or contamination are not observed inside the package. The total insertion loss for the packaging is 0.075 dB at 2 GHz. Furthermore, the robustness of the package is demonstrated by observing no performance degradation and physical damage of the package after several reliability tests.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.259-266
• /
• 2020

In this study, required drill bits and excavation methods were developed for an uneven drilling method that can solve the problem of performance degradation of rock bolts. The developed drill bit's excavation performance was verified using rock with a strength of 100 MPa or more. In addition, for the relative evaluation of the uneven excavation method, experimental specimens were prepared for models with and without irregularities, and tests were performed. As a result of the experiment, the model with unevenness exhibited an average critical draw resistance of 801.6 kN, which is about 1.7 times the value of 468.7 kN for the model without unevenness, thus confirming the effect sufficiently. Therefore, it is expected that the resistance performance will significantly increase despite an increase in the uneven hole diameter of 20 mm. In the future, the results of this study could be used as basic data when performing other studies using numerical analysis models and performance verification through experiments to obtain an optimized rock forming method.

• Journal of Powder Materials
• /
• v.17 no.4
• /
• pp.312-318
• /
• 2010

High speed steels (HSS) were used as cutting tools and wear parts, because of high strength, wear resistance, and hardness together with an appreciable toughness and fatigue resistance. Conventional manufacturing process for production of components with HSS was used by casting. The powder metallurgy techniques were currently developed due to second phase segregation of conventional process. The powder injection molding method (PIM) was received attention owing to shape without additional processes. The experimental specimens were manufactured with T42 HSS powders (59 vol%) and polymer (41 vol%). The metal powders were prealloyed water-atomised T42 HSS. The green parts were solvent debinded in normal n-Hexane at $60^{\circ}C$ for 24 hours and thermal debinded at $N_2-H_2$ mixed gas atmosphere for 14 hours. Specimens were sintered in $N_2$, $H_2$ gas atmosphere and vacuum condition between 1200 and $1320^{\circ}C$. In result, polymer degradation temperatures about optimum conditions were found at $250^{\circ}C$ and $480^{\circ}C$. After sintering at $N_2$ gas atmosphere, maximum hardness of 310Hv was observed at $1280^{\circ}C$. Fine and well dispersed carbide were observed at this condition. But relative density was under 90%. When sintering at $H_2$ gas atmosphere, relative density was observed to 94.5% at $1200^{\circ}C$. However, the low hardness was obtained due to decarbonization by hydrogen. In case of sintering at the vacuum of $10^{-5}$ torr at temperature of $1240^{\circ}C$, full density and 550Hv hardness were obtained without precipitation of MC and $M_6C$ in grain boundary.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.57 no.2
• /
• pp.99-105
• /
• 2012

The main challenges for the development of agricultural bio-degradable mulching film concern the degradation during the lifetime of cultivated crops. A set of rice by-product (rice-hull and rice-bran) based bio-degradable mulching films was developed and tested, following the measurement of standard bio-degradability rate and adaptability in a large scale field experiment. The standard bio-degradability of bio-film passed the KS (Korea standard) regulation. The result of mechanical analysis of bio-degradable mulching film presented a higher mechanical strength and elongation rate compared with polyethylene film. In addition, bio-film could be degraded into fragments within 4 months under the field condition of several upland crops. Bio-degradable mulching film indicated great potential as a new source of agricultural bio-degradable material.

• Journal of Conservation Science
• /
• v.29 no.1
• /
• pp.47-54
• /
• 2013

The following study tests for the effects of mordants on the production of restoration papers during the conservation process of damaged paper artifacts. For this, four different types of synthetic mordants that are being marketed currently ($K_2CO_3$, $AlK(SO_4)_2{\cdot}12H_2O$, $Cu_2SO_4{\cdot}5H_2O$, $FeSO_4$) were selected to produce samples for measuring variable properties through artificial degradation. The research conducts tests for changes in color, tensile index, and pH level (degree of acidity). The results for changes in color have shown that the value of ${\Delta}E^*ab$ of $K_2CO_3$ mordant sample was the highest, and the tests for tensile index have shown that the strength of dyeing sample was decreased in accordance with the aging time, but Changes according to the mordant was not evident. Finally, the findings for pH level have shown that samples with $Cu_2SO_4{\cdot}5H_2O$ and $FeSO_4$ have pH levels drop below 6. As a result, the research have concluded that mordants used for dyeing restoration paper were identified to have an affect in the dyeing and aging characteristics of the paper.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.1
• /
• pp.49-58
• /
• 2017

The phenomena that we experience in everyday life such as snow, rain, wind, and temperature are referred to as weather, and the average state of atmospheric phenomena that occur over a long period of time in a specific region is referred to as climate. In addition, significant variation of climate compared to the average state is referred to as climate change. Concrete structures can have various problems when exposed to elements. Among the problems, the freeze-thaw problem due to extreme climatic factors such as heavy rain and snowfall has become a particularly significant issue recently. The concrete that has been subjected to repeated freeze-thaw rather than too high or low temperature shows serious degradation of durability, and the performance of structures with degraded performance is difficult to recover. Therefore, in this study, concrete durability performance with respect to freeze-thaw from curing conditions change due to wind speed and sunshine exposure time. Concrete freeze-thaw experiment are performed. using wind speed and sunlight exposure time. Also, performance based evaluation through the satisfaction curve based on the freeze-thaw test results are performed.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.2
• /
• pp.41-54
• /
• 1999

Because of relatively heavy dead weight of concrete itself and unavoidable heat of massive concrete in bridge piers, circular hollow columns are widely used in Korean highway bridges. Since the occurrence of 1995 Kobe earthquake, there have been much concerns about seismic design for various infrastructures, inclusive of bridge structures. It is, however, understood that there are not much research works for nonlinear behavior of circular hollow columns subjected to eqrthquake motions. The objective of this experimental research is to investigate nonlinear behavior of circular hollow reinforced concrete bridge piers under the quasi-static cyclic load, and then to enhance their ductility by strengthening the plastic hinge region with glassfiber sheets. Particularly for this test, constant 10 cyclic loads have been repeatedly actuated to investigate the magnitude of strength degradation for the displacement ductility factor. Important test parameters are seismic design, confinement steel ratio, axial force and load pattern. It is observed from quasi-static tests for 7 bridge piers that the seismically designed columns and the retrofitted columns show better performance than the nonseismically designed colums, i.e. about 20% higher for energy dissipation capacity and about 70% higher for curvatures.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.7-12
• /
• 2011

Poly(lactic-co-glycolic acid) (PLGA) is a biodegradable synthetic polymer with acceptable mechanical strength and well-controlled degradation rate. Also, it can be easily fabricated into many shapes. Silk fibroin contains powerful bioactive molecules. We fabricated natural/synthetic hybrid films using 0, 10, 20, 40 and 80 wt% of silk fibroin. Schwann cells (SCs) were seeded on PLGA/silk fibroin hybrid films and confirmed the effects of adhesion and proliferation on SCs according to the content of silk fibroin. In this study, we confirmed PLGA/silk fibroin hybrid film containing 40% and 80% of silk fibroin interrupted adhesion and proliferation of SCs. Films containing 10% and 20% of silk, however, provided suitable environment for growth and proliferation of SCs. These results suggest that silk fibroin provides suitables surface to neural cells and its proper content provides proper culture conditions to improve cell adhesion and proliferation.

• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.127-134
• /
• 2013

The vascular endothelial cells are the inner layers of blood vessels. It regulates the function of blood vessels and proliferation of vascular smooth muscle cells. Poly(lactide-co-glycolic acid) (PLGA) is a biodegradable synthetic polymer with a well-controlled degradation rate and an acceptable mechanical strength. It can be easily fabricated into many shapes. Silk consists of 18 amino acids. It found important for attaching cells cultured in vitro, and maintaining cell functions. In this study, we fabricated silk/PLGA biomaterial hybrid films of 0, 10, 20, 40 and 80 wt% silk. We performed MTT, SEM, ELISA, and immunocytochemistry analyses. We confirmed the adhesion and the proliferation of HAECs on silk/PLGA according to the content of silk, and 40 wt% silk/PLGA hybrid films have superior adhesion and proliferation properties. These results demonstrate that silk/PLGA hybrid films provide suitable surfaces for HAECs, and there is the effect of silk on cell growth and proliferation.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.24 no.1
• /
• pp.1-11
• /
• 2018

In this study, pro-oxidant($d2w^{(R)}$) and rPP/ZnO nanocomposite flexible films for food packaging were prepared, and their mechanical and antimicrobial properties were investigated. As a result, the carbonyl index and hydroxyl index increased with exposured time to heat and UV rays. Surface analysis showed that the addition of zinc oxide improved the dispersibility and compatibility of the polymer, so that the surface of the composite film was smooth and the zinc oxide particles were smaller than the compared film. And it kept the physical properties by heat and UV ray blocking effect, and it worked to reduce decomposition. In the antimicrobial activity test, the microbial reduction rate was 3 logs or more at the use concentration of zinc oxide. The tensile strength was increased and the elongation was decreased. Oxidative degradability of multi-layered film in UV exposured for 72 hours, the molecular weight of the film decreased by 75.6%, 1,294 g/mol Mn and 5,920 g/mol Mw. In the safety analysis of food packaging materials, we obtained that are in standard of polypropylene, a food contact material of domestic law.