• Membrane Journal
• /
• v.22 no.1
• /
• pp.54-61
• /
• 2012

To separate and recover of VOCs, supporting membranes using PEI were prepared by phase separation method and it was coated with PDMS to prepare PEI-PDMS hollow composite membrane. To investigate characteristic of prepared membrane, pure gas permeability was measured using oxygen and nitrogen, the stage cut and permeance property with feed concentration were evaluated using xylene, ethyl benzene, toluene and cyclohexane. Also, to check solvent resistance on VOCs, stress-strain property of membrane with immersion time in solvent were measured by DMA. The permeance value of $O_2$ and $N_2$ showed 63 GPU and 30 GPU respectively. Permeated VOCs concentration was decreased with increasing stage cut. But, conversely, recovery efficiency that was increased with increasing stage cut. As a result of DMA test, the stress and strain were 11.93 MPa and 13.52%, respectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.88-91
• /
• 2003

The forging of Al 6061 has been studied by using finite element analysis and real forging experiment to find out the effect of strain rate and strain on the final forged product. It seems to be well known that the mechanical properties depend on the microstructures of forged products. The hot deformation of Al alleys including Al 6061 has been researched quite a long period on the various aspects. However, the forging of Al alloys seem to have few information, especially the recrystallization, recovery and grain growth. To elucidate the process variables to control those microstuctual aspects the specially designed model was used for finite element simulation and forging experiments, in which the variation of strain and strain rate could be obtained. The effect of strain md strain rate has been related with the microstructures of forging stocks.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.183-186
• /
• 2000

The high temperature deformation behavior of spray-formed Al-19wt%Si-1.87wt%Mg-0.085wt.%Fe alloy was studied by torsion testing in the strain rate range of 0.001-1 sec-1 and in the temperature range of 300-500 $^{\circ}C$. The relationship between stress temperature and strain rate is expressed using the Power law. the behavior of dynamic recrystallization is showed in 300-35$0^{\circ}C$, 1-0.1sec-1 and the behavior of dynamic recovery is showed in 450-50$0^{\circ}C$, 0.01-0.001sec-1 The size of Si particles is mall when the temperature is low and the strain rate is high. The strain rate sensitivity(m) and the apparent activation energy(Q) indicate the dependence on strain rate and temperature for flow stress respectively. The hot ductility is high when m is high and Q is low. The maps of strain rate sensitivity and apparent activation energy suggest the optimum processing conditions.

• Journal of the Optical Society of Korea
• /
• v.3 no.2
• /
• pp.64-68
• /
• 1999

The performance of a fiber Bragg grating strain sensor constructed with 3$\times$3 coupler is investigated. A 3$\times$3 coupler Mach-Zehnder (M/Z) interferometer is used as wavelength discriminator, interrogating strain-induced Bragg wavelength shifts. Two quadrature-phase-shifted intensities are synthesized from the as-coupled interferometer outputs, and digital arctangent demodulation and phase unwrapping algorithm are applied to extract the phase information proportional to strain. Due to the linear relation between the input strain and the output of quadrature signal processing, signal-fading problems eliminated. In the experiment, a fiber grating that was surface adhered on an aluminum beam was strained in different ways, and the photodetector signals were transferred and processed in a computer-controlled processing unit. A phase recovery fo 7.8$\pi$ pk-pk excursion, which corresponds to ~650$\mu$strain pk-pk of applied strain, was demonstrated. The sensor system was stable over the environmental intensi쇼 perturbations because of the self-referencing effect in the demodulation process.

• Korean Journal of Materials Research
• /
• v.17 no.10
• /
• pp.521-525
• /
• 2007

The microstructure and mechanical properties of an oxygen free copper processed by accumulative roll bonding(ARB) at low strain rate were studied. The copper sheets were highly strained up to an equivalent strain of ${\sim}6.4$ by ARB process at ambient temperature. The strain rate of the copper during the ARB was $2.6sec^{-1}$. The microstructure and mechanical properties of the ARB-processed copper were compared to those of the specimens processed by ARB at relatively high strain rate ($37sec^{-1}$). The microstructure and mechanical properties of the copper with ARB process was very similar to each other despite of some differences in recovery.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.3
• /
• pp.195-200
• /
• 2016

In this study, compression tests for the polyisocyanurate foam which is recognized as the insulation material for the storage tank of the liquefied natural gas (LNG) were carried out for investigation of the material characteristic of mechanical behavior. Deformation recovery ratio according to the various initial deformation levels were estimated and the mechanical behavior of foams that are experienced compressive deformation was also obtained experimentally. The test results were analyzed based on the conditions of initially applied strain level and engineering strain rate.

• Composites Research
• /
• v.28 no.4
• /
• pp.204-211
• /
• 2015

This paper presents a theory related to a two-dimensional linear cross-sectional analysis, recovery relationship and a one-dimensional nonlinear beam analysis for composite wing structure with initial twist. Using VABS including a related theory, the design process of the composite rotor blade has been described. Cross-sectional analysis was performed at cutting point including all the details of geometry and material. Stiffness matrix and mass matrix were linked to each section to make 1D beam model. The 3D strain distributions within the structure were recovered based on the global behavior of the 1D beam analysis and visualize numerical results.

• Transactions of Materials Processing
• /
• v.9 no.2
• /
• pp.193-202
• /
• 2000

The influence of rolling draughts on the formation of through-thickness textures in aluminum 5000X sheet was investigated by X-ray texture measurements and microstructure observations. In order to intensify the deformation inhomogeneities, cold rolling was performed without lubrication. Applying a large draught gave rise to the formation of the shear texture at the surface, whereas a normal plane strain testure formed at the surface after deformation with a small draught. The orientation density along the $\beta$-fiber orientations which developed in the center layer of the rolled specimen was also dependent on the strain gradients in a roll gap. Upon annealing, the deformed substructure of sample surfaces was transformed into a fine grained recrystallized microsturcture through extended recovery reaction. However, coarse grains developed after the discontinuous recrystallization which gave rise to the development of the Cube-texture.

• Advances in aircraft and spacecraft science
• /
• v.1 no.2
• /
• pp.145-175
• /
• 2014

The results of a series of numerical experiments are presented to verify some of the important developments made in the first part of this paper. Firstly, the static solution of an algebraic system obtained through Strong Formulation Finite Element Method (SFEM) is presented. Secondly, the stress and strain recovery procedure is descripted for the present technique. It will be clear that the present approach is suitable for any strong formulation finite element methodology, due to the presented general approach based on the unknown displacements and on the elasticity equations. Thirdly, the numerical solutions for some classical and other numerical results found in literature are exposed. Finally, an arbitrarily shaped composite plate is solved and good agreement is observed for all the presented cases.

• Textile Coloration and Finishing
• /
• v.7 no.4
• /
• pp.25-32
• /
• 1995

This study was carried out to examine the influences of fatigue and perspiration on the deterioration of chrome leather for shoes. The samples were treated with acidic and alkaline artificial perspirations and applied cyclic tensile stress, and the elastic recovery from fatigue strain, tensile strength and elongation, stiffness etc. by regions and directions were determined. The physical properties generally indicate considerable difference by regions and directions due to the thickness, entangling state, and arrangement direction of fiber buldles within the leather. By the treatment of artificial perspirations, the length, weight, strength, elastic recovery from fatigue of the lether are decreased and the thicknes, elongation, and stiffness are increased; and their extents by the alkaline perspiration are higher than those by the acidic one. The elastic recovery from fatigue of samples are decreased with increasing fatigue cylcle; and indicate regressive relations against the logarithm of the elapsed time, and the means of regression coefficients are 2.73 > 2.55 > 2.22 for samples treated by the acidic perspiration, untreated, and treated by the alkaline perspiration, respectively. The tensile strength is decreased and elogation is increased by fatigue, but the changes are diminished likely due to a rearrangment of fiber bundles with increasing fatigue cycle. And the samples become a little flexible immediately after fatigue; but stiffen again with elastic recovery from fatigue strain, consequently for some cases their stiffness after recovery are rather greater than those before fatigre.