• 대한기계학회논문집A
• /
• 제25권6호
• /
• pp.930-937
• /
• 2001

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.29-32
• /
• 2005

This paper presents experimental analysis of a friction-driven wheel that is responsible for wheel squeal. Squeal noise generating mechanism and environment of train u heels has been tried to reproduce under laboratory condition. Scale down size rail and wheel are made and influential parameters to squeal noise are measured, e. g. frictional force, pressure between rail and wheel, creep speed of rail. Negative damping characteristic curve are calculated currently. Necessary relating computational analysis is also carried on.

• 한국철도학회논문집
• /
• 제11권2호
• /
• pp.176-181
• /
• 2008

철도차량의 차륜과 레일 시스템을 모사한 스킬소음 발생장치를 통해 실험을 수행하여 관련 원리를 실험적으로 증명하고 스킬소음 발생 메커니즘에 대한 체계적인 연구를 수행하였다. 이를 위해 스킬소음발생 메커니즘 연구를 소음원-전달계-반응계의 단계별로 진행하였다. 또한 차륜과 레일간의 스틱-슬립 운동에 의한 상대속도 또는 미끄러지는 수준과 마찰결과로서 계산되는 크립곡선과 발생 음압을 시간 및 주파수 영역에서 관찰하여 스킬 소음이 발생하는 조건을 살펴보았다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.442-445
• /
• 2011

Concrete track on the new railway lines of the existing roads are built on high ground, or less than 400m radius of the sharp curve sectors will occur. sharp curve sectors the rail and wheel friction, stick-slip due to the band of 1,000Hz or squeal noise occurs from the increase in civil complaints about noise is a real situation. In this study, discussed in previous studies, noise measurements for each radius of concrete track and frequency analysis, followed by the radius of the curve in order to investigate vibration characteristics of urban railway sector sharp curve radius less than 400m and 400m ~ 1,000 m further to the point selected track components(rails, sleepers, ballast) according to the vibration measurements and analysis of the frequency characteristics and the results were derived.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.331.1-331
• /
• 2002

Four degrees of freedom mathematical model is presented to describe the fundamental mechanisms of the disc brake squeal noise. A contact parameter is introduced to describe the coupling between the in-plane and the out-of-plane motions. The friction coeficient including "relative velocity" and ′normal force" can be generally formulated as the form of multiplication with polynominal parameters(${\beta}$, ${\gamma}$). (omitted)

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.79-84
• /
• 2001

The motivation behind this work is to understand the phenomenon of friction-induced vibration and squeal due to misalignment. In present paper, it is studied on effect of misalignment between friction-induced vibration and squeal by an experiment using a pin-on-disk type experimental apparatus. In order to build an analytical model of the friction-induced vibration system with misalignment, the system is modeled as a single-DOF and 3-DOF system. The results show that the single DOF system can only show stick／slip phenomenon, but the 3-DOF system can show squeal due to misalignment. Consequently, it can be said that the misalignment in a friction-induced vibration system is a source of squeal noise.

• 한국소음진동공학회논문집
• /
• 제15권2호
• /
• pp.206-212
• /
• 2005

In many machines handling lightweight and flexible media, such as magnetic tape drives, xerographic copiers and sewing machines, the media must transit an open space. It is important to predict the static and dynamic behavior of the sheets with a high degree of reliability. The nonlinear theory of the dynamic elastica has often been used to a nonlinear dynamic deflection model. In this paper, the governing equation is derived and simulated by the finite difference method. The parametric cubic curve is applied for defining the guide shape. The dynamic contact conditions suggested by Klarbring is used to predict the direction of the flexible media according to the initial velocity and the friction coefficient. The analysis is also compared to the conventional model, showing that after contacting a $45^{\circ}$ wall, the directions of flexible media of two models are different.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.492-497
• /
• 2013

In this study, a parametric study is performed to investigate the squeal noise of an automobile water pump. The squeal noise studied in this paper is generated by the self-excited torsional resonance of the rotating shaft, and this noise is related to the stick-slip phenomenon of the mechanical seal in the water pump. The mechanical seal friction has the characteristics of the negative velocity-gradient. The equations of motion of multiple-degree-of-freedom torsional vibration model is constructed by the Holzer's method and then the equation is transformed to an equivalent single-degree-of-freedom torsional resonance simulation model. A squeal noise criteria is determined by the simulation model to perform the parametric study. The design parameters(the mass moment of inertia of the pulley, the mass moment of inertia of the impeller, the length of the shafts, the radius of the shafts, spinning speed of the shafts, the position of the mechanical seal, radius of the mechanical seal, and normal load of the mechanical seal) are investigated to confirm the stability for the squeal noise.

• 한국소음진동공학회논문집
• /
• 제23권7호
• /
• pp.624-630
• /
• 2013

In this study, a parametric study is performed to investigate the squeal noise of an automobile water pump. The squeal noise studied in this paper is generated by the self-excited torsional resonance of the rotating shaft, and this noise is related to the stick-slip phenomenon of the mechanical seal in the water pump. The mechanical seal friction has the characteristics of the negative velocity-gradient. The equations of motion of multiple-degree-of-freedom torsional vibration model is constructed by the Holzer's method and then the equation is transformed to an equivalent single-degree-of-freedom torsional resonance simulation model. A squeal noise criteria is determined by the simulation model to perform the parametric study. The design parameters(the mass moment of inertia of the pulley, the mass moment of inertia of the impeller, the length of the shafts, the radius of the shafts, spinning speed of the shafts, the position of the mechanical seal, radius of the mechanical seal, and normal load of the mechanical seal) are investigated to confirm the stability for the squeal noise.

• 한국정밀공학회지
• /
• 제28권5호
• /
• pp.572-577
• /
• 2011

Curve squealing of inter-city railway vehicle is a noise with high acoustic pressure and rather narrow frequency spectra. This noise turns out to be very annoying for the people living in the neighborhood of locations and the passenger in railway vehicle where this phenomenon occurs. Squealing is caused by a self-exited stick-slip oscillation in the wheel-rail contact. Curve squeal noise of railway vehicles that passed by a factor of the speed limit, so to overcome in order to improve running performance is one of the largest technology. In the present paper, characteristic of squeal noise behavior at the Hanvit-200 tilting train test-site. Curve squealing of railway wheels/rail contact occurs in R400~ R800 curves with a frequency range of about 4~11 kHz. If the curve is less than the radius of wheel frail contact due to |left-right| noise level difference (dBA) shows a significant effect of squeal noise were more likely.