• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.162-169
• /
• 2000

This study was carried out to develop a continuously variable-speed transmission(CVT) for agricultural tractor. A full-toroidal CVT mechanism with four discs and six rollers was selected as a device for changing speed ratio continuously. In the step of system layout design, the sizes of roller cylinders and end-load cylinder, which were critical factors for controlling the variator, were designed. Also the control pressure range was designed to limit the contact pressure of variator. In order to make the maximum speed of vehicle as 30km/h, the planetary gear and the six pairs of gears were designed. Also the hydraulic clutch, silent chain, hydraulic manifold and electronic controller were designed. After the design, a prototype with CVT controller was developed and tested. The speed of vehicle was changed continuously to the speed set by driver and the settling time was about 0.52 second at the step-response test (reduction ratio of variator 2.0 to 1.0), which was acceptable as a response time for working with tractor.

• 대한전자공학회논문지
• /
• 제27권6호
• /
• pp.871-878
• /
• 1990

The control method which electrically subdivides 1 step(1.8\ulcornerstep) of a PM step motor into 64 micro-step (0.028\ulcornerstep) is realized using micro-step algorithm on the basis of the look up table method and the position and velocity control using Z-80 microprocessor is also realized. With micro-stepping. The resolution of the system is improved, also by micro-step control of driving-current of the step motro, which is followed by the increase of micro-step subdivision-coefficient, the precise position and velocity control of step-motor can be realized and the stabilization of the system is improved.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권2호
• /
• pp.1135-1138
• /
• 2007

This paper presents motion picture artifacts measured with a high-speed camera. Measurement results of the high-speed camera on moving targets will be evaluated and compared with motion blur data derived from step responses measured on stationary test patterns with a spot-photodetector.

• 한국정밀공학회지
• /
• 제18권6호
• /
• pp.43-49
• /
• 2001

A reduced machining time and increased accuracy for the sculptured surface are very important when producing complicated parts. The step-size and tool-path interval are essential components in high speed and high resolution machining. If they are small, the machining time will increase, whereas if they are large, rough surfaces will be caused. In particular, the machining time, which is key in high speed machining, is affected by the tool-path interval more than the step-size. The conventional method for calculating the tool=path interval is to select a small parametric increment of a small increment based on the curvature of the surface. However, this approach also has limitations. The first is that the tool-path interval can not be calculated precisely. The second is that a separate tool-path interval needs to be calculated in each of the three cases. The third is that the conversion from Cartesian domain to parametric domain or vice versa must be necessary. Accordingly, the current study proposes a new tool-path interval algorithm that do not involve a curvature and that is not necessary for any conversion and a variable step-size algorithm for NURBS.

• 한국전자파학회논문지
• /
• 제14권10호
• /
• pp.1104-1111
• /
• 2003

본 논문에서는 직접 변환 방식의 수신기에서 발생하는 I 채널 및 Q 채널 간의 이득 및 위상 불일치를 보상하는 방법에 대해서 기술한다. 직접 변환 방식의 복조기에서의 이득 및 위상 불일치를 가변 스텝(Variable Step-size) 적응적 루프를 이용하여 블라인드(blind) 등화 방식으로 보상하는 알고리즘을 된 논문에서 제안한다. 이득 및 위상 불일치를 보상하기 위해 일반적인 블라인더 등화 기법을 이용할 경우 루프 이득에 따라 수렴속도와 지터(jitter) 영향이 trade-off 관계에 있다. 본 논문에서는 이들 문제를 극복하기 위하여 적응적 루프의 이득을 오차에 따라 가변 하는 방법을 제시한다. 본 논문에서는 가변 스텝 적응적 루프를 이용하여 빠른 수렴속도와 지터의 영향을 줄이도록 하는 방법을 제시하였고, 모의실험을 통하여 신호 손실 보상과 수렴 속도의 향상을 확인한다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.504-509
• /
• 2003

In this paper, a multi-step optimization using a G.A.(Genetic Algorithm) with variable penalty function is introduced to the structural design optimization of a high speed machining center. The design problem, in this case, is to find out the best cross-section shapes and dimensions of structural members which minimize the static compliance, the dynamic compliance, and the weight of the machine structure simultaneously. The first step is the cross-section shape optimization, in which only the section members are selected to survive whose cross-section area have above a critical value. The second step is a static design optimization, in which the static compliance and the weight of the machine structure are minimized under some dimensional constraints and deflection limits. The third step is a dynamic design optimization, where the dynamic compliance and the structure weight are minimized under the same constraints as those of the second step. The proposed design optimization method was successful applied to the machining center structural design optimization. As a result, static and dynamic compliances were reduced to 16% and 53% respectively from the initial design, while the weight of the structure are also reduced slightly.

• 전자공학회논문지SC
• /
• 제49권4호
• /
• pp.69-77
• /
• 2012

본 논문에서는 스텝모터(step motor)에 대한 PLL(phase locked loop) 타입의 위치제어 방법을 제안한다. 제안된 제어 방법은 기존의 개루프(open loop) 위치제어 방법의 주요 문제점인 급 가, 감속 시의 탈조 현상을 발생시키지 않으며 정지마찰력 때문에 발생되는 정상상태 위치오차를 완전히 없애준다. 또한 고속에서 더 큰 토크를 발생하여 구동 가능한 속도제어 범위가 더 크며 진동과 소음도 줄여준다. 제안된 제어기의 성능을 확인하기 위해 시뮬링크(Simulink)를 이용하여 스텝모터에 대해 시뮬레이션 한 결과를 제시한다.

• Physical Therapy Rehabilitation Science
• /
• 제11권2호
• /
• pp.215-223
• /
• 2022

Objective: This study was to resolve the limitations of the experimental environment and to solve the shortcomings of the method of measuring human gait characteristics using optical measuring instruments. Design: A cross-sectional study. Methods: Fifteen healthy adults without a history of orthopedic surgery on the lower extremities for the past 6 months were participated. They were analyzed gait variables using the smart guide and the 3D image analysis at the same time, and their results were compared. Visual-3D was used to calculate the analysis variables. Results: The reliability and validity of the data according to the two measuring instruments were found to be very high; gait speed(0.85), cycle time(0.99), stride time of both feet(0.98, 0.97) stride legnth of both feet(0.86, 0.88) stride per minute of both feet(0.99, 0.96), foot speed of both feet(0.90, 0.91), step time of both feet(0.77, 0.71), step per minute(0.72, 0.74), stance time of both feet(0.96, 0.97), swing time of both feet(0.93, 0.79), double step time(0.81), initial double step time(0.84) and terminal step time(0.76). Conclusions: In the case of the smart insole, which measures human gait variables using the pressure sensor and inertial sensor inserted in the insole, the reliability and validity of the measured data were found to be very high. It can be used as a device to replace 3D image analysis when measuring pathological gait.

• 대한물리의학회지
• /
• 제12권3호
• /
• pp.99-104
• /
• 2017

PURPOSE: Gait disturbances in patients with hemiplegic stroke involve asymmetry of stance time. Step box training is used to supplement the limitations of stair walking training and increasing the torque value of the paralyzed lower leg's strength. This study aimed to investigate whether step-up training on unstable support could change walking ability in patients with chronic stroke. METHODS: Thirty stroke patients were randomly assigned to the step-up training group (experimental group), that performed training on an unstable surface, and the control group, that performed training on a stable surface. Walking speed, step length, and cadence were measured before and after training. Paired t-tests were used to compare pre- and post-intervention data, while the independent samples t-test was used to determine intergroup differences. Values of p < .05 were considered statistically significant. RESULTS: There was a significant difference in walking ability before versus after the intervention in both groups, although the experimental group showed greater differences than the control group (walking velocity by 8.1%; step length of the non-paralyzed side by 6.9%, respectively; p<.05). CONCLUSION: Step-up training might be more effective on an unstable surface than on a stable surface for increasing walking speed and step length of the non-paralyzed side.

• 대한전기학회논문지:전력기술부문A
• /
• 제55권5호
• /
• pp.179-184
• /
• 2006

In a power system, an out-of-step condition causes a variety of risk such as serious damage to system elements, tripping of loads and generators, mal-operation of relays, etc. Therefore, it is very important to detect the out-of- step condition and take a proper measure. This paper presents a study on implementation of out-of-step detection algorithm using VHDL(Very high speed Hardware Description Language). The structure of out-of-step detection algorithm is analyzed for development of out-of-step detection relay on the FPGA(Field Programmable Gate Array). The out-of-step algorithm is separated to 4 parts: DFT IP, complex power calculation IP, out-of-step detection IP, control unit. Each parts are developed and simulated by using VHDL.