• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.573-578
• /
• 1988

The objectives of this paper are to establish an equivalent magnetic circuit of the hybrid PM step motor and to apply the canonical piecewise linear eqation and the Kazenelson algorithm of solving the nonlinear magnetic circuit, so that the static holding torque and the magnetic properties of the motor are determined. The results of that are applied to the design of the hybrid step motor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.7
• /
• pp.1360-1365
• /
• 2011

Electro-hydraulic servo motor is used to a lot of in the field of industrial equipment which requires one of the control functions among pressure, flow, and power output. In this paper, linear discrete reference model of the electro-hydraulic servo motor system are made for 1-step ahead predictive control. The parameters of electro-hydraulic servo motor system are estimated using the recursive least square method. 1-step ahead predictive model output of electro-hydraulic servo motor system corresponded to reference model output in spite of estimated parameters are not meet real parameters. Control performance affections are studied due to the forgetting factors variation.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.594-596
• /
• 1987

In this study, a method of obtaining reasonably large and constant torque at high speed is given in order to improve the performance of the open loop controlled step motor system using the current source, thus resulting in high performance compared to the conventional current limiting using resistor and chopper.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.5
• /
• pp.223-229
• /
• 2023

This Paper propose the method that measure main system parameters for PI(proportional-integral) current control of a.c. motor adopting the vector control technique. For current control, the PI control input is could be tuning by several selective methods. Among the several methods, the method that using the main system parameters, wire resistance and inductance, are frequently used. In this study, the technique to dissect and measure these two system parameters through the results of simple feedback control. This analytic measurement method is measuring parameters step by step dissecting the results of P control using simple proportional feedback gain about the unit step or multiple step reference command. This strategy is an real time analytic measurement method that calculate current control gains of torque component and flux component both for vector control of A.C. motor without introducing the further measurement circuits and complex measuring algorithms.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.536-539
• /
• 2004

In this paper, a brief discussion on I-PD position controller design for step motor drive is presented. The proposed method mainly focuses on the robustness property of the controller, which is very important for this type of system in which the variation of external load affects plant parameters. It is considered in this paper that two types of controller design methods namely; Coefficient Diagram Method (CDM), and arbitrary Pole Assignment Method (PAM) are treated and compared them. The control plant chosen for our study is a SM inherently is comprised of some non-linear elements. A the scope of the design method is limited to only linear time invariant systems, the SM modeling is approximated to linear system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.6
• /
• pp.389-395
• /
• 2019

This paper presents the sensorless position control of an auxiliary scaffolding step system for vehicles using DC motors. The designed auxiliary scaffolding step has a mechanical protector at the stop position. At this position, the scaffolding is forcibly stopped by the mechanical protector, and the motor current is dramatically increased to the stall current of the DC motor, thereby increasing the electrical damage. In this study, the estimated back EMF- and current model-based observers are proposed to estimate the motor speed and stop position. A simple V/F acceleration voltage pattern is used to operate the auxiliary scaffolding system. The estimated moving position is adopted to determine the stop position of the DC motor with the load current state. The operating current of the DC motor can be reduced by the estimated moving position and V/F acceleration pattern. At the stop position, the proposed sensorless position controller can smoothly stop the DC motor with the estimated moving position and reduced load current without any mechanical and electrical stress from the stall current from the mechanical protector. The proposed control scheme is verified by the comparison of simulations and experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.392-395
• /
• 2003

In the maritime container terminal, LMTT (Linear Motor-based Transfer Technology) is horizontal transfer system for the yard automation, which has been proposed to take the place of AGV (Automated Guided Vehicle). The system is based on PMLSM (Permanent Magnetic Linear Synchronous Motor) that is consists of stator modules on the rail and shuttle car (mover). Because of large variant of mover's weight by loading and unloading containers, the difference of each characteristic of stator modules, and a stator module's trouble etc., LMCPS (Linear Motor Conveyance Positioning System) is considered as that the system is changed its model suddenly and variously. In this paper, we will introduce the soft-computing method of a multi-step prediction control for LMCPS using DR-FNN (Dynamically-constructed Recurrent Fuzzy Neural Network). The proposed control system is used two networks for multi-step prediction. Consequently, the system has an ability to adapt for external disturbance, cogging force, force ripple, and sudden changes of itself.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.530-534
• /
• 1989

In this paper we addressed the basic concept of microstepping, analyzed the combined effect of the motor detent torque and the current profile, and implemented a microstepping drive system using an one-chip microprocessor, power MOSFET's, and a 1.8 degree bifilar-wound hybrid-type step motor excited by a bipolar drive. Experimental results show that microstepping produces greater resolution, eliminates resonant step loss, and reduces motor vibrations.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.406-409
• /
• 1997

An economical 4-axis CNC controller employing step motors is designed and implemented in this paper. By using the inherent ability of holding position of the motor, the CNC controller uses open-loop control for removing trajectory error and for a simple hardware. Each drive of axis has an 8-bit microprocessor 89C52 and a PC controls the axes and pendant by means of RS232C serial communication. Backlash is also compensated at the axis controller. While compensating the backlash, the feed rate becomes zero in order to minimize trajectory error. The trajectories of 16ms interval are computed on PC and are sent to motor drives. In the drives, the trajectories are linearly interpolated for 2ms interval. The developed CNC does not require add-on specific motion card on PC. From the experimental results, the validity of the CNC controller based on step motor is proved.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.318-321
• /
• 1997

This paper is about improving characteristic of plant by using micro-step driver method in 5 phase step motor for satisfying the condition of low oscillation and high accuracy in soldering machine. We choose open loop control method for minimizing hardware system and use one chip microprocessor, power MOSFET nd some device to realize accurate micro-step driver system.