• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1114-1115
• /
• 2007

In this paper, a new speed sensorless control based on a fuzzy compensator are proposed for the interior permanent magnet synchronous motor (IPMSM) drives. The conventional proportional plus integrate(PI) control are very sensitive to step change of the command speed, parameter variations and load disturbance. To cope with these problems of the PI control, the estimated speeds are compensated by using the fuzzy logic controller (FLC). In the FLC used by the speed compensator of the IPMSM, the system control parameters are adjusted by the fuzzy rule based system, which is a logical model of the human behavior for process control. The effectiveness of algorithm is confirmed by the experiments.

• Journal of Convergence for Information Technology
• /
• v.9 no.8
• /
• pp.45-52
• /
• 2019

This paper proposes the design of a closed-loop stepping motor drive for real-time Ethernet (RTE), which can be easily applied to a variety of RTE protocols. The proposed design is divided into a closed-loop step motor drive which can be reused for various types of RTE protocol and RTE module developed for each specific RTE protocol. It is based on a layered architecture so that the motion control algorithm can be easily reused independently of the RTE protocol and motion profile. To verify the proposed design, closed-loop motor drives based on EtherCAT and Mechatrolink III were developed and their performances were evaluated. Cycle time was measured to verify the real-time communication performance of the developed EtherCAT and Mechatrolink III based motor drive. As a result, the EtherCAT was 7.5 times faster than the Mechatrolink III when 32 motor drives were connected.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.100-106
• /
• 2006

This paper proposes a full fuzzy-logic-based vector control for a permanent-magnet synchronous motor (PMSM). The high-performance of the proposed fuzzy logic control (FLC)-based PMSM drive are investigated and compared with the conventional proportional-integral (PI) controller at different conditions, such as step change in command speed and load and etc. In the experimental and simulation the FLC is employed in the speed and current controller. The experimental results show to be a suitable replacement of the conventional PI controller for the high-performance drive system.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.12
• /
• pp.868-873
• /
• 1987

In this pater, we have proposed a synthetic main chopper circuit for the chopper controlled electric automobile. The proposed chopper circuit operates as a step-down chopper in powering mode and as a polarity reversion type chopper in regenerative braking mode. In this study, it was found that powering and regenerative braking operations using the separately excited D.C motor can be controlled continuously only by gate signals of the chopper without changing the connection of the circuit.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.578-581
• /
• 1987

하이브리드 스텝 모터와 같은 소형 정밀 모터에서 이를 설계 제작하는 과정에서 가공기술의 부족과 높은 생산 단가로 인하여 모든 부분의 가공에 높은 정밀도를 유지하기는 어렵다. 그러므로 토오크 특성에 영향을 많이 미치는 부위의 가공 정밀도를 향상시킴으로써 생산 단가를 줄일 수 있다. 하이브리드 스텝, 모터에서 구조상의 오차는 모터의 PERMEANCE를 변화시키고 PERMEANCE의 변화는 이와 직접적인 관련을 갖고 있는 토오크를 변화시켜서 결국에는 스텝 모터의 가장 중용한 요소인 정확한 위치 제어를 할 수 없게 된다. 모터의 구조적 결함에 대하여 알아보고 이 과정을 통하여 구한 HOLDING 토오크 값으로부터 정상인 때와 구조적인 오차가 있는 경우에 대한 토오크의 최대치와 DETENT 위치를 서로 비교함으로써 오차에 대한 토오크의 영향을 해석한다.

• Proceedings of the KIEE Conference
• /
• 1983.07a
• /
• pp.79-82
• /
• 1983

상변환에 의한 농형유도전동기의 1/3, 2/3 속도제어 방법에 대하여 연구하였고, 종래의 국수변환 방법과 비교하였다. 1마력, 36슬롯을 모델로 하여 1800, 1200, 600rpm을 얻어 내었으며, 국수변환 방법에 비하여 고정자의 크기, 슬롯수, 동량을 줄일 수 있는 장점을 가지고 있었다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.1
• /
• pp.101-110
• /
• 2002

A method to control the inverter output voltage lineally in over modulation mode of the third harmonics injected PWM inverter is proposed. The third harmonics injected PWM has a extended linear region compared with the sine PWM. But it still has a maximum voltage about 90% compared with the six step inverter. Therefore, to control the output voltage linearly in over modulation mode, analyzing the relationship between the modulation index and the peak of the fundamental component of the modified reference voltage, we can settle the problem in over modulation mode without iteration. Then we can increase the maximum fundamental component of the third harmonics injected PWM inverter comparative to six-step inverter continuously in over modulation mode. The simulation results of the inverter-induction motor system shows the validity of this method and experimental results prove it.

• Journal of Power Electronics
• /
• v.9 no.3
• /
• pp.491-498
• /
• 2009

The hydraulic-oil pump is widely used for building machinery, brake systems of vehicles and automatic control systems due to its high dynamic force and smooth linear force control performance. This paper presents a novel direct instantaneous pressure control of the hydraulic pump system with SRM drive. The proposed hydraulic pump system embeds the pressure controller and direct instantaneous torque controller. Due to the proportional relationship between pump pressure and torque, pressure can be controlled by the motor torque directly. The proposed direct torque controller can reduce inherent torque ripple of SRM, and develop a smooth torque, which can increase the stability of the hydraulic pump. The proposed hydraulic pump system has also fast step response and load response. The proposed hydraulic pump system is verified by computer simulation and experimental results.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.105-108
• /
• 1988

In this paper, a control system design method is proposed for DC motor drive. A state space model is used to control sysytem and for closed loop system the technique of pole assignment is applied. The control system is designed with state feedback theory and to improve the response further more feedforward theory is applied to control system. The microprocessor as a controller and the interfaces in the system are proposed. Digital simulation results for step changes in reference velocity and load torque are shown.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.919-921
• /
• 1995

In this paper, development of Thermal Printer Head(TPH) controller by using gate array having high reliability and good performance is proposed. Over the 3000 gates are performed to control print image data signals and relative peripheral hardwares. The proposed gate array has TPH control circuit, print control and step motor drive, and print image data control, decoder output control parts. This TPH controller will be a good application to FAX or label printer and barcode printers.