• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.301-306
• /
• 2011

The rear of the vehicle generally overhangs the rear axle. As a result, the rear of a vehicle swings to the outside of the rear axle(rear swing-out). In front steering vehicles, rear swing-out is not important because rear swing-out values measured outside the rear edge are relatively small. However, in the case of the bimodal tram with AWS(all wheel steering), the rear swing-out values increase because of the rear steering at a reverse phase angle. Off-tracking is defined as the radial offset between the path of the centerline of the front axle and the path of the centerline of the following axle. In this paper, in addition to determine the turning performance of bimodal tram with AWS, turning radius, swing-out, off-tracking and swept path width were also investigated.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.1
• /
• pp.121-127
• /
• 2010

We consider the robust trajectory tracking control problem for a skid steering mobile robots. A dynamic model is derived accounting for the effects of wheel skidding. The control design utilizes the dynamic feedback linearization techniques, so as to obtain a predictable behavior for the instantaneous center of rotation thus preventing excessive skidding. The additive controller using the sliding mode type is then robustified against the unmodelled dynamics and parameter uncertainty. Simulation results show the good performances under excessively uncorrected estimations of the longitudinal forces and the lateral resistive forces caused by the skidding of the wheels in tracking trajectories.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.32-38
• /
• 2001

This paper presents an approximate synthesis of 5-SS multi link suspension for 2 D.O.F motions. In the proposed synthesis method, alteration curves of camber, toe, kingpin and caster angles are optimized during the bump rebound and the steering motions. And joint positions can be located within desired boundari es. Especially, steering motions are considered for control of kingpin offset and caster trail. Prescribed motions contain both wheel center positions and imaginary kingpin axes in the multi link type suspension. Constraint equations are formulated with di splacement matrix and velocity matrix using instantaneous screw axis.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.613_614
• /
• 2009

Electric power steering(EPS) has many attentions such as fuel consumption improvement, thus it has been widely adopted for automotive application in recent years. In the EPS system, torque vibrations are directly transferred through the steering wheel to the hands of the driver. Hence, the design of PM motors for the EPS should be performed in order to reduce torque ripples including cogging torque. In this paper, Surface mounted Permanent Magnet Synchronous Motor(SPMSM) is designed to reduce torque ripples and cogging torque at a same time for the EPS propulsion and the design results are verified with the experimental ones.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11b
• /
• pp.785-787
• /
• 2010

It is well known that most power steering systems obtain the power by a hydraulic mechanism. Therefore, it consumes more energy because the oil power should be sustained all the times. Recently, to solve this problem the Electric Power System(EPS) or Motor Driven Power System(MDPS) has widely equipped in passenger vehicles. In this research the concurrent simulation technique for an EPS system with MATLAB/SIMULINK and a full vehicle model has been developed. The dynamic responses of vehicle chassis and steering system are evaluated. Then, a full vehicle model interacted with EPS control is concurrently simulated with an impulsive steering wheel torque input to analyze the stability of 'free control' or hands free motion for SUV. This integrated method allows engineers to reduce the prototype testing cost and to shorten the developing period.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.151-153
• /
• 1993

This paper proposes a novel motor drive system for the electric vehicle. In this paper, four-wheel-direct-drive type electric vehicle system is designed and the theoretical and experimental analysis of the system is investigated. The concept of steering not with steering the wheels but with the difference of the motor torque fives the flexibility of the vehicle design and, allows the omission of the differential gear, transmission gear, and drive axles. Thus the proposed system gives the space between wheels and improves the driver's steering performance.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.2
• /
• pp.79-85
• /
• 2007

The skid-steering method that applied a number of mobile robot currently is very effective in narrow area. But it contains several problems of its natural properties, slip, occurred by different direction between vehicle's driving and wheel's rotary. From this thesis we want to suggest suitable structure of $6{\times}6$ skid steering wheeled vehicle and method of driving by analyzing the behavior of $6{\times}6$ skid-steered wheeled vehicle by engineering analytical method

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.162-167
• /
• 2004

In this research the Co-simulation technique for an electric power steering system with MATLAB/SIMULINK and a full vehicle model with ADAMS has been developed. The dynamic responses of vehicle chassis and steering system are evaluated. Then, a full vehicle model interacted with EPS control is concurrently simulated with an impulsive steering wheel torque input to analyze the stability of 'free control' or hands free motion for Sports Utility Vehicle. This integrated method allows engineers to reduce the prototype testing cost and to shorten the developing period.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.26-31
• /
• 2005

ITR(Inne. Tie Rod) is one of the core parts in an automobile steering system. The front wheels are connected to the steering system, which are controlled by steering wheel through the ITR. Improvement of assembling ITR is needed f3r drivers' satisfaction. Therefore, the parameters influencing the rotational torque were studied and analyzed. The useful results can be obtained, and could be applied to manufacture ITR. Through these manufacturing technologies, high quality ITR have been manufactured with high productivity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.513-514
• /
• 2008