• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.2
• /
• pp.252-258
• /
• 2017

In this paper, the bandwidth and gain enhancement of a double-dipole quasi-Yagi antenna (DDQYA) using a modified balun and two directors is studied. The proposed DDQYA consists of two strip dipoles with different lengths, a ground reflector, which are connected through a coplanar strip line, and two directors. The modified balun is used to increase the bandwidth, whereas two directors are appended to the DDQYA to enhance the gain in the middle and high frequency band. The effects of the length and width of the first director on the antenna performance are analyzed, and final design parameters to obtain a gain over 7 dBi at 1.60-2.90 GHz band are obtained. A prototype of the proposed DDQYA is fabricated on an FR4 substrate, and the experimental results show that the antenna has a frequency band of 1.57-3.00 GHz for a VSWR < 2, and measured gain ranges 7.1-7.8 dBi at 1.60-2.90 GHz band.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.19-25
• /
• 2015

In this paper, a design method for a CPW-fed slot antenna for harmonic suppression is studied. The structure of the proposed slot antenna is a rectangular slot antenna appended with stepped impedance resonators (SIRs) at both ends of the slot symmetrically. Optimal design parameters are obtained by analyzing the effects of the length and width of the SIRs on the input reflection coefficient. The optimized harmonic-suppressed slot antenna operating at 2.45 GHz WLAN band is fabricated on an FR4 substrate with a dimension of 42 mm by 30 mm. The slot length of the proposed harmonic-suppressed slot antenna is reduced to 33.3% compared to that of a conventional rectangular slot antenna owing to the appended SIRs. Experiment results show that the antenna has a desired impedance characteristic with a frequency band of 2.39-2.49 GHz for a VSWR < 2, and a measured gain of 2.5 dBi at 2.45 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.12
• /
• pp.915-923
• /
• 2018

A concrete embedded antenna design is proposed for probing the durability of a building at an industrial scientific medical band of 902~908 MHz. The proposed antenna is designed with a stacked slot patch structure for lower impedance variation to a dielectric constant of concrete, as a dielectric constant difference is derived from the moisture content. The proposed structure has a wider bandwidth when a parasitic patch structure is used, which reduces antenna performance degradation resulting from the moisture content of concrete. The measured voltage standing wave ratio of the proposed structure is less than 2 and the beam width is approximately $80^{\circ}$, whereas the gain is greater than 7 dBi. The proposed antenna is fabricated with a rectangle-type concrete block, which is simulated and measured for return loss and antenna gain.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.11
• /
• pp.1518-1523
• /
• 2018

A method for designing a DDQYA fed by a CPW is proposed in this paper. The proposed CPW-fed DDQYA consists of two series-connected strip dipoles, a ground reflector, and a strip-pair director. Instead of the conventional microstrip feed line in which the signal line is located on the substrate opposite to the antenna, a CPW is used because CPW is located on the same side with the antenna, and so the fabrication is easy. The strip-pair director is composed of two horizontally-separated strips, and it is added above the second dipole to enhance the gain in the high frequency region. A prototype of the proposed CPW-fed DDQYA is fabricated on an FR4 substrate. The fabricated antenna has a frequency band of 1.66-3.38 GHz(68.3%) for a voltage standing wave ratio < 2, and measured gain ranges 5.0-7.3 dBi over a frequency band of 1.60-2.90 GHz.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.61-62
• /
• 2016

In this paper, a design method for a compact stepped open slot antenna for an operation in the UWB band is studied. The proposed antenna is miniaturized by inserting L-shaped slots on the ground plane of the stepped open slot antenna through the creation of a resonance in the low frequency, and a strip director is appended to the antenna in order to increase the gain in the middle and high frequency regions. The effects of varying the length of the L-shaped slots, the distance between the director and the slot antenna, and the director length on input reflection coefficient and realized gain characteristics of the proposed antenna are analyzed. The optimized antenna with the size of $30mm{\times}30mm$ is fabricated on an FR4 substrate, and the experiment results show that the antenna has a frequency band of 3.02-11.04 GHz for a VSWR < 2, which assures the operation in the UWB band.

• Journal of Advanced Navigation Technology
• /
• v.23 no.5
• /
• pp.430-436
• /
• 2019

It is needed to develop an antenna with features of subminiature, light weight and multi-band operation for the variaty services in maritime and industrial fields. The PCB pattern antenna is one of the appropreiate antennas solving these requirements. In this research, the design and fabrication of the PCB pattern antenna operating on the single band of 920 MHz are investigated. The final goal is that the development of the dual band PCB pattern antenna operating on 260 MHz and 920 MHz, which is based on the proposed antenna. It is evident that the performance in the frequencies of 902 MHz, 915 MHz and 928 MHz among of 920 MHz ISM band is better than that in other frequencies. It is also confirmed that the differences of the voltage standing wave ratio, return loss, gain and efficiency between three frequencies are less than 5%. It is expected that the development of communication link of 5-10 km is possible when the induced results are applied into the low power wide area (LPWA) network desinged by the rule of -30 dB sensitivity.

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.257-264
• /
• 2022

As it takes a lot of time and money to develop an aircraft, an environment for renovating and using existing operating aircraft has been created. As a result, many old aircraft were renovated, and due to the aging of the aircraft, more demanding cable requirements were required for renovation projects, and as the number of equipment inside the aircraft gradually increased, the difficulty of system integration increased. In order to solve the difficulties of system integration through systematization of verification procedures, this paper explains VSWR, I-loss, which are the main indicators of antenna cable modification, and explains DTF, one of the problem detection methods. It also explains the elements required for cable design, the environment to be measured, and procedures, and introduces the overall process and effect of antenna cable improvement through demonstration cases.

• Journal of Advanced Navigation Technology
• /
• v.26 no.1
• /
• pp.29-34
• /
• 2022

In this paper, the design of a triple dipole quasi-yagi antenna operating in the 2.45 GHz and 5 GHz wireless LAN frequency bands and the 3.5 GHz WiMAX frequency band was studied. The proposed quasi-Yagi antenna consists of three dipoles connected in series with a V-shaped ground plane. The longest half-bow-tie-shaped dipole resonates in the 2.45 GHz band, whereas the medium-length dipole resonates at 3.5 GHz. The shortest dipole resonates in the 5 GHz band. By adjusting the length and width of the dipoles and the spacings between the dipoles, a triple-band directional antenna operating in the 2.45 GHz, 3.5 GHz, and 5 GHz bands are designed, and fabricated on an FR4 substrate with a size of 45 mm × 55 mm. It was confirmed that the fabricated antenna operates in the designed triple bands of 2.32-2.57 GHz, 3.26-3.69 GHz, and 4.50-6.56 GHz for a voltage standing wave ratio less than 2. Gain is maintained above 3 dBi in the three bands.

• Journal of Aerospace System Engineering
• /
• v.17 no.4
• /
• pp.110-117
• /
• 2023

In this paper, the optimal placement of the rotary wing's communication and navigation antennas was evaluated by measuring their performance through ground simulations and flight tests. To select the mounting position of the communication and navigation antenna on the helicopter, after considering the shape and characteristics of the airframe, the radiation patterns, coupling analysis, equipment operation profiles, and antenna type analysis were performed for the aircraft-mounted antenna. Based on the analysis results, a procedure for sequentially performing voltage standing wave ratio (VSWR) measurement and antenna pattern test was established through ground and flight tests of the antenna. The systematic performance measurement method and procedure proposed in this paper were verified through ground and flight tests of the Light Armed Helicopter (LAH) system.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.523-529
• /
• 2021

This paper shows the design and fabrication of antenna embedded in marine buoy for marine IoT service, especially automatic identification system of fishing gears. Frequency band of proposed antenna has dual band of 433 MHz and 920 MHz considering marine IoT extension. Dual pattern monopole type for 920 MHz and meander type for 433 MHz are adopted in the proposed antenna. Voltage standing wave ratio is obtained 1.548 at 433 MHz and obtained 1.5 of mean value at 920 MHz band by measuring the fabricated antenna. The maximum antenna gain of 3.83 dBi is measured at 902 MHz among 920 MHz band, while antenna gain of 433 MHz is obtained 1.18 dBi. Although antenna gain of 433 MHz is low than 920 MHz band, this gain is larger than desired value of -5 dBi. And, it is confirmed that other measured values meet the performance criteria for archiving communication distance of 10 km between marine buoy and fishing ship in automatic identification system of fishing gears.