• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.169-172
• /
• 2004

The effect of the process parameters on the stable lifetime in rapid thermal firing(RTF) was investigated in order to optimize the process for the Cz-silicon. The process temperature was varied between $700^{\circ}C\;and\;950^{\circ}C$ while the process time was chosen 1 s and 10 s. At below $850^{\circ}C$ the stable lifetime for 10 s is higher than that for 1 s and increases with increasing by the process temperature. However, at over $850^{\circ}C$ the improved stable lifetime is not dependent on the process time and temperature. On the other hand, two high temperature processes in solar cell fabrics are combined with the optimized process and the non-optimized process. The last process determines the stable lifetime. Also, the degraded stable lifetime could be increased by processing in optimized process. The decreased lifetime can increase using the optimized oxidation process, which is a final process in solar cells. Finally, the optimized and non-optimized processes are applied solar cells.

• Journal of information and communication convergence engineering
• /
• v.7 no.2
• /
• pp.215-218
• /
• 2009

In this paper, temperature stable current and voltage references using simple CMOS bias circuit are proposed. To obtain temperature stable characteristics of bias circuit a bandgap reference concept is used in a conventional circuit. The parasitic bipolar transistors or MOS transistors having different threshold voltage are required in a bandgap reference. Thereby the chip area increase or the extra CMOS process is required compared to a standard CMOS process. The proposed reference circuit can be integrated on a single chip by a standard CMOS process without the extra CMOS process. From the simulation results, the reference current variation is less than ${\pm}$0.44% over a temperature range from - $20^{\circ}C$ to $80^{\circ}C$. And the voltage variation is from - 0.02% to 0.1%.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.1
• /
• pp.12-25
• /
• 2007

Numerical simulation of the natural gas steam reforming process for on-site hydrogen production in a $H_2$ fueling station was conducted on the basis of process material and heat balances. The effects of reforming parameters on the process efficiency of hydrogen production were investigated, and set-point values of each of the parameters to minimize the sizes of unit process equipments and to secure a stable operability of the reforming process were suggested. S/C ratio of the reforming reactants was found to be a crucial parameter in the reforming process mostly governing both the hydrogen production efficiency and the stable operability of the process. The operation of the process was regarded to be stable if the feed water(WR) as a reforming reactant could evaporate completely to dry steam through HRSG. The optimum S/C ratio was 3.0 where the process efficiency of hydrogen production was maximized and the stable operability of the process was secured. The optimum feed rates of natural gas(NGR) and WR as reforming reactants and natural gas(NGB) as a burner fuel were also determined for the hydrogen production rate of $27\;Nm^3/h$.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2001.05a
• /
• pp.64-76
• /
• 2001

In this paper, A simple image hologram encryption and decryption technique based on the principle of interference are proposed. The technique using the photorefractive material for getting a stable interference pattern is also proposed. And combine these two techniques, I would like to implement a stable optical information security system. In the encrypting process, I would generate binary phase hologram which can reconstruct original image perfectly, and regard this hologram as original image to be encrypted image. And then the hologram is encrypted as randomly generated binary phase image. Reference image is also generated from the encrypted image by applying interference rule. In the decrypting process, I can get a interference intensity by interfering the reference image and the encrypted image in the interferometer. and transform inferference intensity information into phase information. I recover original image by inverse Fourier transforming the phase information. In this process, the intensity information generated by interference of two images is very sensitive to external vibrations. So, I would like to get a stable interference using the characteristic of SPPCM(self pumped phase conjugate mirror) in photorefractive materials, especially BaTiO₃.

• Communications of the Korean Mathematical Society
• /
• v.15 no.1
• /
• pp.123-131
• /
• 2000

Let {X(t) : t $\geq$B 0} be a Symmetric $\alpha$ Stable and H-Self-similar process with stationary increments. We examine a.s. Holder unboundedness of S$\alpha$S H-sssi Chentsov processes and H-sssi Chentsov fields for order ${\gamma}$>H. Finally, we prove a.s. Holder continuity of S$\alpha$S H-sssi processes with ergodic seating transformations for the case of H>1/$\alpha$.

• Communications of the Korean Mathematical Society
• /
• v.21 no.4
• /
• pp.787-794
• /
• 2006

Two main results are presented in relation to subordination, self-decomposability and semi-stability. One of the result is that strict semi-stability of subordinand process by selfdecomposable subordinator gives semi-selfdecomposability of the subordinated process. The second result is a sufficient condition for any subordinated process arising from a semi-stable subordinand and a semi-stable subordinator to be semi-selfdecomposable.

• Journal of the Korea Convergence Society
• /
• v.5 no.4
• /
• pp.163-169
• /
• 2014

A stable neural network control scheme for unknown non-linear systems is developed in this paper. While the control variable is optimised to minimize the performance index, convergence of the index is guaranteed asymptotically stable by a Lyapnov control law. The optimization is achieved using a gradient descent searching algorithm and is consequently slow. A fast convergence algorithm using an adaptive learning rate is employed to speed up the convergence. Application of the stable control to a single input single output (SISO) non-linear system is simulated. The satisfactory control performance is obtained.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.575-580
• /
• 2020

In this study, we simulated an amine regeneration process with heat-stable salts removal unit. We derived the optimal operating conditions considering the flow rate of waste, the removal rate of heat-stable salts, and the loss rate of MDEA (methyl diethanolamine). In the amine regeneration process that absorbs and removes acid gas, heat-stable salt impairs the absorption efficiency of process equipment and amine solution. An ion exchange resin method is to remove heat-stable salts through neutralization by using a strong base solution such as NaOH. The acid gas removal process was established using the Radfrac model, and the equilibrium constant of the reaction was calculated using Gibbs free energy. The removed amine solution is separated and flows to the heat-stable salts remover which is modeled by using the Rstoic model with neutralization reaction. Actual operation data and simulation results were compared and verified, and also a case study was conducted by adjusting the inflow mass of removal unit followed by suggesting optimal conditions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.303-307
• /
• 2007

This paper investigated the effect of the pad buffing process on the material removal characteristics and pad stabilization during silicon chemical mechanical polishing. The pads surface were controlled by the buffing process using a buffer made by the sandpaper. The buffing process is based on abrasive machining by using a high speed sandpaper. The controlled pad by the buffing process show less deformation deviation and stable material removal rate during the CMP process. In addition, the controlled pad ensure better uniformity of removal rate than comparative pads. As a result of monitoring, the controlled pad by the buffing process demonstrated constant and stable friction force signals from initial polishing stage. Therefore, the tufting process could control the pad surface to be uniform and improve the performance of the polishing pad.

• The Journal of Korean Physical Therapy
• /
• v.23 no.2
• /
• pp.7-15
• /
• 2011

Purpose: We investigated the relationship between the muscle activity and kinematic variables of the upper extremity during a push-up task on stable and unstable surfaces. Methods: We recruited 15 healthy subjects. Subjects completed the push-up task on stable and unstable surfaces. Surface electromyograms were recorded from the serratus anterior, upper trapezius, latissimus dorsi, infraspinatus to monitor changes in muscle activity. Markers for kinematic changes of elbow flexion, shoulder extension, shoulder retraction and scapular adduction were attached at C7, the T7 spinous process, both acromions, the scapula superior and inferior angle, the humerus lateral epicondyle, and the ulnar styloid process. Correlation coefficients between muscle activity and kinematic variables were analyzed by SPSS for Windows, version 15.0. Results: On the unstable surface, elbow flexion and shoulder extension increased with increasing muscle activity of serratus anterior, upper trapezius and infraspinatus. On the stable surface, shoulder retraction decreased with increasing muscle activity of serratus anterior and infraspinatus. Scapular adduction decreased with all types of increasing muscle activity, regardless of the support surface. Conclusion: Correlations between muscle activity and kinematic variables were observed on stable and unstable surfaces during a push-up task, while correlations between right and left variables were not clear. These finding suggest that it may be used to develop a rehabilitation program which could be effective in improving shoulder function in patients with shoulder problems.