• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.991-997
• /
• 2004

In this paper, we propose the architecture of modem receiver to fabricate HomePNA 2.0 chip. HomePNA suffers from inferior channel because of bridge tap, the effect of amateur HAM band and so on. To transfer data over such channel, HomePNA 2.0 uses training sequence to equalize channel and uses FD-QAM optionally as modulation method. So modem receiver demodulate QAM based signal and needs optimum architecture that fully uses these transmission feature. As a result of research, we define 2 mode function of modem receiver depending on TX/RX state. In this paper, particularly, we show the algorithm of equalizer, carrier phase recovery and frame synchromzationblock and propose architecture that improve the performance of channel equalization and is stable in operation. In the end, we estimate the performance of proposed HomePNA2.0 modem receiver over HomePNA TEST LOOP using SPW program.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.8
• /
• pp.801-806
• /
• 2015

Journal bearings support rotors using fluid film between the rotor and the stator. Generally, journal bearings are used in large rotor systems such as turbines in a power plant, because even in high-speed and load conditions, journal bearing systems run in a stable condition. To enhance the reliability of journal-bearing systems, in this paper, we study health-diagnosis algorithms that are based on the supervised learning method. Specifically, this paper focused on defining the unit of features, while other previous papers have focused on defining various features of vibration signals. We evaluate the features of various lengths or units on the separable ability basis. From our results, we find that one cycle datum in the time-domain and 60 cycle datum in the frequency domain are the optimal datum units for real-time journal-bearing diagnosis systems.

• Fibers and Polymers
• /
• v.7 no.2
• /
• pp.129-138
• /
• 2006

Using a strain-controlled rheometer, the steady shear flow properties of aqueous xanthan gum solutions of different concentrations were measured over a wide range of shear rates. In this article, both the shear rate and concentration dependencies of steady shear flow behavior are reported from the experimentally obtained data. The viscous behavior is quantitatively discussed using a well-known power law type flow equation with a special emphasis on its importance in industrial processing and actual usage. In addition, several inelastic-viscoplastic flow models including a yield stress parameter are employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models is also examined in detail. Finally, the elastic nature is explained with a brief comment on its practical significance. Main results obtained from this study can be summarized as follows: (1) Concentrated xanthan gum solutions exhibit a finite magnitude of yield stress. This may come from the fact that a large number of hydrogen bonds in the helix structure result in a stable configuration that can show a resistance to flow. (2) Concentrated xanthan gum solutions show a marked non-Newtonian shear-thinning behavior which is well described by a power law flow equation and may be interpreted in terms of the conformational status of the polymer molecules under the influence of shear flow. This rheological feature enhances sensory qualities in food, pharmaceutical, and cosmetic products and guarantees a high degree of mix ability, pumpability, and pourability during their processing and/or actual use. (3) The Herschel-Bulkley, Mizrahi-Berk, and Heinz-Casson models are all applicable and have equivalent ability to describe the steady shear flow behavior of concentrated xanthan gum solutions, whereas both the Bingham and Casson models do not give a good applicability. (4) Concentrated xanthan gum solutions exhibit a quite important elastic flow behavior which acts as a significant factor for many industrial applications such as food, pharmaceutical, and cosmetic manufacturing processes.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.5
• /
• pp.61-69
• /
• 2008

In general, it has been usually used the method that assess rock slope stability using stereographic projection method, limit equilibrium analysis, numerical analysis and slope stability evaluation table. Several methods for assessing the stability of rock slopes has been proposed on the basis of site investigation data. These method adopted different evaluation items and weighting factors by researchers, organization and nation. But the researches for each evaluation items were insufficient. So the effectiveness of rock slope stability evaluation items for geometrical configuration (slope height, slope direction and angle, dip and dip direction of major discontinuity, absolute value for the direction difference for slope and major discontinuities) and topographical characteristic (possibility of topographical water concentration, upper natural slope angle, slope configuration) using 315 failure and stable highway rock slope analysis data, AV (abnormal value) analysis and NMAV (normalized maximum abnormal value) analysis were evaluated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.8C
• /
• pp.803-810
• /
• 2003

This paper addresses an image processing technique for the human papillomavirus (HPV) DNA chip to discriminate whether the probes are hybridized with the target DNA. HPV DNA chip is designed to determine HPV gene-types by using DNA probes for 22 HPV types. In addition to the probes, the HPV DNA chip has markers that always react with the sample DNA. The positions of probe-dots in the final scanned image are fixed relative to the marker- dot locations with a small variation attributable to the accuracy of the dotter and the scanner. The probes are quadruplicated to enhance diagnostic fidelity. frier knowledge including the marker relative distance and the replication information of probes is integrated into the template matching technique with normalized covariance measure. It was demonstrated that the employment of both of the prior knowledges can be accomplished by simply averaging the template matching measures over the positions of the markers and probes. The resulting proposed scheme yields stable marker locating and probe classification.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.6
• /
• pp.737-745
• /
• 2008

Recent developments of process and measurement technology bring much interest to the online monitoring of process operations such as milling, grinding, broaching, etc. The objective of online monitoring systems is to detect process changes as early as possible. This is helpful in protecting facilities against unexpected failures and then preventing unnecessary loss. This paper investigates, when the process monitoring data are obtained as a profile, the monitoring performances of a statistical $T^2$-statistic and a feedforward neural network by using a wavelet transform. Numerical experiments using cutting force data presented by Axinte show that the proposed wavelet based $T^2$-test has an acceptable power in detecting profile changes. However, its operating characteristic is very sensitive to autocorrelation. On the contrary, compared with $T^2$-test, the neural network has more stable performance in the presence of autocorrelation. This indicates that an adaptive feature to analyze noises should be incorporated into the wavelet based $T^2$-test.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.11
• /
• pp.1951-1957
• /
• 2007

A new synthetic strategy based on the acid-base catalyzed sol-gel method was developed for the preparation of a series of mesoporous TiO2 nanoparticles. A key feature of the method involves a gradual change in pH (0.8- 9) during the sol-gel transition, which guarantees easy introduction of mesoporosity without relying on the well-established sonochemical or template approach. In addition, this method leads to the exclusive formation of the anatase phase stable enough to the calcination temperature up to 600 oC. The physicochemical properties of the particles in the series were characterized by various spectroscopic and analytical techniques such as wide-angle XRD, SAXRD, BET surface area, FE-SEM, TEM, FT-IR, TGA, and XPS. The photocatalytic efficiency of these materials was investigated for the oxidation of toluene under UV-irradiation. All but T-ad in the series exhibited high photocatalytic activity pushing the reaction into completion within 3 h. The reaction followed the first order kinetics, and the rate reaches as high as 3.9 × 10?2/min which exceeds the one with the commercially available Degussa P-25 by a factor of 3.2. When comparison is made among the catalysts, the reactivity increases with increase in the calcination temperature which in turn increases the crystallinity of the anatase phase, thus revealing the following rate orders: T-3 < T-4 < T-5 < T-6.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.262-270
• /
• 2004

Basic experiments were carried out using the THT-IV low-power Hall thruster to examine the influences of magnetic field shape and strength, and acceleration channel length on thruster performance and to establish guidelines for design of high-performance Hall thrusters. Thrusts were measured with varying magnetic field and channel structure. Exhaust plasma diagnostic measurement was also made to evaluate plume divergent angles and voltage utilization efficiencies. Ion current spatial profiles were measured with a Faraday cup, and ion energy distribution functions were estimated from data with a retarding potential analyzer. The thruster was stably operated with a highest performance under an optimum acceleration channel length of 20 mm and an optimum magnetic field with a maximum strength of about 150 Gauss near the channel exit and with some shape considering ion acceleration directions. Accordingly, an optimum magnetic field and channel structure is considered to exist under an operational condition, related to inner physical phenomena of plasma production, ion acceleration and exhaust plasma feature. A new Hall thruster was designed with basic research data of the THT-IV thruster. With the thruster with many considerations, long stable operations were achieved. In all experiments at 200-400 V with 1.5-3 mg/s, the thrust and the specific impulse ranged from 15 to 70 mN and from 1100 to 2300 see, respectively, in a low electric power range of 300~1300 W. The thrust efficiency reached 55 %. Hence, a large map of the thruster performance was successfully made. The thermal characteristics were also examined with data of both measured and calculated temperatures in the thruster body. Thermally safe conditions were achieved with all input powers.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11A
• /
• pp.1872-1879
• /
• 2001

As multiview video applications become more popular, correspondence problem for stereo image matching plays an important role in expanding view points. Thus, we propose an efficient dense disparity estimation algorithm considering features of each image pair of multiview image sets. Main concepts of the proposed algorithm are based on the region-dividing-bidirectional-pixel-matching method. This algorithm makes matching process efficient and keeps the reliability of the estimated disparities. Other improvement have obtained by proposed cost function, matching window expanding technique, disparity regularization, and disparity assignment in ambiguous region. These techniques make disparities more stable by removing false disparities and ambiguous regions. The estimated disparities are used to synthesize intermediate views of multiview images. Computer simulation demonstrates the excellence of the proposed algorithm in both subjective and objective evaluations. In addition, processing time is reduced as well.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.3
• /
• pp.575-585
• /
• 2015

The traffic classification is a preliminary and essential step for stable network service provision and efficient network resource management. However, the payload signature-based method has significant drawbacks in high-speed network environment that the processing speed is much slower than other methods such as header-based and statistical methods. In addition, as signature numbers are increasing, traffic analysis speed also declines because of signature matching method that does not consider analytic efficiency of each signature and traffic occurrence feature. In this paper, we propose a signature list reordering method in order by analytic value of each signature. When we reordered the signature list by the proposed method, we achieved about 30% improvement in speed of the traffic analysis compared with random signature list.