• Korean Journal of Materials Research
• /
• v.28 no.3
• /
• pp.159-165
• /
• 2018

In order to increase the efficiency of the sputtering method widely used in thin film fabrication, a dc sputtering apparatus which supplies both high frequency and magnetic field from the outside was fabricated, and cobalt thin film was fabricated using this apparatus. The apparatus can independently control the applied voltage, the target-substrate distance, and the target current, which are important parameters in the sputtering method, so that a stable glow discharge is obtained even at a low gas pressure of $10^{-3}$ Torr. The fabrication conditions using the sputtering method were mainly performed in $Ar+O_2$ mixed gas containing about 0.6 % oxygen gas under various Ar gas pressures of 1 to 30 mTorr. The microstructure of Co thin films deposited using this apparatus was examined by electron diffraction pattern and X-ray techniques. The magnetic properties were investigated by measuring the magnetization curves. The microstructure and magnetic properties of Co thin films depend on the discharge gas pressure. The thin film fabricated at high gas pressure showed a columnar structure containing a large amount of the third phase in the boundary region and the thin film formed at low gas pressure showed little or no columnar structure. The coercivity in the plane was slightly larger than that in the latter case.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.419-421
• /
• 2008

Sputter deposition on a Pt counter electrode was studied using RF plasma as the improvement of conversion efficiency for dye-sensitized solar cells (DSC). The effects of the sputtering thickness and incident angle on a Pt counter electrode for DSC was scrutinized. We conducted the experiment to get the optimal sputtering time for the performance of the DSC. Under the sputtering time condition of 120 seconds, we varied the incident angles of substrate from $0^{\circ}$ to $60^{\circ}$. Under standard test condition (AM 1.5, 100mW/$cm^2$), we obtained the maximum efficiency of 4.61% at the incident angle of $40^{\circ}$ with an active cell area of $1cm^2$.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.3
• /
• pp.588-593
• /
• 2010

Sputter deposition on a Pt counter electrode was studied using radio frequency (RF) plasma as the improvement of incident photon to current conversion efficiency (IPCE) for dye-sensitized solar cells (DSCs). Effects of the sputtering thickness and the incident angle on a Pt counter electrode for DSCs were investigated. Experiments to get the optimal sputtering time for the performance of the DSCs were carried out. And it is found that the optimized sputtering time was 120 seconds, in addition, the incident angles of the substrate was adjusted from $0^{\circ}$ to $60^{\circ}$. The maximum efficiency of 5.37% was obtained at the incident angle of $40^{\circ}$ with an active cell area of $1cm^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.77-78
• /
• 2006

In order to increase the efficiency of LED, transparent electrodes should be also developed. also suitable anti-reflection coating (ARC) is necessary for practical device applications. In our paper, Al-doped ZnO (AZO) films were fabricated by sputtering on GaP substrate(wavelength:620nm). Choosing optimum substrate temperature and sputtering rate, high quality AZO films were formed. We confirmed that the surface and electrical properties, which implemented using the methods of AFM, Hall measurement. The properties of AZO thin films especially depended on the thickness. We presumed that the change of the increase the external quantum efficiency of LED according to the AZO thin film of thickness.

• Current Photovoltaic Research
• /
• v.9 no.1
• /
• pp.1-5
• /
• 2021

The properties of the electron transport layer (ETL) have a great effect on perovskite solar cell performance. Depositing conformal SnO2 ETL on bottom textured silicon cells is essential to increase current density in terms of the silicon-perovskite tandem solar cells. In the recent study, the SnO2 electron transport layer deposited by the sputtering method showed an efficiency of 19.8%. Also, an electron transport layer with a sputtered TiO2 electron transport layer in a 4-terminal tandem solar cell has been reported. In this study, we synthesized SnOx ETL with a various sputtering power range of 30-60W by Radio-frequency (RF)-magnetron sputtering. The properties of SnOx thin film were characterized using ellipsometer, UV-vis spectrometer, and IV measurement. With a sputtering power of 50W, the solar cell showed the highest efficiency of 13.3%, because of the highest fill factor by the conductivity of SnOx film.

• Journal of Surface Science and Engineering
• /
• v.46 no.2
• /
• pp.61-67
• /
• 2013

Thin film solar cells have attracted much attention due to their high cell efficiency, comparatively low process cost, and applicability to flexible substrates. In particular, CIGS solar cells have been widely studied and produced because they demonstrated the highest cell efficiency. However, the deposition process of CIGS films generally includes the selenization process conducted at elevated temperature using toxic $H_2Se$ gas. To avoid this selenization process, CIGS thin films were, in this study, deposited by RF sputtering using single composite CIGS target. In addition, the effects of sputtering bias voltage and heat treatment on the microstructural and morphological changes in deposited CIGS films were investigated and discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.365-366
• /
• 2007

High quality cathode with high deposition rate of thin films and long target life time is required for manufacturing TFT-LCD and semiconductor. We developed WV(wide view) sputtering cathode with wide erosion area and high deposition rate. Ti thin film thickness variation in WV cathode is below 5% for 380 kWh target life time. Al thin film thickness using normal cathode is decreased about 20%. By using WV cathode, target using efficiency was improved 40%. in comparison with normal cathode.

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.930-937
• /
• 1997

Polycrystalline CdTe thin films have been studied for photovoltaic application because of their high absorption coefficient and optimal band energy(1.45 eV) for solar energy conversion. In this study CdTe thin films were deposited on CdS(chemical bath deposition)/ITO(indium tin oxide) substrate by rf-magnetron sputtering under various conditions. Structural optical and electrical properties are investigated with XRD UV-Visible spectrophotometer SEM and solar simulator respectively. The fabricated CdTe/CdS solar cell exhibited open circuit voltage( $V_{oc}$ ) of 610 mV short circuit current density( $J_{sc}$ ) of 17.2 mA/c $m^2$and conversion efficiency of about 5% at optimal sputtering conditions.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.1
• /
• pp.29-34
• /
• 2008

In this paper, the DE(double erosion) cathode for the reactive magnetron sputtering system is developed for high deposition rate and high target utilization efficiency. The utilization efficiency of the developed DE cathode is 22% higher than that of normal SE(single erosion) cathode. Sputtering process for the nickel oxide thin films with the DE cathode is performed under the following conditions; power with $1kW{\sim}3kW$, pressure with 4mtorr and 8mtorr, oxygen flow ratio with $0%{\sim}80%$. As a result, the hysteresis phenomenon of discharge voltage in 4mtorr is lower than that in 8mtorr and the hysteresis phenomenon of discharge voltage is getting lower as the applied power is getting higher. The structure of cross section and surface roughness of the thin films are observed by FE-SEM and AFM. The structure of cross section of the thin films is columnar and the average surface roughness under oxygen flow ratio of 0%, 52.5% and 65.0% are $2.08{\AA}$, $2.20{\AA}$ and $0.854{\AA}$, respectively.

• New & Renewable Energy
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2021

Transparent conducting oxide (TCO) films have been widely used in optoelectronic devices, such as OLEDs, TFTs, and solar cells. However, thin films of indium tin oxide (ITO) have few disadvantages pertaining to process parameters such as substrate temperature and sputtering power. In this study, we investigated the requirements for using TCO films in silicon-based solar cells and the best alternative TCO materials to improve their efficiency. Moreover, we discussed the current status of high-efficiency solar cells using low-temperature TCO films such as indium zinc oxide and Zr-doped indium oxide.