• Journal of Surface Science and Engineering
• /
• v.52 no.6
• /
• pp.283-288
• /
• 2019

MCrAlY overaly coatings are used as oxidation barrier coatings to prevent degradation of the underlying substrate in high temperature and oxidizing environment of the hot section of gas turbines. Therefore, oxidation resistance in high temperature is important property of MCrAlY coatings. Also, coefficients of thermal expansion (CTE) of MCrAlY have middle value of that of Ni-based superalloys and oxides, which have the effect of preventing the delamination of the surface oxides. Cyclic oxidation test is one of the most useful methods for evaluating the high temperature durability of coatings used in gas turbines. In this study, NiCoCrAlY overlay coatings were formed on Inconel 792(IN 792) substrates by vacuum plasma spraying process. Vacuum plasma sprayed NiCoCrAlY coatings and IN 792 susbstrates were exposed to 1000℃ one-hour cyclic oxidation environment. NiCoCrAlY coatings showed lower weight gain in short-term oxidation. In long-term oxidation, IN 792 substrates showed higher weight loss due to delamination of surface oxide but NiCoCrAlY coatings showed lower weight loss. X-ray diffraction (XRD) analysis showed α-Al2O3 and NiCr₂O₄ was formed during the cyclic oxidation test. Through cross-section observation using scanning electron microscopy (SEM) and electron back scatter diffraction (EBSD) analysis, thermally grown oxide (TGO) layer composed of α-Al₂O₃ and NiCr₂O₄ was formed and the thickness of TGO increased during 1000℃ cyclic oxidation test. β phase in upper side of NiCoCrAlY coating was depleted due to oxidation of Al and outer beta depletion zone thickness also increased as the cyclic oxidation time increased.

• FLOWER RESEARCH JOURNAL
• /
• v.17 no.2
• /
• pp.121-127
• /
• 2009

This study was conducted to improve commercial quality of a cut spray chrysanthemum 'Gama' bred in Korea by foliar application of daminozide (DMZ), suppressing excessive elongation of peduncle caused by high temperature in summer season production. Applications were made at three floral bud developmental stages (I, II, and III), and concentrations used were 0, 500, 1000, and $2000mg{\cdot}L^{-1}$. Both cut flower length and peduncle length showed the greatest suppression of elongation by DMZ treatments at stage II. DMZ also gradually reduced values of those in a concentration-dependant manner. Stem thickness and flower diameter reduced compared to control as DMZ was sprayed at later stage and those two characteristics decreased in a concentration-dependant manner. The number of paralleled flowers neighboring apical part of whole plant showed the best results at stage I and II. As for DMZ concentration, those increased effectively at $500-1,000mg{\cdot}L^{-1}$. Among all combinations, $1,000mg{\cdot}L^{-1}$ DMZ at stage II recorded the most paralleled flowers and showed 24.2% increment as compared to control. The number of fully expanded flowers and total floral buds also showed the highest values using $1,000mg{\cdot}L^{-1}$ DMZ at stage II than the other treatments. In cut spray chrysanthemum cultivar 'Gama' bred in Korea, foliar-spraying with $1,000mg{\cdot}L^{-1}$ DMZ at stage II most effectively suppressed excessive peduncle elongation, parallelled flower cluster arrangement, and increased the number of flowers in summer. However, this combination affected negatively the other commercial qualities, reducing cut flower length, stem thickness, and flower diameter. Therefore, we recommended that foliar-spraying stage and DMZ concentration was stage I and $1,000mg{\cdot}L^{-1}$, respectively, in a practical culture for 'Gama'.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.19 no.2
• /
• pp.121-135
• /
• 2016

The present study is an analysis of the monitoring results of the four areas that underwent the experimental construction of Straw-net+seedspray, Vegetation media spray method(t=2cm), and Vegetation media spray method(t=3cm), with the purpose of selecting the adequate revegetation of cutting slopes in weathered granite soil. Cutting slopes are mostly designed in the Straw-net+seedspray method, but since weathered granite soil slopes tend to have an infertile soil quality that runs down, it is difficult for seed germination and growth. It is difficult to apply Straw-net+seedspray to weathered granite soil slopes considering the germination rate and coverage rate of the Straw-net+seedspray method, which accompanies erosion and scouring. The final conclusions are summarized as follows. First, Straw-net+seedspray has difficulty recruiting plants to infertile weathered granite soil, which results in a lower coverage rate and fewer species, so it is not adequate construction method. Second, Vegetation spraying methods with wet media are more advantageous in early revegetation. The wet construction methods are faster than the dry construction methods in terms of early germination and its early growth are more excellent. Third, when constructing Vegetation spray methods with dry media, it were more advantageous if the thickness was thicker. When the soil-media is thicker, the soil is resilient to droughts, so the thickness must be flexibly applied according to the soil quality and slant of the weathered granite soil slope. The present study is a monitoring result for some areas of Gangwon-do, so its results may differ from other areas.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.2
• /
• pp.80-84
• /
• 2018

Mg alloys AZ31 and AZ91 were Plasma-Electrolytic-Oxidized in Na-P and Na-Si system electrolyte at various concentration, applied voltage and time. Thickness and surface roughness of PEO coating were examined. Salt spraying test were carried out to compare their corrosion resistances. Generally, corrosion resistances rate were increased as thickness and crystallinity increasing. Size of pore being larger, long term corrosion resistance decreased. It is turned out that $Mg_2SiO_4$ and other crystalline phase rather than MgO might be increase corrosion resistance dramatically.

• Journal of Surface Science and Engineering
• /
• v.32 no.2
• /
• pp.144-156
• /
• 1999

Thermal Barrier Coating with Functional Gradient Materials (FGM-TBC) can play an important role to protect the parts from harmful environments in high temperatures such as oxidation, corrosion, and wear and to improve the efficiency of aircraft engine by lowering the surface temperature on turbine blade. FGM-TBC can increase the life spans of product and improve the operating properties. Therfore, in this study the evaluations of mechanical and thermal properties of FGM-TBC such as fatigue, oxidation and wear-resistance at high temperatures have been conducted. The samples of both the TBC with 2, 3, 5 layers (YSZ/NiCrAlY) to be produced by Air Plasma Spray method (APS) and the bulk TBC with 6 layers to be produced by Plasma Assisted Sintering method (PAS) were used. Furthermore, residual stress, bond strength, and thermal conductivity were evaluated. The average thickness of the APS was 500$\mu\textrm{m}$ to 600$\mu\textrm{m}$ and the average thickness of the PAS was 3mm. The hardness number of the top layer of APS was 750 Hv to 810Hv and that of PAS was 950 Hv to 1440Hv. The $ZrO_2$ coating layer of APS was composed of tetragonal structure after spraying as the result of XRD analysis. As shown in the results of the high temperature wear test, the 3 layer coating of APS had the best wear resistance at $800^{\circ}C$ and the 5 layer coating of APS had the best wear resistance at $600^{\circ}C$. But, these coatings had the tendency of the low-temperature softening at $300^{\circ}C$. The main mechanism of wear was the adhesive wear and the friction coefficient of coatings was increased as increasing the test temperatures. A s results of thermal conductivity test, the ${\Delta}T$ of the APS coating was increased as number of layer and the range of thermal conductivity of the PAS was $800^{\circ}C$ to $1000^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.4
• /
• pp.444-455
• /
• 2017

This study was conducted to evaluate the effect of panel density and resin content on properties of medium density fiberboard (MDF) to obtain some insights on MDF properties as a function of panel density and resin content. MDF panels with different panel densities such as 650, 700, 750 and $800kg/m^3$ were manufactured by adjusting the amount of wood fibers in the mat forming. MDF panels were also fabricated by spraying 8, 10, 12, and 14% of urea-formaldehyde (UF) resins onto wood fibers in a drum-type mechanical blender to fabricate MDF panels with a target density of $650kg/m^3$. As the panel density and resin content increased, the internal bonding (IB) strength of MDF panel consistently increased. Modulus of rupture (MOR), modulus of elasticity (MOE) and screw withdrawal resistance (SWR) had a similar trend to the IB strength. In physical properties, thickness swelling (TS) and water absorption (WA) decreased with an increase in both panel density and resin content. In addition, the formaldehyde emission (FE) which increased as the panel density and resin content became greater. In overall, the panel density of MDF had more significant effect than the resin content in all properties of MDF panels, indicating that it was better to adjust the panel density rather than the resin content for MDF manufacture.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.3
• /
• pp.311-319
• /
• 1999

The thermal conductivity ${\lambda}_b$, thermal diffusivity ${\alpha}_b$ of the thin black paint layer sprayed on solid surface and absorptivity a for laser beam are measured by applying a non-contact measurement method of the thermophysical properties of solids. The values of a=0.67, ${\lambda}_b=1.45W/mK$ and ${\alpha}_b=1.24{\times}10^{-6}m^2/s$ are obtained for the sprayed lay~ thickness $z_b{\fallingdotseq}40\;{\mu}m$. Furthermore, for the $z_b{\fallingdotseq}24\;{\mu}m$ thick layers which arc formed by rubbing with a glass rod after spraying, the values of a=0.73, ${\lambda}_b=1.85W/mK$. and ${\alpha}_b=1.09{\times}10^{-6}m^2/s$ are obtained. It is also shown that the present thermal diffusivity ${\alpha}_b$ for $z_b{\fallingdotseq}40\;{\mu}m$ Is about 30~80% larger than those obtained by Araki et al. for the thicker layer $z_b{\fallingdotseq}150{\sim}248\;{\mu}m$. This method could be applied to the measurement of thermophysical properties of thin layer on solids.

• The Plant Pathology Journal
• /
• v.34 no.2
• /
• pp.113-120
• /
• 2018

Chlorella, one single-cell green algae organism that lives autotrophically by photosynthesis, can directly suppress some plant diseases. The objective of this study was to determine whether pre-spraying with Chlorella fusca suspension could induce systemic acquired resistance (SAR) in cucumber plants against anthracnose caused by Colletotrichum orbiculare. In order to illustrate SAR induced by algae, infection structures in host cells were observed under a transmission electron microscope (TEM). Cytological changes as defense responses of host mesophyll cells such as accumulation of vesicles, formation of sheath around penetration hyphae, and thickness of cell wells adjoining with intracellular hyphae were demonstrated in cucumber leaves. Similar defense responses were also found in the plant pre-treated with DL-3-aminobutyric acid, another SAR priming agent. Images showed that defense response of host cells was scarcely observed in untreated leaf tissues. These cytological observations suggest that C. fusca could induce SAR against anthracnose in cucumber plants by activating defense responses of host cells.

• Corrosion Science and Technology
• /
• v.19 no.2
• /
• pp.51-56
• /
• 2020

The objective of this study was to improve properties of plasma sprayed HAp layer to titanium substrate by introducing an intermediate layer with two different methods. Before applying Zn doped HAp coating on titanium substrate, an intermediate layer was introduced by titanium plasma spray or titanium anodization. Heat treatments were conducted for some samples after titanium intermediate layer was formed. Zn doped HAp top layer was applied by plasma spraying. Three-point bending test and pull-off adhesion test were performed to determine the adhesion of Zn doped HAp coatings to substrates. Long-term credibility of Zn doped HAp plasma sprayed coatings on titanium was assessed by electrochemical impedance measurements in Hanks' solution. It was found that both titanium plasma sprayed and titanium anodized intermediate layer had excellent credibility. Strong adhesion to the titanium substrate was confirmed after 12 weeks of immersion for coating samples with titanium plasma sprayed intermediate layer. Samples with titanium anodized intermediate layer showed good bending strength. However, they showed relatively poor resistance against pulling off. The thickness of titanium anodized intermediate layer can be controlled much more precisely than that of plasma sprayed one, which is important for practical application.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.141-144
• /
• 2006

The main purpose of this study is to develop a Sprayed FRP repair and strengthening method, which is a new technique for strengthening the existing concrete structures by mixing carbon or glass shot fibers and the epoxy or vinyl ester resins with high-speed compressed air in open air and randomly spraying the mixture onto the concrete surface. At present, the Sprayed FRP repair and strengthening method using the epoxy resin has not been fully discussed. In order to investigate the material property of Sprayed FRP, this study carried out tensile tests of the material specimens which are changed with the combinations of various variables such as the length of shot fiber and mixture ratio of shot fiber and resin. These variables are set to have the material strength equal to one layer of the FRP sheet. As a result, the optimal length of glass and carbon shot fibers were derived into 3.8cm, and the optimal mixture ratio was also deriver into 1:2 from each variable. And also, the thickness of Sprayed FRP to have the strength equal to one layer of FRP sheet was finally calculated.