• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.687-690
• /
• 2004

Fabrication and characterization of dye-sensitized TiO2 solar cells(DSSC) consisting of spray-coated TiO2 electrode, an electrolyte containing I-/I3- redox couple, and a Pt-coated counter electrode carried out, using mainly FE-SEM and solar simulator. Also, effect of rapid thermal annealing(RTA) temperatue on I-V curves of DSSCS consisting of approximately 10m thickness and $5{\times}5mm2$ active area. No significant difference in the apparent size of TiO2 clusters was observed with increasing RTA temperature. Also, an open circuit voltage(Voc) of approximately 0.70V and a short-circuit photocurrent(Jsc) of 8 to 12mA/cm2 were observed in the TiO2 solar cell. With increasing RTA temperature upto 550oC, photocurrent density of dye-sensitized solar cells was enhanced, leading to enhancing the efficiency of dye-sensitized solar cells having Pt-electroplated counter electrode.

• Composites Research
• /
• v.25 no.5
• /
• pp.159-163
• /
• 2012

The coating of metal surface with carbon nanotubes(CNTs) has been studied for the heat transfer enhancement of the boiling and condensation of refrigerant. The multiwalled carbon nanotube/copper oxide(CuO) composite powder, which has been surface modified by dispersant and polyvinyl alcohol solution, was ultrasonically sprayed and sintered on a copper wafer. In this paper, experiments were performed to assess the characterization and comparison of the carbon nanotube before and after sinterning and the morphology changes of the CNT/CuO-coated surface by using different dispersants. The dispersants used are THF (Tetrahydrofuran), SDBS(Dodecylbenzenesulfonic acid sodium salt), SDS(Sodium dodecy sulfate). The samples were examined by scanning electron microscopy(SEM), thermogravimetric analysis(TGA), differential scanning calorimeter(DSC) and Raman spectroscopy.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.188-193
• /
• 2000

A more accurate life prediction for gas turbine blade takes into account the material behavior under the complex thermo-mechanical fatigue(TMF) cycles normally encountered in turbine operation. An experimental program has been carried out to address the thermo-mechanical fatigue life of the IN738LC nickel-base superalloy. In the first phase of the study, out-of-phase and in-phase TMF experiments have been performed on uncoated and coated materials. In the temperature range investigated. the deposition of NiCrAlY air plasma sprayed coating did not affect the fatigue resistance. In the second phase of the study, a physically-base life prediction model that takes into account of the contribution of different damage mechanisms has been applied. This model was able to reflect the temperature and strain rate dependences of isothermal cycling fatigue lives, and the strain-temperature history effect on the thermo-mechanical fatigue lives.

• Journal of Korea Foundry Society
• /
• v.18 no.4
• /
• pp.389-397
• /
• 1998

회주철 모재의 표면에 감압 플라즈마 용사법으로 실리콘 분말을 피복시킨 후 $CO_2$ 레이저를 이용하는 표면 합금화로 고온 내스케일성이 향상된 표면 개질층을 제조하였다. 실리콘의 표면 합금층에는 응집상의 흑연(chunky graphite)이 $Fe_5Si_3$로 구성된 망상의 화합물 기지속에 정출하는 조직특성을 보였다. 대기 분위기에서 18.0ks동안 열중량측정(TG)한 결과 실리콘 표면 합금층의 무게 증가율은 회주철 모재에 비하여 923K에서는 약 1/3, 1098K에서는 약 1/10을 나타내었다. 그리고 1098K에서 18.0ks동안 유지시킨 주철모재 시편에서 원래의 모재표면을 기준으로 다공성의 외부스케일과 편상흑연을 따라 생성된 내부스케일로 구성된 두께 $60{\sim}70\;{\mu}m$의 두꺼운 산화스케일이 생성되었으나, 실리콘의 표면 합금층에서는 두께 $3{\sim}5\;{\mu}m$의 치밀한 외부 산화스케일만이 생성되었다. 실리콘 합금층의 단면 미소경도값은 MHV $300{\sim}1100$으로 그 변동폭이 심하였으나, 진공분위기에서 열처리(1223K, 18.0ks)한 경우 미소경도값의 편차는 MHV $300{\sim}500$으로 개선되었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.1
• /
• pp.46-53
• /
• 2013

Impedance spectroscopy is a non-destructive evaluation (NDE) method first proposed and developed for evaluating TGO layers with compressive stress inside thermally degraded plasma-sprayed thermal barrier coatings (PS TBCs). A bode plot (phase angle (h) vs. frequency (f)) was used to investigate the TGO layer on electrical responses. In our experimental study, the phase angle of Bode plots is sensitive for detecting TGO layers while applying compressive stress on thermal barrier coatings. It is difficult to detect TGO layers in samples isothermally aged for 100 hrs and 200 hrs without compressive stress, and substantial change of phase was observed these samples with compressive stress. Also, the frequency shift of the phase angle and change of the phase angle are observed in samples isothermally aged for more than 400 hrs.

• Elastomers and Composites
• /
• v.48 no.2
• /
• pp.167-171
• /
• 2013

Weatherability was examined according to aluminum particle size and its orientation used in PCM(Paint Coated Metal). Substrate delamination was checked by different UV transmission rate with QUV$^{(R)}$ (Q-LAB) equipment that can make accelerated UV irradiation. Film was prepared using three different types of conflake aluminum pastes under a PCM coating process and clearcoat was sprayed. UV transmission test results showed low transmission rate when EKART #790 having the smallest particle size and horizontal orientation was used. From the gloss retention results, gloss retention was highest in EKART #790 and followed by #770, #750.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.3
• /
• pp.129-136
• /
• 2006

The high velocity oxy-fuel sprayed coatings of 38Ni-23Co-20Cr-11Al-3Y-5Ta, 25Ni-34Co-20Cr-11Al-3Y-2Re and 32Ni-34.5Co-22Cr-11Al-0.5Ir (in wt%) were oxidized at 1000 and $1100^{\circ}C$ in air in order to find the alloying effect of Ta, Re and Ir on the oxidation properties of the NiCoCrAlY-base coatings. The primary phase of the coatings was $Ni_3Al$. The oxides formed on the coatings consisted primarily of ${\alpha}-Al_2O_3$, together with some $CoCr_2O_4,\;CoAl_2O_4$, and $Al_5Y_3O_{12}$. Tantalum oxidized to $Ta_2O_5$ and $Ta_2O_{22}$. However, no oxides of Re and Ir were detected by XRD owing to their thermodynamic inertness and/or their small amount.

• Corrosion Science and Technology
• /
• v.7 no.6
• /
• pp.328-331
• /
• 2008

Corrosion behaviour of water intake gate steel structures with different protective measures was investigated. Five material alternatives were taken for investigation, including: imported and recycled stainless steel, carbon steel with hot zinc spraying, painting and composite coatings. Results of corrosion rate for carbon steel, SUS 304, hot zinc spray coats in three water systems of Mekong river basin (saline, blackish and fresh) were also presented. Corrosion rate of carbon steel decreased with decreasing salinity in the investigated water environments. Meanwhile, these values for zinc coated steel, behaved by another way. Environmental data for these systems were filed and discussed in relation with corrosion characteristics. Method of Life Cycle Assessment (LCA) was applied in materials selection for water intake gate construction. From point of Life Cycle Cost (LCA) the following ranking was obtained: Zinc sprayed steel < Recycled stainless steel < Composite coated steel < Painting steel < SUS 304 From investigated results, hot zinc spray coating has been applied as protective measure for steel structures of water intake systems in Mekong river basin.

• Journal of the Korean Ceramic Society
• /
• v.29 no.2
• /
• pp.152-160
• /
• 1992

High-Tc superconductor thick films of YBa2Cu$\chi$O7-y (X=3, 3.5, 4) of which thickness varies from 100 $\mu\textrm{m}$ to 200 $\mu\textrm{m}$ were successfully prepared by plasma spraying method, and the characteristics of thick film depending on copper content and heat treatment conditions were investigated. Regardless of heat-treated temperature, the specimens with X=3 were composed of YBa2Cu$\chi$O7-y, Y2BaCuO5 and BaCuO3 phases. The specimens with X=4, however, were composed of YBa2Cu$\chi$O7-y phase at all heat treatment conditions. The specimens with X=4 composition showed the best superconducting characteristics after heat treatment at 925$^{\circ}C$, and the superconducting transition temperature with zero resistivity (Tc,zero) was 87K. The thick film lost superconductivity when the specimens were heat-treated at 950$^{\circ}C$ because of interdiffusion between superconductor elements and bond coating elements and Y2BaCuO5 phase was found was found to be main phase at the interface.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.346-353
• /
• 2001

Zirconia powder containing 3 mol% yttria(3Y-PSZ) with and with out Fe$_2$O$_3$ addition was coated on tile cast iron substrate by plasma spraying method. The erosion experiments were performed at temperatures from $25^{\circ}C$ to $600^{\circ}C$. A gas blast type erosion tester was used to examine erosion behavior of the specimens. The results of 3Y-PSZ coatings showed that tile erosion rate had maximum value at 40$0^{\circ}C$. It coincided with tile results of phase transformation tetragonal phase to monoclinic phase caused by low temperature thermal degradation. The tensile stress relaxation and the micro-hardness improvement significantly influenced on the erosion rate at $600^{\circ}C$. In the case of Fe$_2$O$_3$ added 3Y-PSZ coatings, the erosion rate of tested at $25^{\circ}C$ showed maximum value at 5.0 mol% Fe$_2$O$_3$ added coating. This tendency is caused by the improvement of mechanical properties and the tensile residual stress. The erosion rate at 200'c and 400'L showed significantly decrease by Fe203 addition. This decrease is believed to be the stabilization of the tetragonal phase and the increase of micro-hardness.