• 한국세라믹학회지
• /
• 제34권1호
• /
• pp.88-94
• /
• 1997

플라즈마 용사법(plasma spray method)으로 제작된 상용 가스 터빈 연소기의 finned segment의 열차폐용 코팅계, ZrO2-8wt%Y2O3 top coat/Ni-26Cr-5Al-0.5Y bond coat/Hastelloy X superalloy 기판에서 NiCrAlY bond coat의 산화 거동과 열피로 파괴에 대하여 조사하였다. 생성된 bond coat의 주산화물은 NiO, CrO2, Al2O3였다. ZrO2/bond coat계면에서 생성된 산화물의 분포는 고온에서의 사용 전에 이 계면 아래에 얇은 층의 Al2O3가없는 곳에서는 NiO 산화층 및에 Cr2O3와 Al2O3가 혼합된 형태를 나타내었다. 열피로에 의해 박리된 시편의 파면을 관찰한 결과, 파괴는 주로 ZrO2/산화층 계면보다 세라믹층내로 약간 치우쳐서 일어나지만, 산화층 내에서도 약간 일어남을 알 수 있었다.

• 한국재료학회지
• /
• 제24권2호
• /
• pp.116-122
• /
• 2014

$Bi_2Sr_2CaCu_2O_x$(Bi-2212) and $Bi_2Sr_2Ca_2Cu_3O_y$(Bi-2223) high-Tc superconductors(HTS) have been manufactured by plasma spraying, partial melt process(PMP) and annealing treatment(AT). A Bi-2212/2223 HTS coating layer was synthesized through the peritectic reaction between a 0212 oxide coating layer and 2001 oxide coating layer by the PMP-AT process. The 2212 HTS layer consists of whiskers grown in the diffusion direction. The Bi-2223 phase and secondary phase in the Bi-2212 layer were observed. The secondary phase was distributed uniformly over the whole layer. As annealing time goes on, the Bi-2212 phase decreases with mis-orientation and irregular shape, but the Bi-2223 phase increases because a new Bi-2223 phase is formed inside the pre-existing Bi-2212 crystals, and because of the nucleation of a Bi-2223 phase at the edge of Bi-2212 crystals by diffusion of Ca and Cu-O bilayers. In this study the spray coated layer showed superconducting transitions with an onset Tc of about both 115 K, and 50 K. There were two steps. Step 1 at 115 K is due to the diamagnetism of the Bi-2223 phase and step 2 at 50 K is due to the diamagnetism of the Bi-2212 phase.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.192-196
• /
• 2005

Key part of main equipment in a gas turbine may be likely to be damaged due to operation under high temperature, high pressure, high-speed rotation, etc. Accordingly, the cost for maintenance increases and the damaged parts may cause generation to stop. The number of parts for maintenance also increases, but diagnostics technology fur the maintenance actually does not catch up with the demand. Blades are made of precipitation hardening Ni superalloy IN738 and the like for keeping hot strength. The surface of a blade is thermal-sprayed, using powder with main compositions such as Ni, Cr, Al, etc. in order to inhibit hot oxidation. Conventional regular maintenance of the coating layer of a blade is made by FPI (Fluorescent Penetrant Inspection) and MTP (Magnetic Particle Testing). Such methods, however, are complicated and take long time and also require much cost. In this study, defect diagnostics were tested for the coating layer of an industrial gas turbine blade, using an infraredthermography camera. Since the infrared thermography method can check a temperature distribution on a wide range of area by means of non-contact, it can advantageously save expenses and time as compared to conventional test methods. For the infrared thermography method, however, thermo-load must be applied onto a tested specimen and it is difficult to quantify the measured data. To solve the problems, this essay includes description about producing a specimen of a gas turbine blade (bucket), applying thermo-load onto the produced specimen, photographing thermography images by an infrared thermography camera, analyzing the thermography images, and pre-testing for analyzing defects on the coating layer of the gas turbine blade.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.285-293
• /
• 2016

The high velocity oxygen fuel(HVOF) thermal spray is a kind of surface modification techniques to produce the sprayed coating layer. This process is to form the coating layer after spraying the powder to molten or semi-molten state by the ultra-high speed at the high-temperature heat source and conflicting with a substrate. The efficiency of thermal spraying is dropped, however, because the semi-molten powder in a spray process become a factor that degrades the mechanical property by the formed pore within the coating layer. Therefore, it is necessary to melt completely the thermal spray powder in order to produce the coating layer with an optimal adhesive force. In this study, to improve the wear resistance, corrosion resistance and heat resistance, the plungers of high-speed and ultra-high pressure reciprocating hydraulic pumps used in ironworks are manufactured with STS $420J_2$ and are coated by the powders of WC-Co-Cr and WC-Cr-Ni including the WC of high hardness using a HVOF thermal sprayer developed in this laboratory. These are called by the surface-modified plungers. The surface roughness, hardness, and surface and cross-sectional microstructure of these two surface-modified and conventional ceramic plungers are measured and compared before operation with after operation for 100 days. It is found that the values of centerline average surface roughness and maximum height for conventional ceramic plunger are 9.5 to 10.8 and 5.2 to 5.7 times higher than those of surface-modified ones coated by WC-Co-Cr and WC-Cr-Ni because the fine tops and bottoms on surface roughness curve of conventional ceramic plunger are approximately 100 times higher than those of surface-modified ones. In addition, the pores and scratches in the surface microstructure are considerably formed in the order of conventional ceramic, WC-Cr-Ni and WC-Co-Cr surface-modified plungers. The greater the WC content of high hardness powder is less the change in the plunger surface.

• 한국토양비료학회지
• /
• 제40권5호
• /
• pp.377-382
• /
• 2007

완효성을 부여하려는 물질의 외부에 광물입자를 이용하여 피복형 구조체를 제조하고 이의 방출조절능력을 카리비료에 대한 용출실험을 통해 평가하였다. 황산칼륨을 구형의 펠릿으로 제조하고 이의 표면에 평균입도 $13.0{\mu}m$와 $27.4{\mu}m$인 두 가지 장석분말을 이용하여 구조체를 제조하였다. 구조체의 두께와 소성하는 온도를 달리하여 펠릿을 제조하고 용출실험을 통해 구조체의 완효성 발현능력을 평가하였다. 칼륨의 용출은 burst effect효과가 커서 초기 용출율이 높았는데, 소성온도가 낮고 구조체가 얇은 시료에서 크게 나타났다. $1{\sim}55{\mu}m$의 입도를 갖는 장석 보다 $1{\sim}130{\mu}m$의 입도를 갖는 장석에 의한 구조체가 더 높은 충진율에 의해 용출속도를 늦출 수 있었다. 용출속도는 약 7일부터 정상상태의 용출속도를 보이기 시작하였고 용출패턴은 펠릿에 남아있는 칼륨의 농도에 비례하는 first order kinetic의 패턴을 나타내었다. 평균입도 $27.4{\mu}m$인 장석으로 1~2.6mm두께의 피복형 구조체를 만들어 $1050^{\circ}C$에서 소성한 팰릿의 경우에는 40일의 용출율이 약 43%를 나타내었다.

• 한국표면공학회지
• /
• 제34권5호
• /
• pp.499-502
• /
• 2001

Functionally gradient NiCrAlY/$ZrO_2$-$Y_2$$O_3$ and NiCrAlY/$ZrO_2$- $CeO_2$-$Y_2$$O_3$ coatings were prepared by APS. The as-sprayed microstructure consisted of metal-rich and ceramic-rich regions, between which $Al_2$$O_3$-rich layers existed owing to the oxidation during APS. During oxidation between 900 and $1100^{\circ}C$ in air, the pre-existing $Al_2$$O_3$-rich scales grew, due mainly to the preferential reaction of Al with inwardly transporting oxygen along the heterogeneous phase boundaries. As the amount of ceramics in the coating increased, the oxidation resistance increased.

• 한국안전학회지
• /
• 제9권1호
• /
• pp.28-30
• /
• 1994

Ultrasonic for MoSi$_2$/Y. C. Kim, C. K. Namkoong/MoSi$_2$in the silicides has excellence in the oxidation and corrosion resistence. When the solid state bonding sintered-MoSi$_2$/metal or the thermal sprayed coating by powder-MoSi$_2$on the metal are carried out, the defects may be occured at the bonded surface. So, the method for evaluating the existence of the defects by non-destructive inspection is strongly desired. Here, the characteristics of ultrasonic for sintered-MoSi$_2$are elucidated and the possibility of the detection of defects using by ultrasonic is investigated.

• 동력기계공학회지
• /
• 제16권2호
• /
• pp.49-53
• /
• 2012

Thermal spray coatings developed by deposition of splats, it formed by impacting molten droplets on substrates during thermal spray process. In this study, the Ni-based coatings were fabricated by thermal spray process with two different process parameters, oxygen gas flow and acetylene gas flow, with three different levels of each parameters. The morphology of splats and microstructure were observed by optical microscope. Hardness test were performed on the Ni-based coatings. It was confirmed that process parameters of thermal spray process have effect in morphology of splats. These effects also have important implications on the deposit microstructure and properties of Ni-based coatings.

• 동력기계공학회지
• /
• 제16권2호
• /
• pp.54-59
• /
• 2012

In the present study, process optimization for thermal-sprayed Ni-based alloy coating has been performed using Taguchi method and analysis of variance(ANOVA). Ni-based alloy coatings were fabricated by flame spray process on steel substrate, and the hardness test and wear test were performed. Experiments were designed as per Taguchi's L9 orthogonal array and tests were conducted with different Oxygen gas flow, Acetylene gas flow, Powder feed rate and Spray distance. Multi response signal to noise ratio (MRSN) was calculated for the response variables and the optimum combination level of factors was obtained simultaneously using Taguchi's parametric design.

• 신재생에너지
• /
• 제4권1호
• /
• pp.31-36
• /
• 2008

Stainless steels have been widely considered as metallic bipolar plates, due to their passive surface film, which is good for corrosion resistance. However, the high resistivity of the passive film increases interfacial contact resistance between the bipolar plates and the electrodes. Stainless steels thermal spray coated with a mixture of tungsten carbide and stainless steel powders showed that the coated layer safely combined with the matrix but they suffered many internal defects including voids and cracks. Many cracks were formed in the coated layer and the interface of the matrix and the coated layer during the rolling process. The coated and rolled stainless steels showed lower interfacial contact resistance and corrosion resistance than bare stainless steel because of low resistivity of tungsten carbide and numerous defects, which caused crevice corrosion, in the coated layer.