• Journal of Environmental Science International
• /
• v.24 no.6
• /
• pp.755-762
• /
• 2015

The present study was conducted to develop seed treatment for the production of healthy and clean peanut sprout. Dry heat treatment of peanut seeds reduced the incidence of the rot. The seed treatment condition at $52^{\circ}C$ for 10 h. was the most efficient without inhibiting seed viability significantly. Seeds were dark cultured at $27^{\circ}C$ for up to 9 days. The treatment of Indole-B and gibberellic acid influenced germination, T50, fresh, dry weight, hypocotyl length, hypocotyl length diameter, root length, number of lateral root and epicotyl of peanut sprout. There were no differences in the germinability of peanut seeds between gibberellic acid treatment methods but higher fresh weight was observed in the GA3 solution spray after 2 hour water soaking. The general growth and lateral root development of peanut sprouts were suppressed by Indole-B which is used for inhibiting root formation and promoting hypocotyls. The treatment of gibberellic acid promoted hypocotyl elongation, but it did not influence on the growth of hypocotyls and root system.

• Journal of Periodontal and Implant Science
• /
• v.35 no.4
• /
• pp.1039-1052
• /
• 2005

IMZ는 "intramobile cylinder implant system" (IMZ)로 독일에서 가장 오래되고 많이 사용되어진 임플란트 중 하나이다. 이 임플란트에 관한 장기적 성공률과 생존률에 대한 연구는 대개 80% 이상을 보고하고 있다. 그러나, 연세대학교 치과병원 치주과에서 식립된 83개의 임플란트에서는 이전의 연구와는 다른 결과를 나타내었다. 1. IMZ 임플란트의 생존률은 67.5% 였다. 2. 변연 치조골 소실에 대한 성공 기준을 적용한 결과 성공률은 49.4%로 나타났다. 3. 발거된 총 27개의 임플란트 중에서 임플란트 주위 골소실을 가지는 경우는 17개, 내부구조 파절은 4개, 식립체 파절은 5개로 보고되었다. 4. 10년 이상 생존된 임플란트에서 변연골 소실의 평균치는 2.82mm였다. IMZ 임플란트는 장기적으로 높은 실패율을 보고하였다. 이는 cylindrical design, titanium plasma flame spray coating, prosthodontic complication 등의 요소에 기인한 것으로 사료된다. 임플란트는 그 형태, 표면 처리 등 여러 가지 요인들에 의해 실패가 나타날 수 있으며 본 연구를 통해 임플란트의 개발 및 선택에 바탕이 될 수 있을 것으로 생각된다.

• Membrane Journal
• /
• v.15 no.4
• /
• pp.330-337
• /
• 2005

Water selective silica membranes were prepared fur use as membrane reactor for synthesis of dimethyl ether (DME) by methanol dehydration. Silica membranes formed on a Porous SUS tube by ultrasonic spray Pyrolysis (USP) and chemical vapor deposition (CVD) using tetraethoxysilane (TEOS) as precursor. The CVD-derived membranes formed higher level of trade-off line between water permeance and water/methanol selectivity than that of the USP-derived membranes. The membrane reactor possessing water permeance of $1.2\times10^{-7}\;mol\;{\cdot}\;m^{-2}\;{\cdot}\;S^{-1}\;{\cdot}\;Pa^{-1}$ and water/methanol selectivity of 10 exhibited increase in methanol conversion of about $20\%$ comparing to conventional reactor system. These findings led us to conclude that the dehydration membrane reactor simultaneously separating the water vapour produced in the reaction zone was effective in increasing the reaction conversion.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.5
• /
• pp.829-837
• /
• 1992

This paper presents a new approach for the analysis of hot strip rolling processes. The approach is based on the finite element method and capable of predicting velocity field in the strip, temperature field in the strip, temperature field in the roll, and roll pressure. Basic finite element formulations for heat transfer analysis are described with emphasis on the treatment of numerical instability resulting from a standard Galerkin formulation. Comparison with the theoretical solutions found in the literature is made for the evaluation of the accuracy of the temperature solutions. An iterative scheme is developed for dealing with strong correlations between the metal flow characteristics and the thermal behavior of the roll-strip system. A series of process simulations are carried out to investigate the effect of various process parameters including interface friction, interface heat transfer coefficient, roll speed, reduction in thickness, and spray zone. The results are shown and discussed.

• Polymer(Korea)
• /
• v.26 no.5
• /
• pp.670-679
• /
• 2002

1,3-bis(2-chloroethyl)-1-nitrosourea (BCNU, carmustine) is one of the effective chemotherapeutic agents which has been used clinically for treating malignant glioma. Poly(D,L-lactide-co-glycolide) (PLGA, molecular weight: 20000 g/mole. mole ratio of lactide to glycolide 75 : 15) is a well known biodegradable polymer used as a drug carrier for drug delivery system. In this study, we investigated the BCNU release behaviour of BCNU-loaded PLGA wafers containing poly (N-vinylpyrrolidone) (PVP) or polyethyleneoxide (PEO) and the effect of hydrophilic polymers incoporated in the wafers. BCNU-loaded PLGA microparticles with or without hydrophilic polymers were prepared by a spray drying method and fabricated into wafers by direct compression. Encapsulation efficiency of BCNU-loaded PLGA microparticles containing PVP and PEO was 85 ∼ 97% and crystallinity of BCNU encapsulated in PLGA decreased significantly initial release amount and release rate of BCNU increased with the increasing PVP or PEO amount. Morphological change and mass loss of wafers during the release test were confirmed that hydration and degradation of PLGA would be facilitated with an increase of hydrophilic polymers.

• Polymer(Korea)
• /
• v.26 no.5
• /
• pp.680-690
• /
• 2002

Implantable biodegradable wafers were prepared with pamidronate -loaded poly (L-lactide-co-glycolide) (PLGA, 75 : 25 mole ratio by lactide to glycolide, molecular weight : 20000 and 90000 g/mole) by direct compression method for the sustained release of pamidronate to investigate the possibility for the treatment of bone resorption. Pamidronate-loaded PLGA powders were prepared by means of physical mixing and spray drying with the control of formulation factors and characterized by scanning electron microscope and X-ray diffractometer. The pamidronate-loaded PLGA powders fabricated into wafers by direct compression under the constant pressure and time at room temperature. These wafers were also observed for their structural characteristic, release pattern, and degradation pattern. The release rate of pamidronate increased with increasing their initial loading ratio as well as increasing wafer thickness. The molecular weight of PLGA affects the release pattern : the higher molecular weight of PLGA, the faster release rate. It can be explained that the higher viscosity of high molecular PLGA solution at same concentration tends to aggregate PLGA and pamidronate resulting in unstable pharmaceutical dosage form. This system had advantages in terms of simplicity in design and obviousness of drug release rate and nay be useful as an implantable dosage form for the treatment of aural cholesteatoma.

• Korean Journal of Materials Research
• /
• v.16 no.11
• /
• pp.681-686
• /
• 2006

Plasma nitrocarburising and plasma post oxidation were performed to improve the wear and corrosion resistance of S45C and SCM440 steel by a plasma ion nitriding system. Plasma nitrocarburizing was conducted for 3h at $570^{\circ}C$ in the nitrogen, hydrogen and methane atmosphere to produce the ${\varepsilon}-Fe_{2-3}$(N, C) phase. Plasma post oxidation was performed on the nitrocarburized samples with various oxygen/hydrogen ratio at constant temperature of $500^{\circ}C$ for 1 hour. The very thin magnetite ($Fe_3O_4$) layer $1-2{\mu}m$ in thickness on top of the $15{\sim}25{\mu}m$ ${\varepsilon}-Fe_{2-3}$(N, C) compound layer was obtained by plasma post oxidation. A salt spray test and electrochemical testing revealed that in the tested 5% NaCl solution, the corrosion characteristics of the nitrocarburized compound layer could be further improved by the application of the superficial magnetite layer. Throttle valve shafts were treated under optimum plasma processing conditions. Accelerated life time test results, using throttle body assembled with shaft treated by plasma nitrocarburising and post oxidation, showed that plasma nitrocarburizing and plasma post oxidation processes could be a viable technology in the very near future which can replace $Cr^{6+}$ plating.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.5
• /
• pp.181-186
• /
• 2013

We performed plasma spraying for 2001 (Bi:Cu = 2:1), 0212 (Sr:Ca:Cu = 2:1:2) oxide powders. $Bi_2Sr_2CaCu_2Ox$ (2212) superconductor has been prepared by PMP-AT (partial melting process-annealing treatment). The 2212 phase is synthesized between Sr-Ca-Cu oxide coating layer (0212) and Bi-Cu oxide coating layer (2001) by movement of partial melted Bi on 2001 layer and the diffusion reaction (Cu, Sr, Ca) after PMP-AT. There are two different coating layers on joining process. The one is ABAB coating layers and the other is BAAB coating layers by arrangement of 2001 (A), 0212 (B) layers. We performed heat treatment these two different coating layers processes under same PMP-AT conditions. We obtained Bi-2212 superconducting layers at each experimental condition, and the result of MPMS, the critical temperature was showed about 78 K. But the microstructure images and result of EDS as each experimental variable were showed about the qualitatively different Bi-2212 superconducting phases. We also deduced the generation mechanism of Bi-2212 superconducting layer as a result of these experimental data, microstruc ture images, EDS data and phase diagram.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.19 no.1
• /
• pp.93-101
• /
• 2011

The modeling of SDR was carried out for the application of the solid waste incineration system. To find optimum operating condition for removal of acidic gases, computation fluid dynamic(CFD) model was used. In this study, the temperature profile of SDR(spray dry reactor) and the gas velocity profile for different models were investigated. In this model, the diameter of SDR was 3 meter and the height of SDR was 9 meter. The amount of inlet combustion gas of SDR was $6,125Nm^3/hr$ and the inlet temperature of SDR was 493 K. The amount of lime injection of SDR was 151 kg/hr. When the inlet shape of SDR was changed, the temperatur of SDR was changed and the gas velocity of SDR was 0.48 m/sec to 1.17m/sec and the outlet gas velocity of SDR was 6.9 m/sec to 7.42m/sec As a result of modeling, the average velocities in SDR and outlet were 0.489 m/sec and 7.424 m/sec, respectively, in which the temperature of outlet in SDR was 448 K.

• Journal of Information Technology Services
• /
• v.20 no.5
• /
• pp.119-136
• /
• 2021

Since the global spread of COVID-19, social distancing and untact service implementation have spread rapidly. With the transition to a non-face-to-face environment such as telework and remote classes, cyber security threats have increased, and a lot of cyber compromises have also occurred. In this study, cyber-attacks and response cases related to COVID-19 are summarized in four aspects: cyber fraud, cyber-attacks on companies related to COVID-19 and healthcare sector, cyber-attacks on untact services such as telework, and preparation of untact services security for post-covid 19. After the outbreak of the COVID-19 pandemic, related events such as vaccination information and payment of national disaster aid continued to be used as bait for smishing and phishing. In the aspect of cyber-attacks on companies related to COVID-19 and healthcare sector, we can see that the damage was rapidly increasing as state-supported hackers attack those companies to obtain research results related to the COVID-19, and hackers chose medical institutions as targets with an efficient ransomware attack approach by changing 'spray and pray' strategy to 'big-game hunting'. Companies using untact services such as telework are experiencing cyber breaches due to insufficient security settings, non-installation of security patches, and vulnerabilities in systems constituting untact services such as VPN. In response to these cyber incidents, as a case of cyber fraud countermeasures, security notices to preventing cyber fraud damage to the public was announced, and security guidelines and ransomware countermeasures were provided to organizations related to COVID-19 and medical institutions. In addition, for companies that use and provide untact services, security vulnerability finding and system development environment security inspection service were provided by Government funding programs. We also looked at the differences in the role of the government and the target of security notices between domestic and overseas response cases. Lastly, considering the development of untact services by industry in preparation for post-COVID-19, supply chain security, cloud security, development security, and IoT security were suggested as common security reinforcement measures.