• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.214-219
• /
• 2003

This paper includes real-time tractive force estimation method using standard vehicle sensors such as wheel speed, brake pressure, throttle position, engine speed, and transmission carrier speed sensor. Engine map, torque converter lookup table, shaft torque observer, and brake gain adaptation method are used to estimate the tractive force. To verify this estimator, measurement which uses strain-based brake torque sensor and estimation results are presented. All results was performed using a real vehicle in a real-time.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.388-394
• /
• 1998

In this paper, we propose a speed sensorless control of the saturated induction motor using the zero sequence third harmonic voltages and a compensation method of the stator resistance variations. The air-gap flux of the saturated induction motor contains the space harmonic components rorating synchronous frequency. As a function of the air-gap flux saturation, the dominant third harmonic voltage is used to compensate the non-linear variations of the mutual inductance depending on the saturation level of the motor. and also the stator resistance variations can be measured with the phase angle between the voltage vector and the zero sequencial voltages. The validity of the proposed compensation scheme in the speed sensorless control using rotor flux observer is verified by simulations.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.174-176
• /
• 2002

This paper presents an analysis of speed sensorless vector control systems using the rotor flux observers. For the comparison tests in this paper speed estimation schemes are the same. The performance of speed sensorless control is much dependent on the flux estimation performance. The experimental results are also included.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.3
• /
• pp.31-42
• /
• 1985

Thig paper used two feedback sensors, that is, potentiometer and tachometer in order to control DC motor. Also, the state feedback and kalman regular type in the linear system or the state feedback and on-off relay type in the non-linear system are used as control meth-ods for optimal control values. This compared and analyzed the control estimate of tracking angles by the estimate of three branches of methods of position and speed measured, position and speed by PD and position, speed and covariance by an observer.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.4
• /
• pp.199-205
• /
• 2012

This paper propose a improved parameter estimations of five-phase squirrel-cage induction motor(IM) for speed control system on field oriented control(FOC). In order to high performance control of ac the motors using a FOC and DTC(direct torque control) algorithm, there are required precise motor parameters for slip calculation, flux observer, controller gain, rotor position and speed estimation, and so on. We are suggest a estimation method of the motor parameters that developing five-phase squirrel-cage IM have a stator of concentrated winding for experimental. There are results of stator winding test, no-load test, locked rotor test, and obtained equivalent circuits using manufactured experimental apparatus. For presenting the superior performance of the speed control system in adapted the parameters, experimental results are presented using a 32-bit fixed point TMS320F2812 DSP with 1.5[KW] IM.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1102-1104
• /
• 2000

Recently effective system-on-a-chip design methodology is developed, and ASIC chip design is much studied for motor control. This paper investigates the design and implementation of ASIC chip for sensorless speed control of induction motor using VHDL which is a standarded hardware description language. The sensorless control strategy is to design an adaptive state observer for flux estimation and to estimate the rotor speed from the estimated rotor flux and stator current. The presented system is implemented using a simple electronic circuit based on FPGA.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.420-422
• /
• 1998

In this paper, we propose a position-speed control of servo system with a state estimator. And also we utilized two mass modelling in order to deals with real system accurately. The overall control system consists of two parts: the position-speed controller and state estimator. The Kalman filter applied as state - feedback controller is an optimal state estimator applied to a dynamic system that involves random perturbations and gives a linear,unbiased and minimun error variance recursive algorithm to estimate the unknown state optimally. Therefore we consider the error problem about the servo system modelling, the measurement noise at low-speed ranges a stochastic system, and implement a optimal state observer. Performance of the proposed state estimator are demonstrated by computer simulations.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.1
• /
• pp.98-106
• /
• 2001

This paper presents external load disturbance compensation that used to deadbeat load torque observer and regulation of the compensation gain by parameter estimator. As a result, the response of PMSM follows that of the nominal plant. The load torque compensation method is compose of a dead beat observer that is well-known method. However it has disadvantage such as a noise amplification effect. To reduce of the effect, the post-filter, which is implemented by MA process, is proposed. The parameter compensator with RLSM(recursive least square method) parameter estimator is suggested to increase the performance of the load torque observer and main controller. Although RLSM estimator is one of the most effective methods for online parameter identification, it is difficult to obtain unbiased result in this application. It is caused by disturbed dynamic model with external torque. The proposed RLSM estimator is combined with a high performance torque observer to resolve the problems. As a result, the proposed control system becomes a robust and precise system against the load torque and the parameter variation. A stability and usefulness, through the verified computer simulation and experiment, are shown in this paper.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.4
• /
• pp.247-254
• /
• 2004

The mechanical informations such as the rotor speed and angle are required to operate the Cylindrical Permanent Magnet Synchronous Motor(PMSM). A resolver or encoder is typically used to supply the mechanical informations. This position sensor adds length to the machine, raises system cost, increases rotor inertia and requires additional devices. As the result, there has been a significant interest in the development of sensorless strategies to eliminate the position sensor. This paper presents an implementation of the new sensorless speed comtrol scheme for a PMSM. In the proposed algorithm, the line currents are estimated by a observer and the estimated speed can be yielded from the voltage equation because the information of speed is included in back emf. But the speed estimation error between the estimated and the real speeds is occured by errors due to measuring the motor parameters and sensing the line current and the input voltage. To minimize the speed estimations error, the estimated speeds are compensated by using an instantaneous reactive power in synchronously rotating reference frame. In this paper, the proposed algorithm is not affected by mechanical motor parameters because the mechanical equation is not used. The effectiveness of algorithm is confirmed by the experiments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.104-111
• /
• 2018

The sensorless control of high efficiency air compressors using a permanent magnet type synchronous motor as an oil-free air compressor is quite common. However, due to the nature of the air compressor, it is difficult to install a position sensor. In order to control the permanent magnet type synchronous motor at variable speed, the inclusion of a position sensor to grasp the position of the rotor is essential. Therefore, in order to achieve sensorless control, it is essential to use a permanent magnet type synchronous motor in the compressor. The position estimation method based on the back electromotive force, which is widely used as the sensorless control method, has a limitation in that position errors occur due either to the phase delay caused by the use of a stationary coordinate system or to the estimated back electromotive force in the transient state caused by the use of a synchronous coordinate system. Therefore, in this paper, we propose a method of estimating the position and velocity using a rotation angle tracking observer and reducing the speed ripple through a disturbance observer. An experimental apparatus was constructed using Freescale's MPU and the feasibility of the proposed algorithm was examined. It was confirmed that even if a position error occurs at a certain point in time, the position correction value converges to the actual vector position when the position error value is found.